Label Picture Description QTY
A Backrest with Leg 1
B Left Panel with Leg 1
C Right Panel with Leg 1
Caution : You must read this before you proceed
Armless Chair
Page 1 OF 6
D Seat 1
E Back Cushion 1
F Seat Cushion 1
Label Picture Description QTY
①
Bolt Cap 11
②
Bolt (M6*45mm) 11
③
Washer 11
④
Spring Washer
(Ø16*2mm)
11
⑤
Allen Key 1
Before Beginning
Assembly:
Page 2 OF 6
Step 1
Open the carton and place all part on a clean and soft surface.
Place the Backrest with Leg(A) against the Right Panel with Leg(C) as shown above.
Attach the Backrest with Leg(A) to Right Panel with Leg(C) using the Bolts(②), Spring Washers(④)
and Washers(③) with Alley Key(⑤).
Do not fully tighten the bolts.
Over View
This Armless Chair has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Armless Chair parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the parts and steps
before assembly.
Backrest with Leg(A)
Left Panel with Leg (B)
Right Panel with Leg(C)
Seat(D)
Seat Cushion(F)
Back Cushion(E)
Page 3 OF 6
Place the Left Panel with Leg(B) facedown on the clean and soft suface.
With the help of your adult partner, place the Backrest with Leg(A) against Left Panel with Leg(B).
Attach the Left Panel with Leg(B) to Seat(D) and Backrest with Leg(A) using Bolts(②), Spring
Washers(④) and Washers(③) with Alley Key(⑤).
Tighten all Bolts at all joints completely at this stage.
Attach the Seat(D) to Right Panel with Leg(C) using Bolts(②), Spring Washers(④) and Washers(③)
with Allen Key(⑤).
Do not fully tighten the bolts.
Step 3
Step 2
Page 4 OF 6
Place the Seat Cushion(F) and Back Cushion(E) on the Armless Chair.
Your Armless Chair is ready for use.
This Armless Chair can only be used on a flat, level surface.
Step 4
Turn the Armless Chair face down on the clean, non-marring surface.
Use the Bolt Cap(①) to cover all Bolts.
Step 5
Place the Armless Chair on a level surface to check the wobbles.
If the Armless Chair wobbles, adjust the Levelers on the bottom of the Legs to make it level.
Step 6
Page 5 OF 6
Page 6 OF 6
Label Picture Description QTY
G Backrest with Leg 1
H Left Armrest with Leg 1
Caution : You must read this before you proceed
Left Armchair
Page 1 OF 7
I Right Panel with Leg 1
J Seat 1
E Back Cushion 1
F Seat Cushion 1
Label Picture Description QTY
① Bolt Cap 11
②
Bolt (M6*45mm) 11
③
Washer 11
④
Spring Washer
(Ø16*2mm)
11
⑤
Allen Key 1
Page 2 OF 7
Overview
This Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview
of the Armchair parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Before Beginning
Assembly:
Left Armrest with Leg(H)
Backrest with Leg (G)
Seat (J)
Right Panel with Leg (I)
Back Cushion (E)
Seat Cushion (F)
Page 3 OF 7
Step 2
Step 1
Place the Left Armrest with Leg(H) facedown on a clean, non-marring surface.
Place the Backrest with Leg(G) on the Armrest with Leg(H) being sure to insert dowel on Armrest with
Leg(H) into mounting position on Backrest with Leg(G).
Attach Backrest with Leg(G) to Left Armrest with Leg(H) using Bolts(②), Spring Washers(④) and
Washers(③) with Allen Key(⑤) as shown above.
Do not fully tighten the bolts.
Place the Seat(J) onto the Backrest with Leg(G) and Left Armrest with Leg(H) as shown.
Attach Seat(J) to Backrest with Leg(G) and Left Armrest with Leg(H) using Bolts(②), Spring Washers(④)
and Washers(③) with Allen Key(⑤) as shown above.
Do not fully tighten the Bolts.
Dowel
Page 4 OF 7
Turn the Armchair face down.
Use the Bolt Caps(①) to cover all Bolts.
Step 3
Place the Right Panel with Leg(I) facedown on a clean, non-marring surface.
With the help of your adult partner, place Backrest against Right Panel with Leg(I).
Attach the Right Panel with Leg(I) to Backrest with Leg(G) and Seat(J) using Bolts(②), Spring
Washers(④) and Washers(③) with Allen Key(⑤) as pictured above.
Tighten all Bolts at all joints completely at this stage.
Step 4
Page 5 OF 7
Step 6
Place the Seat Cushion(F) and Back Cushion(E) on the Armchair.
Your Armchair is ready for use.
This Armchair can only be used on a flat, level surface.
Step 5
Place the Armchair on a level surface to check the wobbles.
If the Armchair wobbles, adjust the Levelers on the bottom of the Legs to make it level.
Page 6 OF 7
Page 7 OF 7
Label Picture Description QTY
K Backrest with Leg 1
L
Right Armrest with
Leg
1
Caution : You must read this before you proceed
Right Armchair
Page 1 OF 7
M Left Panel with Leg 1
N Seat 1
E Back Cushion 1
F Seat Cushion 1
Label Picture Description QTY
① Bolt Cap 11
②
Bolt (M6*45mm) 11
③
Washer 11
④
Spring Washer
(Ø16*2mm)
11
⑤
Allen Key 1
Page 2 OF 7
Before Beginning
Assembly:
This Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview
of the Armchair parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Overview
Right Armrest with Leg (L)
Backrest with Leg(K)
Seat (N)
Left Panel with Leg (M)
Back Cushion (E)
Seat Cushion (F)
Page 3 OF 7
Place the Seat(N) onto the Backrest with Leg(K) and Right Armrest with Leg(L) as shown.
Attach Seat(N) to Backrest with Leg(K) and Right Armrest with Leg(L) using Bolts(②), Spring
Washers(④) and Washers(③) with Allen Key(⑤) as shown above.
Do not fully tighten the Bolts.
Step 1
Place the Right Armrest with Leg(L) facedown on a clean, non-marring surface.
Place the Backrest with Leg(K) on the Armrest with Leg(L) being sure to insert dowel on Armrest with
Leg(L) into mounting position on Backrest with Leg(K).
Attach Backrest with Leg(K) to Left Armrest with Leg(L) using Bolts(②), Spring Washers(④) and
Washers(③) with Allen Key(⑤) as shown above.
Do not fully tighten the bolts.
Step 2
Dowel
Page 4 OF 7
Step 3
Place the Right Panel with Leg(M) facedown on a clean, non-marring surface.
With the help of your adult partner, place Backrest against Right Panel with Leg(M).
Attach the Right Panel with Leg(M) to Backrest with Leg(K) and Seat(N) using Bolts(②), Spring
Washers(④) and Washers(③) with Allen Key(⑤) as pictured above.
Tighten all Bolts at all joints completely at this stage.
Step 4
Turn the Armchair face down.
Use the Bolt Caps(①) to cover all Bolts.
Page 5 OF 7
Place the Armchair on a level surface to check the wobbles.
If the Armchair wobbles, adjust the Levelers on the bottom of the Legs to make it level.
Step 5
Step 6
Place the Seat Cushion(F) and Back Cushion(E) on the Armchair.
Your Armchair is ready for use.
This Armchair can only be used on a flat, level surface.
Page 6 OF 7
Page 7 OF 7
Label Picture Description QTY
O Top Panel 1
P Front/Back Panel 2
Q Side Panel with Legs 2
Caution : You must read this before you proceed
Ottoman
Page 1 OF 6
U Seat Cushion 1
Label Picture Description QTY
① Bolt Cap 13
②
Bolt (M6*45mm) 13
③
Washer 13
④
Spring Washer
(Ø16*2mm)
13
⑤
Allen Key 1
Before Beginning
Assembly:
Page 2 OF 6
Step 1
Open the carton and place all parts on a clean, non-marring surface.
Attach the Side Panels with Legs(Q) to the Front and Back Panels(P) using Bolts(②), Spring Washers(④)
and Washers(③) with Allen Key(⑤) as shown above.
Do not fully tighten the Bolts.
Overview
This Ottoman has multiple parts and may require up to 30 minutes to assemble. To give you an overview
of the Ottoman parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Top Panel(O)
Side Panel with Leg(Q)
Front Panel(P)
Seat Cushion(U)
Page 3 OF 6
Step 2
Place the Top Panel(O) facedown on a clean and soft surface.
With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(O) as
shown above.
Attach the Top Panel(O) to the Front and Back Panels(P) and Side Panels with Legs(Q) using Bolts(②),
Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above.
Tighten all Bolts at all joints completely at this stage.
Step 3
Use the Bolt Cap(①) to cover all Bolts.
Page 4 OF 6
Place the Seat Cushion(U) on the ottoman.
Your Ottoman is ready for use.
This Ottoman can only be used on a flat, level surface.
Place the Ottoman on a level surface to check the wobbles.
If the Ottoman wobbles, adjust the Levelers on the bottom of the Legs to make it level.
Step 5
Step 4
Page 5 OF 6
Page 6 OF 6
Label Picture Description QTY
R Top Panel 1
S Front/Back Panel 2
T Side Panel with Legs 2
Caution : You must read this before you proceed
Table
Page 1 OF 6
Label Picture Description QTY
① Bolt Cap 13
②
Bolt (M6*45mm) 13
③
Washer 13
④
Spring Washer
(Ø16*2mm)
13
⑤
Allen Key 1
Before Beginning
Assembly:
Page 2 OF 6
Step 1
Open the carton and place all parts on a clean, non-marring surface.
Attach the Side Panels with Legs(T) to the Front and Back Panels(S) using Bolts(②), Spring Washers(④)
and Washers(③) with Allen Key(⑤) as shown above.
Do not fully tighten the Bolts.
Overview
This Table has multiple parts and may require up to 30 minutes to assemble. To give you an overview of
the Table parts, the above picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and steps before assembly.
Top Panel(R)
Side Panel with Legs(T)
Front Panel(S)
Page 3 OF 6
Step 2
Place the Top Panel(R) facedown on a clean and soft surface.
With the help of your adult partner, turn the Table Frame over and place it onto the Top Panel(R) as
shown above.
Attach the Top Panel(R) to the Front and Back Panels(S) and Side Panels with Legs(T) using Bolts(②),
Spring Washers(④) and Washers(③) with Allen Key(⑤) as shown above.
Tighten all Bolts at all joints completely at this stage.
Step 3
Use the Bolt Cap(①) to cover all Bolts.
Page 4 OF 6
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Place the Table on a level surface to check the wobbles.
If the Table wobbles, adjust the Levelers on the bottom of the Legs to make it level.
Step 5
Step 4
Page 5 OF 6
Questions & Answers about Proposition 65
• What is Proposition 65?
Proposition 65 requires businesses to provide warnings to Californians about significant
exposures to chemicals that cause cancer, birth defects or other reproductive harm. These
chemicals can be in the products that Californians purchase, in their homes or workplaces, or that
are released into the environment. By requiring that this information be provided, Proposition 65
enables Californians to make informed decisions about their exposures to these chemicals.
Proposition 65 also prohibits California businesses from knowingly discharging significant
amounts of listed chemicals into sources of drinking water.
Proposition 65 requires California to publish a list of chemicals known to cause cancer, birth
defects or other reproductive harm. This list, which must be updated at least once a year, has
grown to include approximately 900 chemicals since it was first published in 1987.
• What types of chemicals are on the Proposition 65 list?
The list contains a wide range of naturally occurring and synthetic chemicals that include
additives or ingredients in pesticides, common household products, food, drugs, dyes, or
solvents. Listed chemicals may also be used in manufacturing and construction, or they may be
byproducts of chemical processes, such as motor vehicle exhaust.
• What does a warning mean?
If a warning is placed on a product label or posted or distributed at a workplace, a business, or in
rental housing, the business issuing the warning is aware or believes that it is exposing
individuals to one or more listed chemicals.
By law, a warning must be given for listed chemicals unless the exposure is low enough to pose
no significant risk of cancer or is significantly below levels observed to cause birth defects or
other reproductive harm.
• Where can I get more information on Proposition 65?
If you have specific questions on the administration or implementation of Proposition 65, you can
contact OEHHA's Proposition 65 program at P65.Questions@oehha.ca.gov, or by phone at (916)
445-6900.
Page 6 OF 6
Loading...