Laurel Metal 2100 User Manual

Coin Mechanism Instructions

Only a screwdriver is required to change vend prices.

1. Remove the Empty Lock Rod (2100-127) by
grasping the top of the Rod in your left hand,
bowing the center of the Rod outward and pulling
it to the left to disengage it from the slot in the
side of the Magazine Assembly (2100-D1).

2. Remove the 3 screws holding the Coin Mechanism
(2100-D101) to the Magazine Assembly.

3. Pull the Coin Mechanism forward slightly to
disengage its rear flange from the locating slot at
the rear of the cabinet. Move the unit to the left to
disengage the Actuating Pin on the Pull Rod
(2100-31) from the slot in the Actuating Arm
(2100-12) on the side of the Magazine.

4. Look at the Coin Gate (2100-A112) at the bottom
of the Coin Mechanism. A coin-stop screw
(#8-32 x 1/2”) is inserted in one of the 3 stop
positions. The price decal indicates the proper
stop position for vending at 50¢, 75¢ or $1.00.
For vending at 25¢, insert the #6 self tapping
screw in the hole under the Coin Gate
(fold open the Gate to expose the hole).

5. Re-install the Coin Mechanism, making sure to
engage the Actuating Pin in the slot of the
Actuating Arm in the side of the Magazine. Enter
the locating slot at the rear of the cabinet and
secure the unit with the 3 screws.

6. With several of the top shelves down (or all of them)
re-install the Empty Lock Rod by first inserting its
lower end in the hole of the Empty Lock Rod
Bracket (2100-106) and then inserting the top in the
slot in the Magazine Frame. The Rod must be
bowed outward in the center to insert it in the
Magazine. As an option, the Empty Lock Rod’s
lower end can be inserted in the Bracket
(2100-106) before the Coin Mechanism is installed.

Customer Service

Should you need repair, parts may be sent to:

Laurel Metal Products

3500 W. Touhy Ave.

Lincolnwood, IL 60712

Please include phone number and return address.

Limited Warranty

Laurel Metal Products warrants that the goods
described in this warranty are free from defects in
workmanship and materials for the period of six (6)
months.

For breach of the express warranty and any implied
warranty on this product, you are limited to the fol­lowing damages:

If within six (6) months from the date of purchase,
this product fails due to a defect in materials or
workmanship, Laurel Metal will repair or replace it
free of charge. In no event shall Laurel Metal be
liable for incidental or consequential damages.
Laurel Metals’ liability for any claims arising out of
this warranty shall not exceed the purchase price of
the product.

NOTE: some states do not allow the exclusion or
limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to
you.

This warranty does not cover damage resulting from
accident or from misuse or alteration of the product.

The term of this warranty begins on the date the prod­uct is purchased by you, and continues for a period of
six (6) months from that date.

To obtain performance of any obligation under this
warranty, you must return the complete product
prepaid, together with a description of the problem,
approximate date of purchase, your name, address
and telephone number, to the address listed above.

This warranty gives you specific legal rights, and you
may also have other rights that vary from state to state.

This warranty covers any mechanical vender manu­factured by Laurel Metal Products.

MODEL 2100

Drop Shelf Vender

If you need to drop the shelves without going through
the effort of inserting quarters, simply push the Latch
Wire (under each shelf) with your fingernail or any
flat tool, such as a screwdriver.

3/10

3500 W. Touhy Ave.

Lincolnwood, IL 60712

Toll Free [phone]

[phone]
Fax # [phone]
www.laurelmetal.com

Operation & Service

Manual

The vender can be mounted on any vertical surface
without removing any part of the unit. Any standard
fastener not larger than 3/8" diameter such as wood
screws, expansion bolts, machine bolts or carriage
bolts can be used depending on the type of wall. The
wall section selected for installation should be sturdy.

The top two fasteners should be loosely installed in the
wall with the heads of the fasteners projecting out
approximately 1/4" from the wall. Raise the top shelf of
the magazine into its vend position to expose one of
the two top mounting holes in the back of the cabinet.
The keyhole shape of the mounting holes will permit
you to hang the cabinet on the two fasteners. While in
this unsecured position, mark the bottom mounting
holes on the wall and remove the cabinet. Install the
bottom two fasteners and secure the cabinet to the
wall using washers under the heads of all fasteners.

Model 2100 Coin Mechanism

Part #2100-D101

Coin Acceptor

2100-29

Spring-Coin

Platform

2100-111

Coin Return Rod
2100-119

Knob
2100-32

Model 2100 Exploded ViewInstallation

8

7

9

4

9

6

1

2

5

3

Loading

The shelves can be easily and quickly reset into the
vend position (horizontal) by running the index finger of
your right hand up the right side of the shelves. This
“fanning” will take only seconds to reset all 24 shelves.

The top shelf has an automatic empty device that will
cause the coin mechanism to reject all coins when the
vender is empty. Therefore, it is extremely important to
load from the top shelf down if the vender will not be
fully loaded during restocking.

Coin Mechanism Features

The standard coin mechanism in the vender accepts
U.S. quarters and will be factory set to vend at 50¢,
unless otherwise requested. Instructions for changing
the price setting are given under the heading “Coin
Mechanism Instructions”. Whenever the vend price
is set for 50¢, 75¢ or$1.00, a customer can retrieve
his quarters prior to vending by pushing the Coin
Return Button. There is no coin return function when
the vender is set at 25¢; pushing the Coin Return
Button will, however, clear all bent or steel slugs out
of the Coin Acceptor.

Coin Platform

2100-A109

Scavenger Lever

2100-A114

Ratchet

2100-115

Pull Rod

2100-A31

Ratchet Pawl

2100-23

Coin Gate

2100-A112

Front View of Coin Mechanism

Rear V

iew of Coin Mechanism

Bracket-Empty
Lock Rod
2100-106

Link
2100-118

Spring-Ratchet
2100-124

Lock Lever
2100-116

Actuating Pin
2100-33

Number Part # Description

1 2100-12 Actuating Arm
2 2100-D1 Magazine Assembly
3 2100-D101 Coin Mechanism
4 2100-A45 Cabinet
5 2100-127 Empty Lock Rod
6 300-A69 Coin Box w/Lock
7 2100-B125 Door w/Hinge
8 2100-63 Security Frame
9 2100-64 Side Bar

Model 2100-D Diaper Vender

Part # Description
2100-55D-U Door Lock - Upper - Key #2101
2100-55D-L Door Lock - Lower - Key #2101
2100-59D-U Door Lock - Upper - Key #2345
2100-59D-L Door Lock - Lower - Key #2345
2100-137 Key - Coin Box - Key #ES203
2100-137D Key - Diaper Vender Door - Key #2101
2100-139D Key - Diaper Vender Door - Key #2345