LBL Lighting 2-Circuit MO 4 Round Canopy Dual Feed User Manual
Installation Instructions for
980MR2ADPFC
4” Dual Flexible Power Feed Canopy
SPECIAL INSTALLATION
GENERAL PRODUCT INFORMATION:
This product is suitable for indoor dry locations only.
This product must be used with LBL Lighting 2-Circuit MonoRail
system only.
Install the Canopy
NOTE: Low voltage wires must be present in
electrical box before proceeding with these steps.
Refer to the instructions provided with the remote
transformer.
REMOTECNPY-DF-2C_
700MOPCEN_
NOTE: The Power Feed wires may be connected
directly to the transformer, Refer to the instructions
provided with the remote transformer for connection
details.
1.0
1A
HOT B2
COM2
HOT B1
SET SCREW
STRAIN RELIEF
COM1
HOT A1
HOT A2
IDENTIFICATION
TAG
1
1
Loosen (Do Not Remove) the 3 set screws on each
strain relief.
2
Before cutting the center power feed wires to the
desired length, move the wire identification tags down
the wire.
Cut the end power feed wires to the desired length.
3
4
With a sharp knife cut 1" from the end of the wire web
and separate the wires 8" from each other on each side.
5
Push the power feed wires through the strain reliefs
leaving at least 6” of cord in the back of the canopy for
wire connections.
6
Re-tighten the set screws.
1B
HOT A2
HOT B2
COM1
HOT A1
HOT A1
HOT A2
HOT B2
COM1
COM2
HOT B1
1
Note: If mounting the canopy onto an octagonal
electrical box, first mount the provided universal
mounting plate before proceeding to this step.
7
Strip 1/2" off the wire ends.
8
Connect the center power feed wire marked "HOT1" to
electrical box marked "HOT1" with a wire nut.
9
Connect the center power feed wire marked "HOT2" to
electrical box wire marked "HOT2" with a wire nut.
10
Connect the power feed wire marked "COM" to electrical
box wire marked "COM" with a wire nut.
11
Repeat the connections for the second power feed wires
1
for the B side.
COM2
HOT B1
1C
2C
13
1
13
812
Properly place the all the wires and wire nut connections
#8-32
SCREW
into the electrical box.
813
Mount the canopy to the electrical box/mounting plate
with two #8-32 screws provided.
Connecting the Center Power Feeds
2A
TWO-CIRCUIT MONORAIL TWO-CIRCUIT MONORAIL
#6-32 SET SCREW
81
Insert the three pin insulated connector into each end of
the Two-Circuit MonoRail.
THREE PIN INSULATED CONNECTOR
1
2
1/16 ALLEN WRENCH
2-CIRCUIT MONORAIL
POWER FEED
HOUSING
6
7
POWER FEED CAP
6
Place one power feed housing onto one electrically isolated
Two-Circuit MonoRail sections.
7
Screw the power feed cap completely to the power feed
housing. Make sure that the power feed cap is not cross
threaded.
2D
HOT 1
KNURLED CAP
9
POWER FEED CAP
SCREW
HOT 2
82
Tighten the three #6-32 set screws on the three pin
insulated connector with the 1/16 Allen wrench
provided.
NOTE: To avoid stripping the three pin insulated
connector, do not over tighten the #6-32 set screws.
2B
POWER FEED
HOUSING
3
POWER FEED CAP
SCREW
3
Remove the power feed cap from the power feed housing.
4
Completely back out the screw on the power feed cap.
5
Loosen (Do Not Remove) the set screw and knurled cap on
the power feed housing, and pull the middle contact wire
slightly out so that the middle contact is not exposed.
MIDDLE
CONTACT
4
7
8
Tighten the screw on the power feed cap for proper power
8
COM
connection.
9
Tighten the knurled cap for proper power connection, and
tighten the set screw near the knurled cap.
10
Repeat steps 1 through 7 to connect the other power feed
housing an electrically isolated section of Two-Circuit
MonoRail.
CAUTION: Ensure that the power feed connections
are on sections of Two-Circuit MonoRail that are
isolated from each other.
5
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2014 LBL Lighting. All rights reserved. The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
A Generation Brands Company
2
Loading...