LaserLiner Greenline-Laser 1 Pro Operating Instructions Manual

Greenline-Laser 1 Pro

GB

D

NL

F

DK

E

Bedienungsanleitung
Operating instructions
Gebruiksaanwijzing
Betjeningsvejledning
Mode d´emploi
Instrucciones para su uso
Istruzioni d'uso

Instrukcja Obsługi

Käyttöohje
Instruções de uso

I

PL

FIN

P

3-8

9-14
15-20
21-26
27-32
33-38
39-44
45-50
51-56
57-62

036.00.00A / Rev 09.06

Greenline-Laser 1 Pro

ENGLISH 9

Green line laser for all floor and wall work.

Greenline-Laser, 522-542 nm, for ground applications as well as for
horizontal and vertical levelling directly on the wall. The length and intensity
of the laser line can be adjusted. The laser is fixed to the wall using special
pins and precisely aligned through the eccentric adjustment. Parallel shifts
can be performed through the exact alignment of the laser line to the body
edges. Additional magnets on the underside also allow the device to be
mounted on steel structures. Precision: 3 mm / 10 m.
Incl.: High-performance rechargeable battery, mains unit / battery charger,
laser enhancement glasses and carrying case.

General safety instructions
Caution:

Do not look directly into the beam. Lasers must be kept out of

reach of children. Never intentionally aim the device
at people. This is a quality laser measuring device
and is 100% factory adjusted within the stated

tolerance. For reasons of product liability, we must
also draw your attention to the following: Regularly check the calibration
before use, after transport and after extended periods of storage. We also
wish to point out that absolute calibration is only possible in a specialist
workshop. Calibration by yourself is only approximate and the accuracy of
the calibration will depend on the care with which you proceed.



Note:

This product is a precision instrument that must be handled and
treated with care. Avoid shocks and impact. Always keep and carry in the
case! For cleaning, use a soft cloth and glass cleaner.

LASER LIGHT

DO NOT LOOK INTO

THE BEAM!

CLASS 2 M LASER

EN 60825-1:2003-10

Warranty:

The warranty period is 2 years from the date of purchase. The warranty
covers all material or manufacturing defects occurring during this time. The
following are excluded from warranty: Damage due to improper use (e.g.
operation with wrong type of current/voltage, connection to unsuitable
power source, fall onto hard surface, etc.) or improper storage, normal wear
and tear, and defects which only insignificantly impair the value or suitability
for use. Any tampering by unauthorised persons will render this warranty
void. In the event that you need to claim warranty, please take the complete
device together with all information and the invoice to one of our dealers or
send it in to Umarex-Laserliner.

Greenline-Laser 1 Pro

ENGLISH10

1

2345

6

10

8

7

9

11



Note: The horizontal and vertical spirit levels are intended solely for
applications on walls. The spirit levels are not suitable for floor applications
because they are not adjusted to the bearing area. Therefore the device
cannot be used as a water level.

1 Laser exit window

2 Horizontal spirit level for

applications on walls

3 Vertical spirit level for

applications on walls

4 Battery compartment

5 Eccentric adjustment

6 On/off switch

7 Operating display

8 Adjustment wheel for

adjusting the intensity
distribution and length
of the laser line

9 Magnets

10 Fastening pins

11 Mains adapter/charger

connecting socket

Charging the accu

• Before using the Greenline-Laser 1 Pro,

fully charge the accu.

• Open the battery compartment (4),

insert the accu and connect the plug
to the socket. The plug fits in the
socket in one position only. Reclose the
battery compartment.

• Connect the battery charger / mains

unit to a mains source and plug into
the socket (11). Please only use the
charger/mains unit supplied with the
device. If a different one is used, the warranty will become void.

• The device can also be operated with standard alkali batteries (4 x type

AA). Insert the batteries as shown by the installation symbols. Ensure the
polarity is correct.

• If the LED (7) blinks constantly, either the batteries must be exchanged or

the accu recharged.

Greenline-Laser 1 Pro

ENGLISH 11



Note: Do not expose batteries to excessive heat such as sunshine, fire, etc. Dry
batteries must not be recharged. Used batteries must not be disposed of as
household waste. Please take them to a collection point for used batteries or for
special waste. Ask your local authority for further details. Batteries with the
recycling symbol can also be returned to our dealerships or to our Technical
Service.

Green laser technology

Unlike red lasers, green laser light can only be indirectly generated. Because
of the system, therefore, fluctuations may occur:

• Different levels of line brightness between one device and another.

• The optimum operating temperature is 20°C. Outside of the working

temperature range of 0-40°C, green lasers become darker.
TIP: Before switching on the device, wait until it has had time to adjust to
the ambient temperature.

These fluctuations are excluded from claims.

Greenline-Laser 1 Pro

ENGLISH12

Due to the physiology of the human eye green appears brighter to us than
red. Therefore green lasers are highly visible compared to customary red
lasers. They enable applications on dark surfaces, longer distances and
performance of work in very bright ambient light.

Floor applications

• Put the device on the floor and switch it on using

the on/off switch (6).

• A green laser line is projected. The intensity

distribution and length of the laser line can be
adjusted using the adjustment wheel (8). Thus
maximum visibility of the laser line is guaranteed,
particularly on dark floors, in very bright ambient
light or on uneven surfaces.

• The spirit levels (2,3) do not have any function in this application area, see

also the note on page 10.

• 45° and 90° angles can be installed with the optional installation plate (Art.

no.: 036.01), see next page.

Wall applications

• First fix one of the two fastening pins (10) in the

desired position on a drywall.

• Then attach the device with the fastening hole at

the front to the pin, pre-adjust it horizontally and/or
vertically with the spirit levels (2,3) and fix it on the
wall with the second pin.

• Align the device exactly horizontally and/or

vertically with the eccentric adjustment and the
fastening pins. Adjust the intensity distribution if
required (Adjustment wheel 8).

• IMPORTANT: For horizontal levelling always carry out alignment with the

upper spirit level!

Parallel projection

The body edges can be used to carry out parallel
translations and depict 90° angles.

Greenline-Laser 1 Pro

ENGLISH 13

Technical data

Precision + 3 mm / 10 m
Working range (depending on ambient brightness) ca. 30 m
Laser wavelength

522 – 542 nm

Line laser / Laser output rating Classe 2 M / < 5 mW

Rechargeable battery operating time /
Recharging time

ca. 8 h /
ca. 16 h

Battery operating time

ca. 16 h / 4 x Typ AA
Weight 0,5 kg
Operating temperature 0°C ... + 40°C
Storage temperature -10°C ... + 70°C
Order number 036.00.00 A
Subject to technical alterations 09/2006



Note:

Regularly check the calibration before use, after transport and after
extended periods of storage.

Working with accessories

Floor tiles can be installed exactly and
efficiently with the optional
installation plate (Art. no. 036.01).
Now the device can easily project 45°
and 90° alignments. Work can be
performed with one as well as several
devices.

Greenline-Laser 1 Pro

ENGLISH

14



Note:

If points A1 and A5 are more than 3 mm / 10 m, the device is in need of
calibration. Contact your authorised dealer or else the UMAREX­LASERLINER Service Department.

Checking horizontal calibration:

1. Mark point A1 on the wall. Attach the device in the centre of point A1,

align it, and switch it on. Adjust the laser line so that it reaches the end of
the wall, see page 12.

2. Mark point A2 and continue until point A5 is marked. Divide the distance
between A1 and A5 by the overall length (S1 + S2 + S3 + S4). The device
is within the tolerance if the difference between A1 and A5 is not greater
than 3 mm / 10 m.

A1

A2

A3

A4

A5

Checking vertical calibration:

Fix a plumb bob with a line at least 2.5 m in length on the wall, making sure
that the bob can swing freely. Attach the device at the end of the plumb line
in the centre, align it vertically and switch it on. The precision is within the
tolerance if the deviation between the laser line and plumb line is not greater
than 3 mm / 10 m.

S1

S2

S3

S4

GmbH & Co KG
Donnerfeld 2
59757 Arnsberg, Germany
Tel.: [phone], Fax: -333
www.laserliner.com

Dirección de envío y de servicio
post-venta:

Telefon: [phone]
Fax [phone]

Indirizzo servizio manutenzione

- Indirizzo di spedizione

Telefono [phone]
Fax [phone]

Adres serwisu i wysyłki:

Telefon Serwisu+49 2932 638-300
Fax [phone]

Huolto- ja lähetysosoite:

Puhelin [phone]
Fax [phone]

Endereço de serviço e envio:

Telefone [phone]
Fax [phone]

Service- und Versand-Anschrift:

Service-Telefon [phone]
Fax [phone]

Service- and Shipping Address:

Service phone [phone]
Fax [phone]

Service- en verzendadres:

Servicetelefoon [phone]
Fax [phone]

Service- og Postadresse

Service-Telefon [phone]
Fax [phone]

Livraison et expédition:

Telefon: [phone]
Fax [phone]

Umarex GmbH & Co KG
– Laserliner –
Möhnestraße 149, 59755 Arnsberg, Germany
[e-mail]

GB

D

NL

I

E

PL

DK

FIN

F

P

Greenline-Laser 1 Pro

LASERSTRAHLUNG

NICHT IN DEN

STRAHL BLICKEN!

LASER KLASSE 2 M

EN 60825-1:2003-10