LBL Lighting 2-Circuit MO Element Adapter User Manual
Installation Instructions for
980MR2FIXC
Two-Circuit Monorail Fusion Jack Adapter
2-Circuit Monorail
GP I :ENERAL RODUCT NFORMATION
This product is ETL listed and suitable only for indoor dry locations
and approved for use at any height above the finished floor.
This product is intended to be used with LBL 2-Circuit Monorail
system.
Install the Adapter onto the 2-Circuit
Monorail for Down Light Fixtures
1A11A
CAP
2
1A6a1C
M3 SET SCREW
PENDADAPMONOFJ2_
1.5 MM ALLEN
6a
WRENCH
1.0
3
2-CIRCUIT MONORAIL
Unscrew the cap from the Fusion Jack adapter.
2
Select a place on the 2-Circuit Monorail where the fixture is
going to be mounted.
3
From the bottom, place the Fusion Jack adapter onto the
2-Circuit Monorail.
4
Replace and tighten the cap to the Fusion Jack adapter.
Make sure that the cap is not cross threaded.
FUSION JACK
ADAPTER
1A1B
FUSION JACK
ADAPTER
5
FIXTURE
FUSION JACK
CIRCUIT #1:
COMBINATION
OF THESE RAILS
To power up the fixture from circuit #1, tighten the M3 set
screw on top of the cap with the 1.5MM Allen wrench. Make
sure that the set screw is tight for proper power
connection.
1D
6b
CIRCUIT #2:
COMBINATION
OF THESE RAILS
6b
To power up the fixture from circuit #2, remove the M3 set
screw from top of the cap and screw it into the side of the
Fusion Jack adapter hole with the 1.5MM Allen wrench. Make
sure that the set screw is tight for proper power
connection.
NOTE:Never use more than one set screw to select
a circuit on the Fusion Jack adapter.
M3 SET SCREW
1.5 MM ALLEN
WRENCH
5
Push and screw the fixture Fusion Jack completely into the
Fusion Jack adapter.
NOTE:Do not load either circuit over the maximum
system rating.
1
Install the Adapter onto the 2-Circuit
Monorail for Up Light Fixtures
1A12A
2-CIRCUIT MONORAIL
3
2
Unscrew the cap from the Fusion Jack adapter.
2
Select a place on the 2-Circuit Monorail where the fixture is
going to be mounted.
3
From the top place the Fusion Jack adapter onto the 2-Circuit
Monorail.
4
Replace and tighten the cap to the Fusion Jack adapter. Make
sure that the cap is not cross threaded.
FUSION JACK
ADAPTER
CAP
1A2B
1A2C
6
CIRCUIT #1:
COMBINATION
OF THESE RAILS
WARNING: Use only circuit #1 when installing the
fixture as an up light.There is 24V between the middle
and top rail of the 2-Circuit Monorail.
6
To power up the fixture, tighten the M3 set screw on bottom
of the cap with the 1.5MM Allen wrench. Make sure that the
set screw is tight for proper power connection.
M3 SET SCREW
1.5 MM ALLEN
WRENCH
5
FUSION JACK
ADAPTER
5
Push and screw the fixture Fusion Jack completely into the
FIXTURE
FUSION JACK
Fusion Jack adapter.
SAVETHESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting.All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
2
A Generation Brands Company
A Generation Brands Company
Loading...