LaserLyte LT-TTP, LT-TTPC User Manual
®
Reaction Tyme
®
Reaction Tyme
***With the LT-TTC, remove the "Plug" from the LT-PRO***
TRIGGER TYME™ PISTOL
LT-T TP & LT-TTPC
• This gun cannot be fired. Please respect all gun rules
and always point this in a safe direction.
For use with the LaserLyte® LT-PRO Universal Laser Trainer
•
Instructions for use:
1
Make the LT-PRO ready and insert into the barrel of the
Trigger Tyme™ Pistol.
2
Pull the trigger to to activate the laser.
is tight in the barrel.
Aim in a safe direction and shoot the laser at desired
3
Ensure the LT-PRO
targets.
Works great with LaserLyte targets.
- Laser Target, TLB-1: 62 LEDs light up on target, showing the shots
- Reaction Tyme, TLB-RT:
1
2 training modes, active reaction training
REV 0214
2
3
Pistol Laser Trainer
Installation:
THE BATTERIES ARE ALREADY INSTALLED,
YOU MUST REMOVE A PIECE OF PLASTIC
INSULATOR BEFORE OPERATION
UNLOAD YOUR FIREARM!
Remove plastic insulator from batteries.
Insert screw through adapter and thread
into taper of trainer.
Tighten or loosen screw for caliber fit.
Gently press the trainer into the muzzle of
the pistol.
Ready your pistol and pull trigger to fire
red laser dot. (LaserLyte recommends
the use of snap caps.)
When removing from your pistol, pull
straight out! Do not twist! Ensure all parts
are out of barrel
When not in use remove batteries and
insert insulator for storage.
1
2
Batteries: (3) 377
Unscrew Battery cap.
Remove batteries.
Install new batteries.
Tighten battery cap.
1
2
3
4
3
4
6
7
8
5
LT-PRO
Training with
the LT-PRO
will improve:
• Trigger Control
• Unsighted Fire /
Point and Shoot
• Shooting from the
Holster
• Precision Shooting
• Unorthodox Shooting
Positions
STOP
+ + +
insulator
Pistol Laser Trainer
Installation:
THE BATTERIES ARE ALREADY INSTALLED,
YOU MUST REMOVE A PIECE OF PLASTIC
INSULATOR BEFORE OPERATION
UNLOAD YOUR FIREARM!
Remove plastic insulator from batteries.
Insert screw through adapter and thread
into taper of trainer.
Tighten or loosen screw for caliber fit.
Gently press the trainer into the muzzle of
the pistol.
Ready your pistol and pull trigger to fire
red laser dot. (LaserLyte recommends
the use of snap caps.)
When removing from your pistol, pull
straight out! Do not twist! Ensure all parts
are out of barrel
When not in use remove batteries and
insert insulator for storage.
1
2
Batteries: (3) 377
Unscrew Battery cap.
Remove batteries.
Install new batteries.
Tighten battery cap.
1
2
3
4
3
2
3
4
4
6
7
8
5
DANGER
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
POWER OUTPUT < 5mw
WAVELENGTH 630-670mm
CLASS IIIa PRODUCT
®
A Division of P&L Industries
101 Airpark Road - Cottonwood, AZ 86326
Phone 928-649-3201 - Fax 928-649-3970
www.LaserLyte.com
LT-PRO
WARRANTY:
One Year Limited
Warranty.
Training with
the LT-PRO
will improve:
• Trigger Control
• Unsighted Fire /
Point and Shoot
• Shooting from the
Holster
• Precision Shooting
• Unorthodox Shooting
Positions
STOP
+ + +
insulator
Batteries: (3) 377
Batteries: (3) 377
Batteries: (3) 377
Unscrew Battery cap.
Remove batteries.
Install new batteries.
Tighten battery cap.
1
2
3
4
When not in use:
Unscrew adapter.
Insert into LT-PRO as shown.
7
8
Laser Trainer Pro
LT-PRO
LT-PRO Adapter Plug Screw Hex Key
Laser Trainer Pro
LT-PRO Adapter Plug Screw Hex Key
THE SOUND ACTIVATED SWITCH IS ALWAYS LISTENING
•
THE BATTERIES ARE ALREADY INSTALLED. YOU MUST REMOVE THE
•
PLASTIC INSULATOR BEFORE OPERATION. SEE BATTERIES SECTION
FOR INSTRUCTIONS.
Installation:
UNLOAD YOUR FIREARM!
1
2
Insert screw through plug & adapter and thread into taper of trainer as shown above.
Tighten or loosen screw for caliber fit.
3
4
Gently press the trainer into the muzzle of the pistol.
Ready your pistol and pull trigger to fire red laser dot.
5
(LaserLyte recommends the use of snap caps.)
When removing from your pistol, pull straight out!
6
Do not twist! Ensure all parts are out of barrel.
When not in use:
Unscrew adapter.
7
8
Insert into LT-PRO as shown.
2
3
4
***With the LT-TTC, remove the "Plug" from the LT-PRO***
+ + +
insulator
5
6
Correct removal
7
8
LT-PRO
NO
NO
1
Unscrew Battery cap.
2
Remove batteries.
3
Install new batteries.
4
Tighten battery cap.
Loading...