Laserworld CS-1000RGB, CS-2000RGB operation manual
Manual / Bedienungsanleitung /
Mode d´emploi
Club Series
CS-1000RGB
CS-2000RGB
Please spend a few minutes to read this manual fully
Bitte lesen Sie diese Bedienungsanleitung sorgfältig
Avant d’utiliser cet appareil pour la première fois nous vous recomman-
before operating this laser!
vor Inbetriebnahme dieses Showlasersystems!
dons de lire cette notice d’utilisation!
English
Deutsch
Français
12/2017
Manual: Club Series
Legal notice:
Thank you for purchasing this Laserworld product.
Due to continual product developments and technical improvements,
Laserworld (Switzerland) AG reserves the right to make modications to its products.
This manual and its content have been made with due care but Laserworld (Switzerland) AG
cannot however, take any responsibility for any errors, omissions or any resulting damages
forthwith.
The brands and product names mentioned in this manual are trade marks or registered
trade marks of their respective owners.
Rechtlicher Hinweis:
Die Firma Laserworld (Switzerland) AG behält sich das Recht vor, Änderungen an ihren Produkten vorzunehmen, die der technischen Weiterentwicklung dienen. Diese Änderungen
werden nicht notwendigerweise in jedem Einzelfall dokumentiert.
Diese Betriebsanleitung und die darin enthaltenen Informationen wurden mit der gebotenen Sorgfalt zusammengestellt. Die Firma Laserworld (Switzerland) AG übernimmt jedoch
keine Gewähr für Druckfehler, andere Fehler oder daraus entstehende Schäden.
Die in dieser Bedienungsanleitung genannten Marken und Produktnamen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Titelhalter.
Information juridique :
L’entreprise Laserworld (Switzerland) AG se réserve le droit d’eectuer des modications
concernant leurs produits et ainsi de répondre au développement technique. Ces modications ne seront pas nécessairement annoncées en tout cas spécique. Ce mode d’emploi
et les informations contenues dedans ont été établis avec le soin minutieux qui s’impose
dans ce cas.
Laserworld (Switzerland) AG ne pourra pas être tenue responsable pour d’éventuelles erreurs d’impression ou dommages en résultants.
En cas de doutes, veuillez toujours contacter Laserworld (Switzerland) AG . Les noms de
marques et de produits utilisés dans ce mode d’emploi sont des marques de fabrique ou
des marques déposées.
L’utilisation est réservée à un usage professionnel selon décret n°2007-665 du 2 mai
2007 relatif à la sécurité des appareils à laser sortant!
Article 4 bis :
« Les usages spéciques autorisés pour les appareils à laser sortant d’une classe supérieure
à 2 sont les usages professionnels suivants :
(…)
9° Spectacle et achage :
Toutes les applications de trajectoire, de visualisation, de projection ou de reproduction
d’images en deux ou trois dimensions. »
EN page 1 / 12
Manual: Club Series
Content:
1. Product and package contents
2. Preliminary warning notices
3. Initial operations, safety instructions
4. Working on the device
5. Service notes
6. Warnings and other notices on the device
7. Device connections
8. Operation
Final statement
Technical data sheet
Laser specications
page 2 / 12 EN
Manual: Club Series
1. Product and package contents
Please check if all listed parts are included and undamaged. Included in delivery:
1 x laser projector 1 x Interlock connector (already attached)
1 x power cable 1 x key (for key switch)
1 x manual
2. Preliminary warning notices
1. Please use this device only according to these operating instructions.
2. Do not use the device if there are any visible damages on housing, connector
panels, power supplies or power cords.
3. Never look directly into the light source of a laser projector. Danger of dama-
ge to the eyes or even blindness in extreme circumstances!
4. Do not operate the device at high humidity, in the rain or in dusty
environments.
5. Protect device against dripping or splashing water. Do not place any liquid lled
containers near to this device.
Any warranty claims are void if the warranty label is removed or tampered
3.
Initial operations, safety instructions
with in any way.
1. Make sure to use correct voltage;
see information on device & in this
manual.
2. Make sure that the device is not
connected to mains during installation.
3. Installation has to be done by
technical experienced and qualied persons according to safe-
ty regulations of the respective
country.
EN page 3 / 12
4. Always ensure that maximum
permissible exposure (MPE) is
not exceeded in areas accessible to the public or members of
sta.
5. In some countries an additional inspection by technical control institutes
could be necessary.
6. Connect an easily accessible inter-
lock connector or circuit breaker
to the projector.
Manual: Club Series
7. The power supply should be easily
accessible.
8. When installing the laser mount it
with a minimum distance of 15 cm
from walls and objects.
9. For safe setup e.g. on walls or
ceilings please use a safety cord.
The safety cord should be able to
withstand tenfold the weight of
the device. Please follow the accident prevention regulations of
professional associations and/or
comparable regulations for accident prevention.
10. If the device has been exposed to
great temperature changes, do
not switch it on immediately. Condensation (or any moisture/water
formed) may damage device.
11. Never use dimmer, RC or other
electronically switched sockets.
Whenever possible, do not use
the laser projector together with
large appliances (especially fog
machines) on the same mains!
12. Ensure sucient ventilation and
do not place the device on any
warm or heat radiating surface.
Especially the ventilation ope-
nings must not be covered!
13. Ensure that device does not get
overheated. Make sure that the
device is not exposed to spotlights (especially moving heads).
Heat of spotlights could overheat
laser in a little while and leads to a
degradation of performance.
14. This unit is intended for indoor
use only.
4. Working on the device
1. This product has no user serviceable parts inside and should only be maintained and serviced by a qualied engineer.
2. Be sure that the mains plug is not connected to the power
supply while installing.
3. Take o all reecting things like rings, watches etc. before
starting to work with or at the projector.
4. Only use non-reecting tools to work on device.
5. Wear protective clothing (like goggles, gloves etc.) according to laser power and wavelength of the laser.
page 4 / 12 EN
Manual: Club Series
5. Service notes
Moisture and heat can reduce lifetime of the laser system dramatically and expires
any warranty claim.
• Quick on/o switching of this device will reduce durability of the
laser diode dramatically.
• Avoid sharp knocks and shocks to
this device and ensure sucient
protection during transportation.
Look after your Laserworld product.
• To increase durability of your laser,
protect device against overheating:
• Always ensure sucient ventilation.
• Do not face spotlights (especially
moving heads) to the device.
• Check temperature after approx.
30 minutes with each new
installation. If necessary install the
projector at a place with dierent
temperature.
• Keep the device dry. Protect it
from moisture, rain and damp.
• Switch o device when it is not
needed. Diodes are switched on
and can wear out even if there is
no visible laser output.
• Please ensure the fans and heatsinks are clear from dust and
debris otherwise the risk of overheating may occur. If the unit and
airways appear to be blocked then
please contact a qualied service
engineer to maintain and service
the product.
• The devices of Ecoline, Evolution,
Club and Proline Series are not
meant for professional applications. After approx. one hour of
operation, the device should cool
down for about 15 minutes.
• Removal of the warranty label
as well as damages to the device
caused by improper handling,
neglect of the safety instructions and service notes will void
the warranty.
EN page 5 / 12
Manual: Club Series
6. Warnings and other notices on the device
Model type
Production
year
Wavelength
Output power
Power supply &
consumption
Please read manual before operation
Laser radiation!
Avoid exposure
to beam.
Use in enclosed spaces only!
Caution of
radiation
if cover is
Laser class 4
removed
page 6 / 12 EN
7. Device connections
CS-1000RGB
Laser Aperture
Beam block
Microphone
Microphone LED
Emission LED
fan
key switch
Manual: Club Series
DMX address
DMX in
DMX out
ILDA in
ILDA out
trim pot for
pattern size
EN page 7 / 12
ON / OFF
switch
Scan Fail
Safety switch
trim pot for
sensitivity
control
Interlock
connection
for power supply
Manual: Club Series
CS-2000RGB
Laser Aperture
Beam block
Microphone
Microphone LED
Emission LED
DMX in
DMX out
ILDA in
ILDA out
key switch
trim pot for
pattern size
fan
connection
for power supply
trim pot for
sensitivity
control
Interlock
DMX address
ON / OFF
switch
page 8 / 12 EN
Manual: Club Series
8. Operation
1. Connect the power cable to the device and then to the mains
2. Insert key and turn it ‚ON‘
3. Press „ON“ to switch the device on
4. The Interlock adapter is already attached. There is no need to change
anything. The show laser doesn‘t work if the Interlock adapter isn‘t connected to the device.
5. Safety Presets
This device has an integrated Scan Fail Safety (SFS). Is the Scan Fail Safety
active (on), single beams are prevented. If the Scan Fail Safety is switched
o always ensure that maximum permissible exposure (MPE) is not
exceeded in areas accessible to the public or members of sta.
6. Modes:
Your device runs in auto mode (random playback of the preset patterns):
Your device runs in music mode (random playback of the preset patterns
according to music, sound or any other noises):
Control the music sensitivity by the trim pot at the rear side of the device.
The Microphone LED (at the front side of the device) is ashing when the
device is triggered.
Your device runs in DMX mode if ‘10‘ is switched o:
EN page 9 / 12
Manual: Club Series
The DMX mode only works when a DMX controller is connected to the
laser.
Use the switches 1 - 9 to set the DMX address of the laser. Each switch
represents a number. To dene a number use the preceding number
and multiply it by 2:
Switch 1 2 3 4 5 6 7 8 9 10
Number 1 2 4 8 16 32 64 128 256 Mode Switch
The laser uses 11 DMX channels, so make sure that the next device uses
an address that doesn’t overlap with this range.
Channel Value Function
1 0 - 255 Mode selection
2 0 - 255 Pattern selection
3 0 - 255 Circular Movement
4 0 - 255 Y Rotation
5 0 - 255 X Rotation
6 0 - 255 Horizontal movement
7 0 - 255 Vertical movement
8 0 - 255 Manual Zoom
9 0 - 255 Pattern Buildup
10 0 - 255 Dot Eect with Strobe
11 0 - 255 Color Seletion
Please note that not each pattern can be combined with each eect!
page 10 / 12 EN
Manual: Club Series
ILDA control: Connect your device („ILDA IN“) via an ILDA cable to an interface
/ controller. Use a laser control software, to run the device. Use „ILDA OUT“
to connect it to another device. In ILDA mode all DIP switches should be
switched o.
Master-Slave-Mode: To use the daisy chain / Master-Slave-Mode connect two
(or more) laser projectors of the same series via DMX cables:
Master projector (DMX out) -> DMX cable -> slave projector 1 (DMX in) ;
slave projector 1 (DMX out) -> DMX cable -> slave projector 2 ...etc.
Master projector
Choose stand-alone or
sound-to-lightmode at
the master projector
(see above)
6. To turn o the device switch it o („OFF“), switch the key to „OFF“ and disconnect the power cable from the mains.
7. Close the beam block shutter to prevent laser output: Loose both screws
and slide the shutter in front of the window. Tighten the screws again. Do it
conversely to open the beam block shutter.
DMX cable
Slave projector
DMX setting at the slave
projector:
EN page 11 / 12
Loading...