Press and hold to turn on/off phone
Press to lock/unlock the screen
5
Volume Key
Adjust the Volume
6
Camera
Camera Lens
7
Flash Light
Camera Flash light
Standby Screen & Icons
Status Icon
Description
Signal indicator for SIM
Using headset
Mute
Vibrate mode
Alarm
Background playing / pausing
This phone provides multiple Standby screens. Through the instruction and
various icons on the screen, you can have the operating information needed.
2
Memory card installed
Bluetooth on
Device connected via USB
EDGE
Airtel/ Airtel
Network carrier of Card 1/ Card 2
Getting Started
Please read the safety instructions in the "Safety Information and Notices"
section before use.
Inserting the SIM card and the Battery
Remove the back cover
Make sure the phone is switched off. You need to remove the back cover of
your phone before you can insert the SIM card. Hold the phone with the front
facing downwards; pull the battery cover downwards and lift the cover
upwards to remove it.
3
Remove the battery
Put your fingers on the black holder located at the bottom of the battery slot
and then lift the battery up to remove it.
Insert the SIM card
Make sure that the clipped corner of the SIM card is facing the correct
direction (clipped corner at top left) and the metallic contacts are facing
downwards. Slide the SIM card into the card slot until it stops.
Insert the battery
With the metallic contacts of the battery facing the metallic contacts in the
battery slot, press the battery down until it locks into place.
Replace the back cover
Align and hook the back cover to the top of the battery slot and then push
the cover upwards until it locks into place.
Inserting Micro SD card
With the metal contacts facing down, gently slide the micro SD card into the
4
slot marked SD ( near SIM1).
Switch On/Off
Long press the power key to switch on/off the phone.
After inserting the SIM card, the screen will show the notes in the following
order when the phone is switched on:
if you have already set the SIM code, Please type in PIN,.
Search— the handset will be searching for proper network connection.
Unlock SIM Card
To avoid illegal use, the SIM card is enciphered with PIN (personal
identification number) as a protection. When this function is ON and you
have already set a PIN code, you need to type in PIN code every time, the
handset is switched on in order to unlock SIM card and use the handset.
You can turn off the SIM PIN code. Yet in this situation, the SIM card can't
prevent illegal use.
Input PIN code, press arrowhead icon to erase typing error and press OK to
end typing. For example, if the PIN code is set as 1234, then type "1234"
then press OK.
The SIM card will be locked if you type in wrong code for three times
continuously. The handset will inform you to type in PUK code.
Attention: Your network provider will set a standard PIN code (four to eight
numbers) for your SIM card. It is recommended that you change the code
into a personal code as soon as possible.
Connection to Network
When the SIM card is successfully unlocked, the handset will automatically
search for available network (the lock screen shows searching). The
handset will show the information of the network provider; the status bar will
show the signal strength and the network condition once the handset is
successfully connected to a network.
Note: If the lock screens shows "Emergency", it means that you're out of
5
network coverage (service coverage) or your card is not valid, yet you can
still have emergency calls based on signal strength.
Charging the Battery
Ensure the battery inserted in the handset. To charge the battery, plug in the
charger connector at the bottom of your phone (USB interface) and then
plug the other end into an AC power socket.
The battery symbol indicates the charging status. While charging, the
charge indicators will scroll. When all the scroll bars are steady, the battery
is fully charged.
Disconnect the charger from the phone.
Disconnect the charger from the AC power socket.
Note: If the battery is powerless, the battery icon will reappear after a few
minutes of charging.
Basic Function
Make Calls
When the network provider icon appears on the standby screen, you can call
out or answer calls. The indicator on the upper right part shall show the
signal strength.
Quality of connection will be greatly influenced by obstructions. So
movement in a small range may effectively improve the quality of
connection.
Make Domestic Calls
Use virtual keyboard to enter phone numbers and then press Dial icon to call.
If you need to change the phone number, please press the delete key on the
touch screen to delete. When the call is answered, the screen shall show the
connection status.
Call Extension Phone
Some of the extension phones can't be directly connected to. Use the virtual
6
Loading...
+ 20 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.