Laserworld PRO-800RGB, PRO-1600RGB User Manual
Manual / Bedienungsanleitung /
Mode d´emploi
Proline Series
PRO-800RGB & PRO-1600RGB
Please spend a few minutes to read this manual fully
before operating this laser!
Bitte lesen Sie diese Bedienungsanleitung sorgfältig
vor Inbetriebnahme dieses Showlasersystems!
Avant d’utiliser cet appareil pour la première fois nous vous recommandons
de lire cette notice d’utilisation!
English
Deutsch
Français
02/2016
Manual: Laserworld Proline Series
Legal notice:
Thank you for purchasing this Laserworld product.
Due to continual product developments and technical improvements, Laserworld
(Switzerland) AG reserves the right to make modications to its products.
This manual and its content have been made with due care but Laserworld (Switzerland) AG
cannot however, take any responsibility for any errors, omissions or any resulting damages
forthwith.
The brands and product names mentioned in this manual are trade marks or registered trade
marks of their respective owners.
Rechtlicher Hinweis:
Die Firma Laserworld (Switzerland) AG behält sich das Recht vor, Änderungen an ihren Produkten vorzunehmen, die der technischen Weiterentwicklung dienen. Diese Änderungen werden
nicht notwendigerweise in jedem Einzelfall dokumentiert.
Diese Betriebsanleitung und die darin enthaltenen Informationen wurden mit der gebotenen
Sorgfalt zusammengestellt. Die Firma Laserworld (Switzerland) AG übernimmt jedoch keine
Gewähr für Druckfehler, andere Fehler oder daraus entstehende Schäden.
Die in dieser Bedienungsanleitung genannten Marken und Produktnamen sind Warenzeichen
oder eingetragene Warenzeichen der jeweiligen Titelhalter.
Information juridique :
L’entreprise Laserworld (Switzerland) AG se réserve le droit d’eectuer des modications concernant leurs produits et ainsi de répondre au développement technique. Ces modications
ne seront pas nécessairement annoncées en tout cas spécique. Ce mode d’emploi et les informations contenues dedans ont été établis avec le soin minutieux qui s’impose dans ce cas.
Laserworld (Switzerland) AG ne pourra pas être tenue responsable pour d’éventuelles erreurs
d’impression ou dommages en résultants.
En cas de doutes, veuillez toujours contacter Laserworld (Switzerland) AG . Les noms de
marques et de produits utilisés dans ce mode d’emploi sont des marques de fabrique ou des
marques déposées.
L’utilisation est réservée à un usage professionnel selon décret n°2007-665 du 2 mai
2007 relatif à la sécurité des appareils à laser sortant!
Article 4 bis :
« Les usages spéciques autorisés pour les appareils à laser sortant d’une classe supérieure à 2
sont les usages professionnels suivants :
(…)
9° Spectacle et achage :
Toutes les applications de trajectoire, de visualisation, de projection ou de reproduction
d’images en deux ou trois dimensions. »
page 2 / 36
Manual: Laserworld Proline Series
Content:
1. Product and package contents
2. Preliminary warning notices
3. Initial operations, safety instructions
4. Working on the device
5. Service notes
6. Warnings and other notices on the device
7. Device connections
8. Operation
Final statement
Technical data sheet
Laser specications
page 3 / 36
Manual: Laserworld Proline Series
1. Product and package contents
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector 1 x Interlock connector
1 x power cable 2 x keys
1 x remote control unit 1 x SD card
1 x manual
(for key switch)
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels,
power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of damage to the
eyes or even blindness in extreme circumstances!
4. Do not operate the device at high humidity, in the rain or in dusty environments.
5. Protect device against dripping or splashing water. Do not place any liquid lled
containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered
with in any way.
3. Initial operations, safety instructions
1. Make sure to use correct voltage; see information on device & in this manual.
2. Make sure that the device is not connec-
ted to mains during installation.
3. Installation has to be done by technical
experienced and qualied persons according to safety regulations of the respective country.
4. Always ensure that maximum permissible exposure (MPE) is not exceeded
in areas accessible to the public or
members of sta.
5. In some countries an additional inspection by technical control institutes
could be necessary.
page 4 / 36
6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.
7. The power supply should be easily accessible.
8. When installing the laser mount it with
a minimum distance of 15 cm from walls
and objects.
9. For safe setup e.g. on walls or ceilings
please use a safety cord. The safety cord
should be able to withstand tenfold the
weight of the device. Please follow the
accident prevention regulations of professional associations and/or comparable
regulations for accident prevention.
Manual: Laserworld Proline Series
10. If the device has been exposed to great
temperature changes, do not switch it
on immediately. Condensation (or any
moisture/water formed) may damage
this device.
11. Never use dimmer, RC or other electronically switched sockets. Whenever
possible, do not use the laser projector
together with large appliances (especially fog machines) on the same mains!
12. Ensure sucient ventilation and do not
place the device on any warm or heat radiating surface. Especially the ventilati-
on openings must not be covered!
13. Ensure that device does not get over-
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a degradation of performance.
14. This unit is intended for indoor use only.
4. Working on the device
1. This product has no user serviceable parts inside and should only
be maintained and serviced by a qualied engineer.
2. Be sure that the mains plug is not connected to the power
supply while installing or opening the device (e.g. for
cleaning).
3. Take o all reecting things like rings, watches etc.
before starting to work with or at the projector.
4. Only use non-reecting tools to work on device.
5. Wear protective clothing (like goggles, gloves etc.) according to laser power and wavelength of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
• Quick on/o switching of this device will
reduce durability of the laser diode dramatically.
• Avoid sharp knocks and shocks to this
device and ensure sucient protection
during transportation. Look after your Laserworld product.
• To increase durability of your laser,
protect device against overheating:
page 5 / 36
• Always ensure sucient ventilation.
• Do not face spotlights (especially mo-
ving heads) to the device.
• Check temperature after approx. 30
minutes with each new installation. If
necessary install the projector at a place
with dierent temperature.
• Keep the device dry. Protect it from
moisture, rain and damp.
• Switch o device when it is not needed.
Diodes are switched on and can wear out
even if there is no visible laser output.
Manual: Laserworld Proline Series
• Please ensure the fans and heatsinks are
• Removal of the warranty label as well
clear from dust and debris otherwise the
risk of overheating may occur. If the unit
and airways appear to be blocked then
please contact a qualied service engineer to maintain and service the product.
• The devices of Ecoline, Evolution, Club
and Proline Series are not meant for professional applications. After approx. one
hour of operation, the device should cool
down for about 15 minutes.
6. Warnings and other notices on the device
Please read manual before operation
Laser radiation!
Avoid exposure
to beam.
Laser class 4
Caution of
radiation if cover
is removed
Use in enclosed spaces only!
as damages to the device caused by
improper handling, neglect of the safety instructions and service notes will
void the warranty.
Model type
Production
year
Wavelength
Output power
Power supply
& consumption
page 6 / 36
Manual: Laserworld Proline Series
7. Device connections
Front side
laser outlet
IR receiver
Rear side
loop for
safety cord
DMX in
DMX out
ILDA in
ILDA out
microphone
for sound
to light
operation
page 7 / 36
key switch fan
Interlock
LCD Display
menu settings
Power
button
power
connection
Scan safety switch
SD card slot
Manual: Laserworld Proline Series
8. Operation
1. Connect the power cable to the device and then to the mains
2. Insert key and turn it „on“
3. Press the „on/o“ switch on. The „on/o“ switch shines green now. Attention! The pro-
jector may emit laser beams immediately.
4. Mode selection:
Please use the push buttons below the LCD display to select the dierent modes
Menu
Browse the Menu
Auto mode:
Push the Menu button until MODE: AUTO is displayed. Press the ‚UP‘ and/or ‚DOWN‘
buttons to browse the mode and press ‚ENTER‘ to select the desired program.
Music mode:
Push the Menu button until MODE: MUSIC is displayed. Press the ‚UP‘ and/or ‚DOWN‘
buttons to browse the mode and press ‚ENTER‘ to select the desired program.
LCD Display
Enter
Control the sensitivity of the microphone by pushing the Menu button until MODE:
SETTING is displayed. Press the ‚UP‘ until MODE: SETTING - MUSIC is displayed
and the ‚UP‘ and/or ‚DOWN‘ buttons to set the sensitivity of the microphone. Press
‚ENTER‘.
DMX mode:
Push the Menu button until MODE: DMX is displayed. Press the ‚UP‘ and/or ‚DOWN‘
buttons to set the DMX address and press ‚ENTER‘.
Connect a DMX controller to operate the laser.
The laser uses 16 DMX channels, so make sure that the next device uses an address that
doesn’t overlap with this range.
page 8 / 36
Manual: Laserworld Proline Series
Channel Value Function
1 - modes 0 - 9 laser o
10 - 49 sound mode
50 - 149 automatic mode
150 - 199 static DMX mode
200 - 255 DMX animation
Attention! The following channels only work if the laser is in DMX animation mode (Channel 1 at value 200 - 255)!
2 - pattern selection 0 - 255 pattern selection
3 - grating 0 - 49 no grating
50 - 99 burst grating
100 - 149 line grating
150 - 199 3D grating
200 - 255 3D line grating
4 - colors 0 - 16 white
17 - 33 red
34 - 50 green
51 - 67 blue
68 - 84 yellow
85 - 101 purple
102 - 118 turquoise
119 - 169 rainbow color mixing (static)
170 - 220 rainbow color mixing (moving)
221 - 237 red
238 - 255 rainbow color mixing (static)
5 - red color fading 0 - 255 red color fading
6 - green color fading 0 - 255 green color fading
7 - blue color fading 0 - 255 blue color fading
8 - horizontal movement 0 - 125 manual positioning
126 - 155 left to right movement with increasing speed
156 - 245 right to left movement with increasing speed
246 - 255 automatic positioning
9 - vertical movement 0 - 125 manual positioning
126 - 155 top to bottom movement with increasing speed
156 - 245 bottom up movement with increasing speed
246 - 255 automatic positioning
page 9 / 36
Manual: Laserworld Proline Series
Channel Value Function
10 - zoom 0 - 10 no zoom
11 - 87 manual zoom
88 - 150 automatic zoom in with increasing speed
151 - 200 automatic zoom out with increasing speed
201 - 255 automatic zoom in and out (in turns)
11 - X rotation 0 - 128 manual positioning
129 - 255 automatic movement
12 - Y rotation 0 - 128 manual positioning
129 - 255 automatic movement
13 - Z rotation 0 - 128 manual positioning
129 - 192 anticlockwise movement with increasing speed
193 - 255 clockwise movement with increasing speed
14 - drawing 0 - 74 manual drawing
75 - 104 automatic drawing with increasing speed
105 - 144 automatic reduction with increasing speed
145 - 184 automatic drawing and reduction with increa-
sing speed
185 - 255 automatic two-sided reduction
15 - Y wave 0 - 10 no eect
11 - 69 small wave eect with increasing speed
70 - 129 medium wave eect with increasing speed
130 - 189 large wave eect with increasing speed
190 - 255 wave eect II
15 - X wave 0 - 10 no eect
11 - 69 small wave eect with increasing speed
70 - 129 medium wave eect with increasing speed
130 - 189 large wave eect with increasing speed
190 - 255 wave eect II
Attention! The following channel only work if the laser is in static DMX mode (Channel 1 at value 150 - 199)!
2 - pattern selection 0 - 255 pattern selection
Please note that not each pattern can be combined with each eect.
To use the grating eects in ILDA mode, additional DMX control is necessary.
page 10 / 36
Manual: Laserworld Proline Series
SD card:
This show laser system has an integrated SD card slot (a 2 GB SD card is included in the
delivery). It allows saving patterns, animations or shows as .ILD les on the SD card and
running them at the projector.
Insert the SD card into the card slot. Push the Menu button until MODE: SD PRG is
displayed. Press the ‚UP‘ and/or ‚DOWN‘ buttons to browse the mode and press ‚ENTER‘
to select the desired program.
Information about the preset frames and animations on this SD Card
Certain frames and animations were created using Pangolin‘s Lasershow Designer
software, and Pangolin has granted us permission to include these with this projector.
To create similar content, check out Pangolin‘s QuickShow software, which is available
through Laserworld as an ocial distribution partner.
Go to http://www.laserworld.com/quickshow for more information.
Due to copyright regulations it is not permitted to copy any fames or animations from
this SD-card for other use. The copyright remains with their respective owner.
Master-Slave-Mode:
To use the daisy chain / Master-Slave-Mode connect two (or more) laser projectors of
the same series via DMX cables:
Master projector (DMX out) -> DMX cable -> slave projector 1 (DMX in) ;
slave projector 1 (DMX out) -> DMX cable -> slave projector 2 ...etc.
DMX cable Slave projectorMaster projector
Select auto or
music mode at the
master projector
(see above)
Push the Menu button until
MODE: SLAVE is displayed
and press ‚ENTER‘ to select the
slave mode.
ILDA control:
Connect your device („ILDA IN“) via an ILDA cable to an interface / controller. Use a laser
control software, e.g. Phoenix or Pangolin, to run the device. Use „ILDA OUT“ to connect
it to another device.
Settings:
Push the Menu button until MODE: SETTING is displayed. Press the ‚UP‘ and/or
‚DOWN‘ buttons to browse the setting which has to be changed (e.g. color, speed, etc.)
and press ‚ENTER‘ to select the setting. Press ‚ENTER‘ again to save the new setting.
page 11 / 36
Loading...