Laserworld EL-200RGB operation manual
Manual / Bedienungsanleitung /
Mode d´emploi
Ecoline Series
EL-200RGB
Please spend a few minutes to read this manual fully
before operating this laser!
Bitte lesen Sie diese Bedienungsanleitung sorgfältig
vor Inbetriebnahme dieses Showlasersystems!
Avant d’utiliser cet appareil pour la première fois nous vous recommandons
de lire cette notice d’utilisation!
English
Deutsch
Français
12/2017
Manual: Ecoline Series EL-200RGB
Legal notice:
Thank you for purchasing this Laserworld product. Due to continual product developments
and technical improvements, Laserworld (Switzerland) AG reserves the right to make modications to its products.
This manual and its content have been made with due care but Laserworld (Switzerland) AG
cannot however, take any responsibility for any errors, omissions or any resulting damages
forthwith.
The brands and product names mentioned in this manual are trade marks or registered trade
marks of their respective owners.
Rechtlicher Hinweis:
Die Firma Laserworld AG behält sich das Recht vor, Änderungen an ihren Produkten vorzunehmen, die der technischen Weiterentwicklung dienen. Diese Änderungen werden nicht
notwendigerweise in jedem Einzelfall dokumentiert.
Diese Betriebsanleitung und die darin enthaltenen Informationen wurden mit der gebotenen Sorgfalt zusammengestellt. Die Firma Laserworld AG übernimmt jedoch keine Gewähr für
Druckfehler, andere Fehler oder daraus entstehende Schäden.
Die in dieser Bedienungsanleitung genannten Marken und Produktnamen sind Warenzeichen
oder eingetragene Warenzeichen der jeweiligen Titelhalter.
Information juridique :
L’entreprise Laserworld (Switzerland) AG se réserve le droit d’eectuer des modications concernant leurs produits et ainsi de répondre au développement technique. Ces modications
ne seront pas nécessairement annoncées en tout cas spécique. Ce mode d’emploi et les informations contenues dedans ont été établis avec le soin minutieux qui s’impose dans ce cas.
Laserworld (Switzerland) AG ne pourra pas être tenue responsable pour d’éventuelles erreurs
d’impression ou dommages en résultants.
En cas de doutes, veuillez toujours contacter Laserworld (Switzerland) AG . Les noms de
marques et de produits utilisés dans ce mode d’emploi sont des marques de fabrique ou des
marques déposées.
L’utilisation est réservée à un usage professionnel selon décret n°2007-665 du 2 mai
2007 relatif à la sécurité des appareils à laser sortant!
Article 4 bis :
« Les usages spéciques autorisés pour les appareils à laser sortant d’une classe supérieure à 2
sont les usages professionnels suivants :
(…)
9° Spectacle et achage :
Toutes les applications de trajectoire, de visualisation, de projection ou de reproduction
d’images en deux ou trois dimensions. »
page 2 / 28
Manual: Ecoline Series EL-200RGB
Content:
1. Product and package contents
2. Preliminary warning notices
3. Initial operations, safety instructions
4. Working on the device
5. Service notes
6. Warnings and other notices on the device
7. Device connections
8. Operation
Final statement
Technical data sheet
Laser specications
page 3 / 28
Manual: Ecoline Series EL-200RGB
1. Scope of delivery & details
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector 1 x manual 1 x Interlock
1 x power cable 2 x key
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector panels,
power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of damage to the
eyes or even blindness in extreme circumstances!
4. Do not operate the device at high humidity, in the rain or in dusty environments.
5. Protect device against dripping or splashing water. Do not place any liquid lled
containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered
with in any way.
3. Initial operations, safety instructions
1. Make sure to use correct voltage; see information on device & in this manual.
2. Make sure that the device is not connec-
ted to mains during installation.
3. Installation has to be done by technical
experienced and qualied persons according to safety regulations of the respective country.
4. Always ensure that maximum permissible exposure (MPE) is not exceeded in areas accessible to the public or members of
sta.
5. In some countries an additional inspection by technical control institutes
could be necessary.
6. Connect an easily accessible inter-
page 4 / 28
lock connector or circuit breaker
to the projector.
7. The power supply should be easily accessible.
8. When installing the laser mount it with
a minimum distance of 15 cm from walls
and objects.
9. For safe setup e.g. on walls or ceilings
please use a safety cord. The safety cord
should be able to withstand tenfold the
weight of the device. Please follow the
accident prevention regulations of professional associations and/or comparable
regulations for accident prevention.
10. If the device has been exposed to great
temperature changes, do not switch it
on immediately. Condensation (or any
Manual: Ecoline Series EL-200RGB
moisture/water formed) may damage
device.
11. Never use dimmer, RC or other electronically switched sockets. Whenever possible, do not use the laser projector together
with large appliances (especially fog machines) on the same mains!
12. Ensure sucient ventilation and do not
place the device on any warm or heat ra-
diating surface. Especially the ventilati-
on openings must not be covered!
13. Ensure that device does not get over-
heated. Make sure that the device is not
exposed to spotlights (especially moving
heads). Heat of spotlights could overheat
laser in a little while and leads to a degradation of performance.
14. This unit is intended for indoor use only.
4. Working on the device
1. This product has no user serviceable parts inside and should only be
maintained and serviced by a qualied engineer
2. Be sure that the mains plug is not connected to the power supply while installing or opening the device (e.g. for cleaning).
3. Take o all reecting things like rings, watches etc. before
starting to work with or at the projector.
4. Only use non-reecting tools to work on device.
5. Wear protective clothing (like goggles, gloves etc.)
according to laser power and wavelength of the laser.
5. Service notes
• Moisture and heat can reduce lifetime of
the laser system dramatically and expires
any warranty claim.
• Quick on/o switching of this device will
reduce durability of the laser diode dramatically.
• Avoid sharp knocks and shocks to this
device and ensure sucient protection
during transportation. Look after your Laserworld product.
• To increase durability of your laser,
protect device against overheating:
page 5 / 28
- Always ensure sucient ventilation.
- Do not face spotlights (especially moving heads) to the device.
- Check temperature after approx. 30
minutes with each new installation.
If necessary install the projector at a
place with dierent temperature.
- Keep the device dry. Protect it from
moisture, rain and damp.
- Switch o device when it is not needed. Diodes are switched on and can
wear out even if there is no visible laser output.
Manual: Ecoline Series EL-200RGB
• The devices of Ecoline, Evolution, Club
and Proline Series are not meant for professional applications. After approx. one
hour of operation, the device should cool
down for about 15 minutes.
• Removal of the warranty label as well
• Please ensure the fans and heatsinks are
clear from dust and debris otherwise the
risk of overheating may occur. If the unit
6. Warnings and other notices on the device
Please read manual before operation
Laser radiation!
Avoid exposure
to beam.
Laser class 3B
Caution of
radiation if cover
is removed
Use in enclosed spaces only!
and airways appear to be blocked then
please contact a qualied service engineer to maintain and service the product.
as damages to the device caused by
improper handling, neglect of the safety instructions and service notes will
void the warranty.
Model type
Production
year
Wavelength
Output power
Power supply
& consumption
7. Device connections
Interlock
DMX out DMX in
page 6 / 28
DMX address
key switch
power switch
connection for power supply
Manual: Ecoline Series EL-200RGB
8. Operation
1. Connect the power cable to the device and then to the mains
2. Insert key and turn it ‚ON‘. Then press ‚ON‘ to switch the device on
3. Please make sure, that the Interlock adapter is inserted
4. Your device runs in auto mode:
5. Your device runs in music mode:
Microphone &
Sensitivity
Control the music-sensitivity by the trim pot at the front side of the device. The LED is
ashing when the device is triggered.
6. Your device runs in DMX mode if ‘10‘ is switched o:
Connect a DMX controller to operate the laser.
Use the switches 1 - 9 to set the DMX address of the laser. Each switch represents a number. To dene a number use the preceding number and multiply it by 2:
Switch 1 2 3 4 5 6 7 8 9 10
Number 1 2 4 8 16 32 64 128 256 Mode Switch
page 7 / 28
Manual: Ecoline Series EL-200RGB
The laser uses 11 DMX channels, so make sure that the next device uses an address that
doesn’t overlap with this range.
Channel Value Function
1 0 - 70 Laser o
71 - 142 Sound mode
143 - 214 Automatic mode
215 - 255 DMX mode
2 0 - 255 Pattern selection
3 0 - 255 Animation (not with all patterns); strobe eect
4 0 - 255 Display mode
5 0 - 255 Horizontal movement
6 0 - 255 Vertical movement
7 0 - 255 Zoom
8 0 - 32 Red, green and blue
33 - 64 Green and blue
65 - 97 Red and blue
98 - 130 Red and green
131 - 162 Blue
163 - 195 Red
196 - 228 Green
229 - 255 Audio controls color change
9 0 - 255 Rotation x-Axis
10 0 - 255 Rotation Y-Axis
11 0 - 255 Rotation
Please note that not each pattern can be combined with each eect.
7. To turn o the device switch it o („OFF“), switch the key to ‚OFF‘ and disconnect the
power cable from the mains.
page 8 / 28
Manual: Ecoline Series EL-200RGB
Final statement
Laserworld products are tested and product packaging is inspected before leaving our
warehouse.
Users must to follow the local safety regulations and warnings within this manual and adhere
to any regulations within its place of use. Damages through inappropriate use will void any
liability or warranty of our products.
Due to continual product developments, please check for the latest update of this product
manual at www.laserworld.com. If you do have any further questions, then please contact
your dealer/place of purchase or use our contact section on our website.
For service issues, please contact your dealer/place of purchase and ensure only genuine
Laserworld spare parts are used in any service repairs.
Errors and Omissions excepted and products are subject to change.
Laserworld (Switzerland) AG
Kreuzlingerstrasse 5
8574 Lengwil-Oberhofen
SWITZERLAND
Registered oce:
8574 Lengwil-Oberhofen / Switzerland
Company number: CH-440.3.020.548-6
Commercial Registry Kanton Thurgau
CEO: Martin Werner
VAT no. (Switzerland): 683 180
UID (Switzerland): CHE-113.954.889
VAT no. (Germany): DE258030001
WEEE-Reg.-No. (Germany): DE 90759352
www.laserworld.com
info@laserworld.com
representative according to EMVG:
Ray Technologies GmbH
Managing Director: Martin Werner
Mühlbachweg 2
83626 Valley / Germany
page 9 / 28
Loading...