Page 1
IMPORTANT INSTRUCTIONS -
OPERATING MANUAL
LASKO PRODUCTS, INC.
1700 Meacham Boulevard
Fort Worth, Texas 76106
ASSEMBLY OF 12" and 16" OSCILLATING FANS
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
This Fan is for residential use only.
It is not intended to be used in commercial or industrial settings.
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons, including the following:
WHAT THIS WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.
HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for one (1) year from the date of
original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.
WHAT LASKO WILL DO: During the warranty period, Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or
replace the whole product with the same or comparable model.
WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper
handling or operation, shipping damage, abuse, misuse, unauthorized repairs made or attempted. This warranty does not cover shipping costs for the
return of products to Lasko for repair or replacement. Lasko will pay return shipping charges from Lasko following warranty repairs or replacement.
ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY),
LAST ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS
THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL LASKO’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY
INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACMENT OR REPAIR OF ANY
HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES. NOTWITHSTANDING ANYTHING TO THE CONTRARY, IN NO EVENT SHALL LASKO’S
LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY SHALL
TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD.
Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential
damages, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights. You may also have other rights which
vary from state to state and province to province.
Proof of purchase is required before a warranty claim will be accepted.
LASKO PRODUCTS, INC. LIMITED WARRANTY (NOT VALID IN MEXICO)
CUSTOMER SERVICE:
Toll-Free (800) 233-0268. Email: producthelp@laskoproducts.com
Our Customer Service team is available to assist you with product and service questions, and replacement parts. They can be reached
Monday through Friday, 8am-5pm Eastern. Please have your model number available, as well as the type and style (located on the
underside of your product). Please do not return product to place of purchase.
Customer Service Dept., 820 Lincoln Ave., West Chester, PA 19380 (Please do not send product to this location)
www.laskoproducts.com
1. Read all instructions before using Fan.
2. Make certain that the power source conforms to the electrical
requirements of the Fan.
3. Use this Fan only as described in this manual. Any other
use not recommended by the manufacturer may cause fire,
electrical shock, or injury to persons.
4. To reduce the risk of personal injury and electric shock,
the Fan should not be played with or placed where small
children can reach it.
5. Unplug power cord before installing, servicing, or moving the
Fan.
WARNING: DO NOT DEPEND UPON THE ON-OFF
SWITCH AS THE SOLE MEANS OF DISCONNECTING
POWER WHEN INSTALLING OR SERVICING THE FAN.
ALWAYS UNPLUG THE POWER CORD.
6. This Fan must NOT be used in potentially dangerous locations
such as flammable, explosive, chemical-laden or wet atmospheres.
7. DO NOT use Fan in or near a window. Rain may create an
electrical hazard.
8. Completely assemble Fan, according to instructions, before
connecting to power supply.
WARNING: THIS APPLIANCE HAS A POLARIZED
PLUG (ONE BLADE IS WIDER THAN THE OTHER). TO
REDUCE THE RISK OF ELECTRIC SHOCK, THIS PLUG IS
INTENDED TO FIT IN A POLARIZED OUTLET ONLY ONE
WAY. MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT. IF THE PLUG DOES NOT FIT FULLY INTO
THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES
NOT FIT, CONTACT A QUALIFIED ELECTRICIAN. DO NOT
ATTEMPT TO DEFEAT THIS SAFETY FEATURE.
WARNING: THIS PLUG IS A SAFETY DEVICE. TO
REDUCE THE RISK OF FIRE, SHOCK, AND PERSONAL
INJURY, DO NOT REMOVE, REPLACE, REPAIR OR
TAMPER WITH THE ORIGINALLY SUPPLIED PLUG. IF THE
FAN DOES NOT FUNCTION PROPERLY, IT MAY BE DUE
TO THE SAFETY DEVICE INCORPORATED IN THIS PLUG.
RETURN TO AN AUTHORIZED SERVICE CENTER OR
CALL 800-233-0268, MONDAY THRU FRIDAY, BETWEEN
8:00AM AND 5:00PM EST. IF THE PLUG WARNING LABEL
IS MISSING OR DAMAGED, CALL THE TOLL FREE
NUMBER FOR A REPLACEMENT LABEL.
9. Where possible, avoid the use of extension cords. If they
must be used, minimize the risk of overheating by ensuring
that they are UL listed. Never use a single extension cord
to operate more than one Fan.
10. Do not operate any Fan with a damaged cord or plug or after
the Fan malfunctions, has been dropped or damaged in any
manner.
11.Do not insert or allow fingers or foreign objects to enter any
ventilation or exhaust opening as it may cause an electric
shock or fire, or damage the Fan. Do not block or tamper
with the Fan in any manner while it is in operation.
12.Always place the Fan on a stable, flat, level surface when
operating, to avoid the chance of the Fan overturning. Locate
the Power Cord so the Fan or other objects are not resting
on it. Do not run Power Cord under carpeting. Do not cover
Power Cord with throw rugs, runners, or the like. Arrange
Power Cord away from room traffic and where it will not be
tripped over.
13.This F a n is no t intend e d f or us e i n wet o r damp
locations. Never locate a Fan where it may fall into a
bathtub or other water container.
14. Do not use Fan outdoors.
15. This Fan is not suitable for use in agricultural facilities
including areas where livestock, poultry or other animals
are confined. Please refer to National Electric Code (NEC)
Article 547-7 (2008), or applicable state or local codes or
Rev. F 10/09
SAVE THESE INSTRUCTIONS
8
2084537
Rev. F 10/09
1
2084537
Page 2
ASSEMBLY
NOTES
standards relating to electrical requirements for Agricultural
Buildings. THIS HEATER DOES NOT MEET THE REQUIRE-
MENTS OF NEC ARTICLE 547-7 (2008).
16. This Fan is not suitable for use in hazardous locations. Please
refer to National Electric Code (NEC) Article 500 or applicable
state or local codes or standards rel ating to electrical
requirements for Hazardous locations. THIS FAN DOES
NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500
(2008).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK – DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICES.
3. Fully seat Plastic Rear Grill and secure with Plastic Nut
turning CLOCKWISE. (Figure 3)
Plastic Rear
Grill
Plastic Nut
Figure 3
4. Slide Blade onto motor shaft. (Figure 4) (Align Groove on
blade hub with Pin on motor shaft. Figure 4A)
Blade
1. Tilt Fan Head back. Place Plastic Rear Grill on Motor.
(Figure 1)
Motor
Fan Head
Figure 1
Plastic Rear
Grill
2. Align tab of Plastic Rear Grill with groove on top of front
Motor cover.(Figure 2)
Plastic Rear
Grill
Motor
Figure 4
Pin
Groove
Figure 4A
Figure 2
Rev. F 10/09
2
2084537
Rev. F 10/09
7
2084537
Page 3
36
10
35
REPLACEMENT PARTS LIST
ASSEMBLY
KEY 12" OSC 16" OSC DESCRIPTION
1 2011212 2011200M Rear Grill
2098060 2098061 Parts Bag*:
11
9
8
7
16
13
14
15
21
18
19
20
25
23
22
26
27
24
34
33
32
30
31
2 2010359 2010359 Plastic Nut (Large)
3 2010058 2010059 Spinner
4 2010380L 2010380L Ornament
5 2096531I 2096529I Front Grill
6 2010008 2011013 Blade
7 2010710 2010710 Motor Cover (Front w/Threads)
8 2010661 2010661 Motor Cover (Rear)
9 02030062GL 02030066GL Motor
10 02090040 02090040 Screw Motor Cover (1)
11 2010119 2010119 Oscillation Knob
12 02090060 02090060 #7 x .080 PPH Type B Screw (2)
12
13 07091657 07091657 Threaded Spindle
2010263S 2010263S Neck Assembly **:
14 2010251 2010251 Neck Piece Bearing
15 2010276 2010276 Oscillation Link
16 2090140 2090140 Link Screw (2)
17
17 2060090 2060090 Elevation Washer
18 02090585 02090585 Elevation Spring
19 2010252S 2010252S Neck Piece
20 02090051 02090051 Neck Screw
21 2060071 2060071 Elevation Range Plate
22 02090033 02090033 Hex Nut
23 02090521 02090521 Elevation Shaft
24 02010110A 02010110A Small Adjustment Knob
25 02010109A 02010109A Large Adjustment Knob
26 2010533 2010533 Stand
27 2009224 2009224 Knob
28
28 02055087 02055087 Switch
29 2010415 2010415 Rubber Feet (4)
30 02065457 02065458 Stand Ornament
31 02090038 02090038 Screw #8 x 9/16 PPH Type 25
32 2010343 2010343 Bottom Plate (Plastic)
29
33 2060012 2060012 Bottom Plate (Metal)
34 2091145 2091145 Screw #8 x 1.5 Type A POH
35 7091854 7091854 Crimp Connect
36 02050013WB 02050013WB Power Supply Cord w/Plug
37 2084537 2084537 Instruction Sheet (Not Shown)
5. To secure Blade, screw Spinner onto Shaft
Counter Clockwise until tight on Blade hub.
(Figure 5)
16" Fan Spinner
12" Fan Spinner
Figure 5
6. Install Ornament into Metal Front Grill. Insert Tabs into
rectanglar Slots. Snap into place. (Figure 6)
Tab
Slot
Figure 6
Ornament
Side View
7. With Fan Head tilted back and centered, align Ornament of
Front Grill so it is horizontal. Insert bottom of Front Grill
into Rear Grill. Tabs at the bottom of Rear Grill should be
between two wires of Front Grill. Snap Front Grill into the
Rear Grill beginning at the top and working down both
sides. (Figure 7)
Snaps
Snaps
Ornament
Tab
Figure 7
Tab
1
Rev. F 10/09
2
6
* Parts 2-4 ordered as a Bagged Assembly
** Parts 14-21 ordered as an Assembly
3 (16")
4
3 (12")
6
5
2084537 Rev. F 10/09
3
2084537
Page 4
OPERATION
OSCILLATION: Push down oscillation knob on motor housing to make fan head move from side to side. (Figures 8
and 9)
Up: Stationary
Figure 8
Down: Oscillate
Figure 9
MAINTENANCE
WARNING: ALWAYS UNPLUG CORD BEFORE CLEAN-
ING OR DISASSEMBLING.
WARNING: DO NOT IMMERSE FAN IN WATER!
CLEANING: IMPORTANT! DO NOT immerse electrical
parts in water! Disassembled grills may be immersed
to be cleaned with a mild detergent and water. Wipe all
other parts with soft cloth moistened with water and mild
detergent only. DRY ALL PARTS COMPLETELY BEFORE
REASSEMBLING. After any maintenance or servicing,
completely reassemble unit as described in this instruction
manual before reconnecting to the power supply.
CAUTION: Do not use gasoline, benzine, thinner, harsh
cleaners, etc. as they will damage the Fan. NEVER use
ALCOHOL OR SOLVENTS.
CONVERTING FROM TABLE FAN TO WALL MOUNTED FAN
SMALL
ADJUSTMENT
KNOB
(Grills and blade removed for clarity)
MOTOR
HOUSING
NECK
STAND
LARGE
ADJUSTMENT
KNOB
(For minor adjustments)
SPEED: Control fan speed with Speed Knob. (Figure 10)
3 - High Speed
2 - Medium Speed
1 - Low Speed
Speed
Knob
Figure 10
TILTING: This Fan is equipped with a multi-angle Fan Head
for Whole-Room Air Circulation. Follow the steps below to
properly adjust the "tilt angle" of your Fan.
1. Place one hand just under the Fan Neck.
2. Place your other hand on top of Fan.
3. Gently push or pull the Fan Head until it is in the desired
position.
SERVICING: All other servicing, with the exception of general user maintenance, should be performed by an authorized service representative. Call 1-800-233-0268, Monday
through Friday, between the hours of 8:00 a.m.and 5:00 p.m.
EST for the location of your nearest service center.
LUBRICATION: Motor is permanently lubricated.
1. UNPLUG FAN FROM OUTLET.
2. Remove the Small and Large Adjustment Knobs.
1/8"
3. Tilt Motor Housing all the way back.
4. Reinstall Small Adjustment Knob and tighten.
5. Reinstall Large Adjustment Knob.
6. Install two #8 x 1 1/4" Wood Screws (not provided), using Template below, leaving 1/8" between Screwheads and wall.
7. Mount Fan over Screws using Slotted Holes on Bottom Plate.
NOTE: TO ADJUST HEAD VERTICALLY - Loosen Large Adjustment Knob, set Motor Housing, retighten Knob.
CAUTION: FAN IS UNSTABLE IN THIS POSITION AND CANNOT BE USED AS A TABLE FAN.
Rev. F 10/09
TEMPLATE - DETACH TEMPLATE AND TURN 90° for use...
NOT SUPPLIED - Two #8x1-1/4" Wood Screws (Must be purchased separately)
NOTE: BE SURE THAT THE MOUNTING SCREWS ARE INSTALLED IN A WALL STUD FOR MAXIMUM SUPPORT.
BOTTOM
TOP
7"
4
2084537
Rev. F 10/09
5
2084537
Loading...