Laserworld EL-230RGB operation manual

Manual / Bedienungsanleitung

/ Mode d´emploi

Ecoline Series

EL-230RGB

Please spend a few minutes to read this manual fully

before operating this laser!

Bitte lesen Sie diese Bedienungsanleitung sorgfältig

vor Inbetriebnahme dieses Showlasersystems!

Avant d’utiliser cet appareil pour la première fois nous vous recommandons

de lire cette notice d’utilisation!

English

Deutsch

Français

12/2017

Legal notice:

Thank you for purchasing this Laserworld
product. Due to continual product developments and technical improvements, La­serworld (Switzerland) AG reserves the right to make modications to its products.
This manual and its content have been made with due care but Laserworld (Swit­zerland) AG cannot however, take any responsibility for any errors, omissions or any
resulting damages forthwith. The brands and product names mentioned in this ma­nual are trade marks or registered trade marks of their respective owners.

Rechtlicher Hinweis:

Die Firma Laserworld (Switzerland) AG behält sich das Recht vor, Änderungen an
ihren Produkten vorzunehmen, die der technischen Weiterentwicklung dienen.
Diese Änderungen werden nicht notwendigerweise in jedem Einzelfall dokumen­tiert. Diese Betriebsanleitung und die darin enthaltenen Informationen wurden
mit der gebotenen Sorgfalt zusammengestellt. Die Firma Laserworld (Switzerland)
AG übernimmt jedoch keine Gewähr für Druckfehler, andere Fehler oder daraus
entstehende Schäden. Die in dieser Bedienungsanleitung genannten Marken und
Produktnamen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen
Titelhalter.

Content:

1. Product and package contents

2. Preliminary warning notices

3. Initial operations, safety instructions

4. Working on the device

5. Service notes

6. Warnings and other notices on the device

7. Device connections

8. Operation

Information juridique :

L’entreprise Laserworld (Switzerland) AG se réserve le droit d’eectuer des modica­tions concernant leurs produits et ainsi de répondre au développement technique.
Ces modications ne seront pas nécessairement annoncées en tout cas spécique.
Ce mode d’emploi et les informations contenues dedans ont été établis avec le soin
minutieux qui s’impose dans ce cas.
Laserworld (Switzerland) AG ne pourra pas être tenue responsable pour
d’éventuelles erreurs d’impression ou dommages en résultants.
En cas de doutes, veuillez toujours contacter Laserworld (Switzerland) AG . Les noms
de marques et de produits utilisés dans ce mode d’emploi sont des marques de
fabrique ou des marques déposées.

L’utilisation est réservée à un usage professionnel selon décret n°2007-665 du
2 mai 2007 relatif à la sécurité des appareils à laser sortant!

Article 4 bis :

« Les usages spéciques autorisés pour les appareils à laser sortant d’une classe su­périeure à 2 sont les usages professionnels suivants :
(…)
9° Spectacle et achage :
Toutes les applications de trajectoire, de visualisation, de projection ou de repro­duction d’images en deux ou trois dimensions. »

Final statement

Technical data sheet

Laser specications

1. Product and package contents

Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector 1 x manual 2 x key
1 x power cable 1 x Interlock Connector

2. Preliminary warning notices

1. Please use this device only according to these operating instructions.

2. Do not use the device if there are any visible damages on housing, connector
panels, power supplies or power cords.

3. Never look directly into the light source of a laser projector. Danger of dama-
ge to the eyes or even blindness in extreme circumstances!

4. Do not operate the device at high humidity, rain or in dusty surroundings.

5. Protect device against dripping or splashing water. Do not place any liquid
lled containers near to this device.

Any warranty claims are void if the warranty label is removed or tampered

with in any way.

3. Initial operations, safety instructions

1. Make sure to use correct voltage;
see information on device & in this
manual.

2. Make sure that the device is not
connected to mains during ins­tallation.

3. Installation has to be done by

technical experienced and qua­lied persons according to safe-

ty regulations of the respective
country.

4. Always ensure that maximum
permissible exposure (MPE) is not
exceeded in areas accessible to the
public or members of sta.

5. In some countries an additional
inspection by technical control in-

stitutes could be necessary.

6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.

7. The power supply should be easily
accessible.

8. When installing the laser keep
mount it with a minimum distance
of 15 cm from walls and objects.

9. For safe setup e.g. on walls or
ceilings please use a safety cord.
The safety cord should be able to
withstand tenfold the weight of
the device. Please follow the ac­cident prevention regulations of
professional associations and/or
comparable regulations for acci-

dent prevention.

10. If the device has been exposed to
great temperature changes, do
not switch it on immediately. Con­densation (or any moisture/water
formed) may damage device.

11. Never use dimmer, RC or other
electronically switched sockets.
Whenever possible, do not use the
laser projector together with large
appliances (especially fog machi­nes) on the same mains!

12. Ensure sucient ventilation and

do not place the device on any
warm or heat radiating surface. Es­pecially the ventilation openings
must not be covered!

13. Ensure that device does not gets
overheated. Make sure that the
device is not exposed to spotlights
(especially moving heads). Heat of
spotlights could overheat laser in a
little while and leads to a degrada­tion of performance.

14. This unit is intended for indoor use
only.

4. Working on the device

1. This product has no user serviceable parts inside and
should only be maintained and serviced by a qua-
lied engineer.

2. Be sure that the mains plug is not connected
to the power supply while installing or opening
the device (e.g. for cleaning).

3. Take o all reecting things like rings, watches etc. before
start working with or at the projector.

4. Use only non-reecting tools to work on device.

5. Wear protective clothing (like goggles, gloves etc.) according to laser power
and wavelength of the laser.

5. Service notes

• Moisture and heat can reduce lifetime of the laser system dramatically and
expires any warranty claim.

• Quick on/o switching of this device will reduce durability of the laser diode
dramatically.

• Avoid sharp knocks and shocks to this device and ensure sucient protection
during transportation. Look after your Laserworld product.

• To increase durability of your laser, protect device against overheating:

- Always ensure sucient ventilation.

- Do not face spotlights (especially
moving heads) to the device.

- Check temperature after approx.
30 minutes with each new ins­tallation. If necessary install the
projector at a place with dierent
temperature.

- Switch o device when it is not
needed. Diodes are switched on
and can wear out even if there is
no visible laser output.

- Keep the device dry. Protect it
from moisture, rain and damp.

• The devices of Ecoline, Evolution,
Club and Proline Series are not
meant for professional applica-

operation, the device should cool
down for about 15 minutes.

• Please ensure the fans and
heatsinks are clear from dust and
debris otherwise the risk of over­heating may occur. If the unit and
airways appear to be blocked then
please contact a qualied service
engineer to maintain and service
the product.

• Removal of the warranty label
as well as damages to the device
caused by improper handling,
neglect of the safety instruc­tions and service notes will void
the warranty.

tions. After approx. one hour of

6. Warnings and other notices on the device

7. Device connections

Laser aperture
warning label

DMX address,
operation mode

LED:
Sound sensitivity

microphone

LED:
Laser emission

trim pot for
music-sensitivity

ON/OFF switch

mains connection

Laser radiation!

Avoid exposure

to beam

Laser class 3B

Caution of ra-

diation if cover

is removed

Use in enclosed spaces only!

Model type

Production year

Wavelength

Output power

Power supply

& consumption

DMX out DMX in

Interlock

key switch

8. Operation

a. Connect the power cable to the device and then to the mains
b. Insert the key into the key switch and turn it „ON“
c. Connect the Interlock Connector with the Interlock interface
d. Press „ON“ to switch the device on

8.1. Automatic, Stand-alone operation

Set the device to auto mode:

8.2. Music mode, Sound-to-light operation

Your device runs in music mode:

Control the music-sensitivity with the trim pot at the back panel. The LED is as­hing when the device is triggered.

8.3. DMX-512 mode

Switch 10 must be set to „o“, the other switches are used for setting the DMX
address:

Channel Value Function

7 0 - 255 Zoom / size

8 0- 255 Color

9 above 200 Reset

10 1 - 255 Rotate x axis

11 1 - 255 Rotate y axis

12 1 - 255 Rotate z axis

Please note that a pattern can not necessarily be combined with each eect.

8.4. Turn laser o

Connect a DMX controller to operate the laser.
Use the switches 1 - 9 to set the DMX address of the laser. Each switch represents a
number. To dene a number use the preceding number and multiply it by 2:

Switch 1 2 3 4 5 6 7 8 9 10

Number 1 2 4 8 16 32 64 128 256 Mode Switch

The laser uses 12 DMX channels, so make sure that the next device uses an address
that doesn’t overlap with this range.

Channel Value Function

1 0 - 69 Laser o

70 - 139 Sound mode

140 - 209 Automatic mode

210 - 255 DMX mode

2 0 - 255 Pattern selection

3 0 - 255 Strobe eect

4 0 - 255 Point speed

5 0 - 255 x axis positioning

6 0 - 255 y axis positioning

To turn o the device switch it o („OFF“), switch the key to „OFF“ and disconnect
the power cable from the mains.

Final statement

Laserworld products are tested and product packaging is inspected before leaving
our warehouse. Users must to follow the local safety regulations and warnings
within this manual and adhere to any regulations within its place of use. Damages
through inappropriate use will void any liability or warranty of our products. Due to
continual product developments, please check for the latest update of this product
manual at www.laserworld.com. If you do have any further questions, then please
contact your dealer/place of purchase or use our contact section on our website.
For service issues, please contact your dealer/place of purchase and ensure only
genuine Laserworld spare parts are used in any service repairs.

Errors and omissions excepted and products are subject to change.

Laserworld (Switzerland) AG

Kreuzlingerstrasse 5
8574 Lengwil
SWITZERLAND

Registered oce:
8574 Lengwil / Switzerland
Company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
CEO: Martin Werner
VAT no. (Switzerland): 683 180
UID (Switzerland): CHE-113.954.889
VAT no. (Germany): DE258030001
WEEE-Reg.-No. (Germany): DE 90759352

www.laserworld.com
[e-mail]

representative according to EMVG:
Ray Technologies GmbH
Managing Director: Martin Werner
Mühlbachweg 2
83626 Valley / Germany