LaserLyte CK-MS User Manual
Auto-Off Feature:
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
• After 5 minutes in any mode, warning mode pulse will activate.
• After 1 minute in warning pulse mode, laser will turn off.
• Press the switch during warning pulse for laser reset.
5 min.
Batteries: 2 A-76 batteries
• Batteries can be changed with laser installed on gun!
• Use .050 hex key to remove battery cover.
• Insert 2 A-76 batteries (+ side up).
• Note: Dimple on battery cover must be face down.
• Tighten down the battery cover, and check periodically.
5 min.
6 min.
Off
CK-MS
®
• Fits Bersa Thunder .380 & .380 Plus
• Quick and Easy installation
• Works with nylon holsters
- Blackhawk® #7
- Uncle Mike’s® #15
• Ergonomic activation
• Dual laser modes with auto-o feature
WARRANTY:
One Year Limited
Warranty.
DANGER
LASER LIGHT AVOID DIRECT EYE EXPOSURE
POWER OUTPUT < 5mw WAVELENGTH 630-670mm
CLASS IIIa PRODUCT
Dimple
Down
30 N. Alamos Drive - Cottonwood, AZ 86326
Phone 928-649-3201 - Fax 928-649-3970
www.LaserLyte.com
®
REV312
®
L
ASER
L
YTE
BERSA
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
L
ASER
L
YTE
BERSA
Trigger Guard Laser for the Bersa Thunder .380 & .380 Plus
L
ASERLYTE
L
BERSA
ASERLYTE
* Read instructions completely before installing your laser.
CK-MS
Failure to do so may result in damage to your laser or firearm.
Installation:
•
•
UNLOAD FIREARM.
Attach danger label to side of gun near laser with arrow pointing
toward front sight.
•
DO NOT TOUCH THESE SCREWS. (Figure A)
1
Place each side of CK-MS laser on front of trigger guard
(battery cover on right).
2
Insert four attachment screws from left side as shown. Tighten
down until snug with the .050 hex key provided.
tighten down battery cover. Do not over tighten battery cover, and
check periodically.
3
When properly installed, the Disassembly Lever will glide easily
With same hex key,
past the laser.
•
UNLOAD FIREARM.
•
Attach danger label to side of gun near laser with arrow pointing
toward front sight.
•
DO NOT TOUCH THESE SCREWS.
(Figure A)
1
LEFT
SIDE
L
ASERLYTE
RIGHT
SIDE
BERSA
2
3
Activation:
1
Press once turns laser on: constant or pulse.
2
Press and hold for 5 seconds to change mode.
Second press turns laser off.
3
1 2 3
CK-MS laser has ambidextrous activation.
ON/OFF
5 sec.
ON/OFF
or
ON/OFF
ON/OFF
or
Laser Sight In:
1
Use the provided .035 hex key to adjust the sight.
2
Always end adjustments on a clockwise turn.
3
Make final adjustments at shooting range.
1 3
2
Windage
right
left
Elevation
up
down
ON/OFF
Moving
Laser
Dot
Loading...