LBL Lighting Ambra User Manual

Page 1
Installation Instructions for
980AMBRAC
Ceiling
GP I :ENERAL RODUCT NFORMATION
This product can mount to either a 4" square electrical box with round plaster ring or an octagon electrical box.
This product is suitable for indoor dry locations only.
This product can be dimmed with a standard incandescent dimmer.
CAUTION - RISK OF FIRE
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
Use minimum 90°c supply conductors.
JC399AM_2D100
1.2
Install the Fixture
1A
CAP NUT
SHOE HORN BRACKET
1
Place the button head screw and washer from the inside through one of the canopy holes.
Place the narrow side hole of the shoe horn bracket onto the
2
exposed button head screw.
3
Finger tighten the cap nut completely to the button head screw to secure the shoe horn bracket in place.
WASHER
2
3
BUTTON HEAD SCREW
1
1B
4
CROSSBAR
5
#8-32 SCREW
5
Mount the crossbar to the electrical box with the two #8-32 screws.
ELECTRICAL BOX
5
NOTE:There will be a small gap between the shoe horn
bracket and canopy when the cap nut is completely tighten to button head screw.This gap is necessary when attaching the glass shade to shoe horn brackets.
Repeat step 1 through 3 for the other two shoe horn brackets.
4
1
Page 2
Install the Lamps
1C
6
8
6
Connect the fixture green wire to the ground in accordance with local electrical codes.
7
Connect the fixture white wire to neutral power line wire with a wire nut.
7
2A
SOCKET
CAUTION:To reduce the risk of a burn or electric shock during relamping, disconnect the power to the fixture.
Use Volt, WattType A19MAX 100120 Medium Base Lamp With Each Socket.
LAMP
8
Connect the fixture black wire to hot power line wire with a wire nut.
1D
THREADED STUD
11
CAP NUT
9
Place all wire and wire nut connections inside the electrical box.
10
11
CANOPY
1
For each socket, screw the lamp completely into the socket.
10
Slide the canopy holes completely onto the crossbar threaded studs.
11
Tighten the cap nuts completely to the threaded studs to secure the canopy in place.
2
Page 3
Install the Glass Shade
3A 3B
4
KNURLED NUT
PLASTIC WASHER
PLASTIC WASHER
GLASS SHADE
1
Place a plastic washer onto the cap screw.
2
From outside of the glass shade, insert the cap screw through one glass shade hole.
3
Place the second plastic washer onto the cap screw and finger tighten the knurled nut to secure the cap screw in place.
3
1
2
CAP SCREW
5
6
HOOK
6
Screw the three hooks completely to end of the three cap screws. Make sure the hooks are facing down.
Skip to section 3D to install the glass. If the clips do not reach the glass with the lamps installed, follow the steps in section 3C to install the hook extensions.
Repeat steps 2 through 5 for the remaining glass shade holes.
4
3C
HOOK
7
8
HOOK EXTENSION
7
Screw the female end of the three hook extensions onto the three cap screws.
8
Screw the male end of the three hook extensions onto the three hooks.
3
Page 4
3D
9 9
9
NOTE: Two people are recommended for the following step.
9
One person should hold the shade up to the fixture while the
9
SHOE HORN BRACKET
HOOK
9
other slips each of the hooks into the holes in the shoe horn brackets. Make sure the hooks are facing down.
CAUTION: Replace lamps in the fixture from top of the
glass shade. lift the glass shade.The hooks couldNEVER release, causing the glass shade to fall and break.
SAVETHESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2008 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a registered trademark of LBL Lighting. LBL Lighting reserves the right to change specifications for product improvements without notification.
A Generation Brands Company
4
Loading...