Laser Pegs Zippy 004 Assembly Instruction Manual

Environmental Phenomena

* The unit may malfunction if subjected to radio-frequency interference. It SHOULD revert to
normal operation when the interference stops. If not, it may become necessary to turn the power
o and back on, or remove and reinstall the batteries.

* In the unlikely event of an electrostatic discharge, the unit may malfunction and lose memory,
requiring the user to reset the devise by removing and reinstalling the batteries.

Please read this manual before you begin!
Failure to follow this manual’s instructions may
result in damage to the Zippy Do® Power Base
and/or the Zippy Do® pieces. Not adhering to
these instructions will void the manufacturer’s
warranty. The packaging must be kept because
it contains important information.

This manual is copyright and cannot be reproduced or used online without Laser

Pegs®Ventures LLC permission. Copyright 2014 © All Rights Reserved US Patent

#7,731,558 Additional Global & Multiple Patents Pending. Laser Pegs®Ventures

LLC. 8304 Consumer Ct Sarasota FL. 34240. Contact: [e-mail]

Compatible with other construction kits

www.LaserPegs.com

WARNING:

CHOKING HAZARD-Small parts.

Not for children under 3 yrs.
Do not submerge in water.

Construction Compatible

EN71, RoHS COMPLIANT

This product complies to

all safety requirements

of ASTM F 963

Zippy Do® Parts List

by

To construct with Laser Pegs®, slide two pieces together to form
a connection. Slide each piece on and o smoothly. (Laser Pegs®
pieces sold separately).

Connecting Pegs

*To avoid short-circuits, keep metal objects and other
unauthorized materials from obstructing the peg holes.

Remove the Phillips head
screw with a 4mm screw

driver.

Requires

3-LR44 Button Cell

Batteries

Screw

Battery Compar tment
Cover

Batteries

Power Switch

Battery

Compartment

1. Remove the Phillips head screw.

2. Remove the Battery Compartment Cover.

3. Place three (3) LR44 batteries in the correct
position. (Batteries are to be inserted with the correct
polarity).

4. Replace the Battery Compartment Cover.

5. Replace the Phillips head screw.

6. Slide Power Switch to turn on!

7. Do not mix old and new batteries.

8. Do not mix alkaline, standard (carbon­ zinc), or rechargeable (nickel-cadmium, NiMH) batteries!

9. Exhausted batteries are to be removed
from the power base.

10. Batteries should be recycled or disposed of as per
state and local guidelines.

11. Non-rechargeable batteries are not to be recharged.

12. Rechargeable batteries are only to be recharged under
adult supervision.

13. Rechargeable batteries are to be removed from the
toy before being recharged.

14. The supply terminals are not to be short-circuited.

15. Do NOT throw batteries into re!

Replacing Batteries

x1

x1

x1

For Boys And Girls

Ages 3 And Up

LIGHTED

CONSTRUCTION SET INCLUDES:

• 21 Construction Parts

• Zippy Do® Power Base

• Instruction Manual

Requires 3-LR44 Batteries

Batteries

Included

12 Models+

004

ANY CREATION YOU CAN BUILD

x3

x1

underside of Zippy Do® Power Base

Power Switch

Slide Power Switch to turn on/o/ash

Slide Power Switch to cycle through dierent light settings.

®

This Product contains a button battery. If swallowed, it could

cause severe injury or death in just 2 hours.

Seek medical attention immediately.

The toy is not to be connected to more than
the recommended number of power supplies

x1

x2

x1

x1

x2

x1

x2

x1

x4

WARNING: STROBE LIGHTS
MAY CAUSE SEIZURES

Connects to other
Laser Pegs® pieces

BATTERIES ARE TO BE INSERTED
INTO THE TOY BY AN ADULT ONLY!

ONLY ADULTS SHOULD INSTALL THE BATTERIES

CAR

PLANE

HELICOPTER

SKI PLANE

Copyright 2014© All Rights Reserved Global & Multiple Patents Pending. US Patent #7,731,558

www.LaserPegs.com

DO NOT SUBMERGE IN WATER

Laser Pegs® CARES

Questions? Comments?

For additional compliance info:

1-866-432-3735

Contact: [e-mail]

X-1 SPACE GLIDERGYROCOPTER CAR

ZD1 ROCKET

EZ-E PLANE

ARMORED FIGHTING VEHICLE GYROCOPTER

ROADSTERSTUNT PLANE

MADE IN CHINA

FCC Notice:

Th

is device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired operation.

CAN ICES-3 (B) / NMB-3 (B)

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in

a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. H

owever,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encour

aged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.

 Consult the dealer or an experienced radio/TV technician for help.

Copyright 2014© All Rights Reserved Global & Multiple Patents Pending. US Patent #7,731,558

www.LaserPegs.com

Model

Diculty
Level

Model

Diculty
Level

CAR

PLANE

1

STEP

1

STEP

2

STEP

2

STEP

3

STEP

3

STEP

4

STEP

4

STEP

5

STEP

6

STEP

CAR: 1886 is regarded the year of birth for the modern automobile. Motorized wagons soon replaced animal­drafted carriages, especially after automobiles became aordable for many people when the Ford Model T was
introduced in 1908.

PLANE: Airplanes come in a variety of sizes, shapes, and wing congurations. The rst pow­ered airplane was own by the Wright brothers on December 17, 1903; over 100 years ago!