LaserLyte UTA-HAB User Manual

Auto-Off Feature:

• After 5 minutes in any mode, warning mode pulse will activate.

• After 1 minute in warning pulse mode, laser will turn off.

• Press the switch during warning pulse for laser reset.

YTE

ASER

L

L

YTE

ASER

L

L

YTE

ASER

L

L

5 min.

Batteries: 3 x 392 batteries

• Batteries can be changed with laser installed on gun!

• Remove battery cover

• Insert 3 x 392 batteries (+ side up).

• Tighten down the battery cover, and check periodically.

YTE

ASER

L

L

WARRANTY:

Three Year Limited

Warranty.

DANGER

LASER LIGHT AVOID DIRECT EYE EXPOSURE

POWER OUTPUT < 5mw WAVELENGTH 630-670mm

CLASS IIIa PRODUCT

YTE

ASER

L

L

30 N. Alamos Drive - Cottonwood, AZ 86326

Phone [phone] - Fax [phone]

www.LaserLyte.com

5 min.
6 min.

Off

®

REV414

UTA-HAB

®

• Fits : 9MM, 380 ACP, 40 S&W, 45 ACP

• Ergonomic activation

• Dual Modes: pulse and constant on

• Auto-Off feature

• Quick and Easy Installation

®

HI-POINT® 9mm, 380 ACP, 40 S&W & 45 ACP

L

ASER

L

YTE

UTA-HAB

YTE

L

ASER

L

YTE

L

ASER

L

YTE

L

ASER

L

YTE

L

ASER

L

* Read instructions completely before installing your laser.
Failure to do so may result in damage to your laser or firearm.

Installation:

•

UNLOAD FIREARM.

•

Attach danger label to side of gun near laser with arrow pointing

toward front sight

1

Place small button provided into button hole in left-side of laser body shell.

2

Place left-side of laser body shell on gun, ensuring proper button placement.

3

Move pre-assembled right-side laser body shell on top of trigger guard and
left-side and gently squeeze both sides together.
ENSURE PROPER BUTTON PLACEMENT.

4

5

From left side (non-battery cover side), insert three 1/2” hex head screws using

the larger .050 hex key provided. Tighten screws until snug.

Installation: •

1

4

UNLOAD FIREARM

2

L

YTE

L

ASER

3

L

ASER

L

YTE

5

Mounting on other gun: • UNLOAD FIREARM

1

Uninstall laser from gun.

2

Unscrew the Phillips Head Screw and remove Master Module.

3

Put long button in button hole. Put Master Module in place. Put Phillips
Head Screw back in place. Re-attach laser to gun.

2 3

J1

S1

U1

C1

Remove

Phillips Head

Screw

Activation:

1

Press once turns laser on: constant or pulse

2

Press and hold for 5 seconds to change mode.
Second press turns laser off.

3

1 2 3

This laser has ambidextrous activation.

ON/OFF

YTE

L

ASER

L

5 sec.

ON/OFF

L

ASER

L

or

YTE

ON/OFF

L

ASER

L

ON/OFF

L

ASER

L

YTE

or

YTE

Laser Sight In:

1

Use the provided .035 hex key to adjust the sight.

2

Always end adjustments on a clockwise turn.

3

Make final adjustments at shooting range.

1 3

2

ASER

L

Windage

Screw

YTE

L

Windage

right

left

YTE

ASER

L

L

Elevation

down

up

ON/OFF

Moving

Laser

Dot

YTE

L

ASER

L