LAYON BS036RM User Manual

BS036RM
Bluetooth Srereo Headset
User Manual

Bluetooth headset should be used with the compatible devices
which support Bluetooth wireless technology. This allows you the
freedom to make two calls (or one call) at any time.
Please read this user manual carefully before using the headset,
and also read your device's user manual regarding the Bluetooth
function, and pay attention to those important safety and
maintenance information.
Please keep the headset away from children.

1.Specifications

Bluetooth Specification V3.0
Bluetooth Profiles Supported Headset, Handsfree,A2DP1.2,HFP1.5,HSP1.2
Transmission Power Class 2
Operation Range up t0 10 Meters
Frequency Range 2.402-2.480GHz
Battery Built-in Rechargeable

3.7V/70mAH Li-polymer Battery
Charging Voltage DC4.75-5.25V
Charging Time About 2 hours
Music Playing Time Up to 3.5 hours
Talk Time* Up to 4 hours
Standby Time * up t0 100 hours
Dimensions(mm) L36xW14.5xH6
Weight About 6.6g

Note:The time mentioned above may vary due to user's operation mode and
device settings.

2.Structure Sketch

1.Volume Key+(V+) 2.Speaker

3.Volume Key -(v-) 4.Multifunction
Botton(MFC) 5.Charging Socket 6.Microphone

7.Headset Connecting

3.Basic Operations

3.1.Charging Your Headset
*prior to using the headset for the first time, please fully charge the battery.
*Approximately 2 hours are required to fully charge the headset.
*The indicator light turns red while being charged, and will turn blue automatically after
being fully charged.
*When the headset is running out of battery, the indicator light will flash red (the
headset will switch off automatically when the battery is drained). Please charge the
headset as above steps in time to prolong the battery's useful life (Charging indication
will be delayed for a few minutes if the headset has not been used for a long time or the
battery is drained).

3.2.Note :
*Check the charging device is suit to the headset
*Use only the supplied charger to charge the headset, or could be dangerous and obey
the validation for this product or the maintenance article.
*Do not attempt to force open the built-in battery as this could damage the headset.
*If left unused, a fully charged headset will loose its power automatically.It is
recommended to charge the headset each three months.
*Do not leave the headset in a too hot or too cold condition (best between 15 ℃ and
25℃) which may affect the headset's operations although it is fully charged.
*Do not dispose of the headset into a fire or water

4.Turning on the Headset
In OFF MODE, long press and hold the MFB for 4 seconds until you hear a short beep
and the indicator light flashes blue for 3 times, then the headset will enter into
STANDBY MODE.

5.Turning off the Headset

In ON MODE, press and hold MFB for 6 seconds until you hear a short beep and the
indicator light flashes red for 3 times, then the headset will enter into OFF MODE.

6.Pairing Your Headset with a Bluetooth Mobile Phone

6.1Ensure the headset is off, and the distance between your headset and phone is within
l meter

6.2. Press and hold MFB until the indicator light flashes blue and
red alternately as PAIRING MODE.

6.3. Activate the bluetooth function on the phone, and search bluetooth devices (see the
user guide of your phone for instructions).

6.4. Select headset “BS036RM” from the found devices list of the phone.

6.5. Enter the passkey '0000", confirm to pair the headset with your phone and the
headset will enter into connecting mode.(If the pairing cannot be completed within 5
minutes after the PAIRING MODE have been activated, the headset will enter into the
STANDBY MODE. Repeat above steps to do the pairing again).

6.6. Ensure the distance between your headset and phone is within 10 meters, and
without any obstacles, you can use the headset freely.