LA STEELCRAFT AB-30P5 User Manual
STEELCRAFT PRODUCTS
P.O. Box 90365 - Pasadena, CA 91109
PHN 626-798-7401 FAX 626-798-1482
DO NOT SCALE DRAWING
2-3/8" OD
RIBS
1" OD HORIZ.
BRACES
MODEL
AB-30P5
BASEBALL BACKSTOP
AB30P5 ARCHED BASEBALL BACKSTOP
2-3/8" OD
FRONT BRACES
36" DIA. X 48"
DEEP CONC.
FTGS. (TYP.)
NOT SHOWN
2-7/8" OD
FRONT AND BASE
ARCHE S
FRONT OPENI NG IS 30'-0"
1" OD HORIZ.
BRACES
2-3/8" OD
RIBS
15'
5'-4 1/2"
ELEVATION VIEW
NOTE: SPECIFICATIONS ARE SUBJECT TO CHANGE
DO NOT SCALE DRAWING
DATE: 9/5/09 DRAWN BY: AFS
15'
STEELCRAFT PRODUCTS
P.O. Box 90365 - Pasadena, CA 91109
PHN 626-798-7401 FAX 626-798-1482
DO NOT SCALE DRAWING
SLEEVE FITTING
2 7/8" OD
FRONT ARCH
HORIZONTAL BRACE CONNECTION
MODEL
AB-30P5
EXTENSION DETAILS
2 3/8" OD
HORIZONTAL BRACE
SET SCREW
PARTS
ITEM QUANT DESCRIPTION
A 1 CENTER FRONT TOP S E CTION: 2-7/8" od GA LV P IPE X w/
INTERNAL F ITTINGS O N E ACH END A ND 1 S TUB F ITTINGS
WELDED AT CENTER TO RECEIVE THE CENTER VERTICAL
RIB.
B 2 LE FT AND RIGHT SIDE FRO NT A RCH TOP S ECTIONS M ADE
OF 2-7/8" OD GALV. PIPE. BOTTOM END EXTENDS INTO
FOOTING
C 2 LEF T AND RIGHT S IDE F RO NT ARCH TOP SECTIONS M ADE
OF 2-7/8" OD GALV. PIPE. BOTTOM END EXTENDS INTO
FOOTING
D 17 HORIZONTAL STIFFENE RS (B RA CE S ): 2-3/ 8" O D @ 4'-9"
GALV. PIPE.
E 42 2 -7/8" TE NSION BA NDS
F 80 2" - 9 ga. X 5 ft. WIDE CHAIN LINK FA BRIC
G 80 5/16" X 1-1/4" CC BO LT w/ LOCK NUT
H 18 10 ft . TE NSION B ARS
INSTRUCTIONS
1. INSTALL FRONT ARCH SIMILAR TO FRONT ARCH OF THE BASE BACKSTOP. THE EXTENSION
ARCH IS TO BE 5’-4 ½” IN FRONT OF THE BASE BACKSTOP.
2. INSE RT THE TOP FRONT BRACE IN THE STUB ON THE FRONT BASE ARCH AND THE
EXTENSION ARCH. TIGH TEN THE SET S CREWS.
3. THE EXTENSION BRACES ARE TO BE SPACED AT APPROXIMATEL Y 5’-6” C-C . PLACE A
BRACE BAND AT THIS SPACING TO RECEIVE THE EIGHT REMAINING FRONT BRACES.
4. PLACE THE SLIP FITTING IN EACH END OF THE FRONT BRACE AND ATTACH TO THE BRACE
BANDS USIN G HARDWARE PROVIDED. ADJUST TO MAKE THE FRONT ARCH
PERPEN DICULAR AND TIGH TEN SET SCREWS.
5. PLACE TENSION BANDS AT AP PROXIMATELY 5’-0” S PACING. PLACE T HE C HAIN L INK
FABRIC ON THE TOP OF THE EXTENSION AND ATTACH TO THE TENSION B ARS/BANDS.
NOTE: SPECIFICATIONS ARE SUBJECT TO CHANGE
DO NOT SCALE DRAWING
DATE: 9/5/09
DRAWN BY: AFS
Loading...