Lava Aire Italia Aviator X2 User Manual

INSTRUCTIONS MANUAL

ELECTRIC COMMERCIAL GRADE PATIO COOLER

@2012.11-V1.1 Aviator X2 Page 2 of 15

Contents

Ø Instruction............................................................................ ....3

Ø Outline Drawing.......................................................................3

Ø Wiring Diagram...................................... ................................4

Ø Installation Instructions.........................................................5-8

Ø Checking after Installation........................................................8

Ø Trial Operation.....................................................................9-10

Attentions..........................................................................11-12

Ø

Ø Common Malfunction Analysis and Maintenance..............13-15

PICTURES ARE ONLY FOR INFORMATION, TAKE MATERIAL OBJECT AS STANDARD

@2012.11-V1.1 Aviator X2 Page 3 of 15

■Instruction

Aviator X2 Misting Air Coolers adopt user-friendly design and appearance. The

mist particles (diameter of 10-25 microns) emitted by misting device will take away the

heat through evaporation, which travel to target area when the fan blows. In the effective

area, it can decrease temperature by 3-8℃and help increase relative humidity, reduce

dust and purify air, which makes a comfortable living & working space.

The internal structure uses independent control devices and human-intelligent

warning protection system, which separates electricity from water so as to eliminate safety

risk. Featured by non-clogged misting system, low energy consumption, low pollution, low

noise, low heat & low carbon, our products are widely used in various public places, such as

open square, playgrounds, stadiums, airports, walk streets, bus stations, outdoor restaurant

and villa gardens; they are also used in industrial workshops of textiles, porcelain, casting

factories & etc.

■Outline Drawing

Fan head

Mist Regulating Switch

Pushing Handle

Control Panel

Water Tank

Wheels

@2012.11-V1.1 Aviator X2 Page 4 of 15

■ Wiring Diagram

Aviator X2

Aviator X4

@2012.11-V1.1 Aviator X2 Page 5 of 15

■ Installation Instructions

1、 Wheels Installation

Take out the Water Tank from the box, overturn it, and then fasten the 4 wheels on the

corresponding position with 16 sets of M8X16 Hex Head Cap Screw, spring washer and flat

washer. (Picture 1)

When using " automatic adding water", please take off the cover, then fix the weaved pipe.

When the weaved pipe is apart from the water supply, please screw on the choke plug so as to

avoid water leakage.

Remarks: As the Water Tank is very heavy, please be careful to avoid scratches of Water

Tank or hurt of the assemblers.

2、Fasten the Submersible Pump and Level Sensor

Turn the Water Tank with installed wheels back, and fasten the Submersible Pump and

Level Sensor inside the Water Tank. (see Picture 2)

Remarks: Put the Submersible Pump into the corresponding trench and press it. It will be

Cover

Nut

Picture 2

choke plug

Picture 1

Make sure the
water inlet is not
shielded.

Rubber Ring

Bottom of

water tank

@2012.11-V1.1 Aviator X2 Page 6 of 15

fasten by sucks installed beneath the pump.

Fasten the Level Sensor with the Nut into the corresponding trench. Make sure the

floater is flapped down like the picture shows.

3、 Combine Main Part and Water Tank

Lock the 4 wheels, and then place the Main Part on the Water Tank. (Picture 3)

When installing,

please align the 2

arrows of the 2 parts.

Picture 3

Rip off the protective coating of the Electricity Box on the Main Part, take it out and then

fasten the two connecting plate together with 4 M6X20 Butterfly screws. (see Picture 4)

Picture 4

4、Connect the Electric Wire of Submersible Pump and Level Sensor