Page 1
DigiLevel Pro 30/60/120
DE
GB
NL
DK
FR
ES
IT
PL
FI
PT
SE
NO
TR
RU
04
08
12
16
20
24
28
32
1250
Laser
650 nm
300
610
UA
CZ
EE
LV
LT
RO
BG
GR
Page 2
DigiLevel Pro 30/60/120
Pointlaser
ON / OFF
Pointlaser
650 nm
30 mm
02 03
Page 3
Digital electronic spirit level with vertical and horizontal angle display and
point laser (650 nm).The slope can be indicated in degrees, IN/FT or percent
on the display.An acoustic signal indicates the horizontal or vertical position.
The slope memory enables angles to be projected elsewhere, while
the separate measurement memory allows up to 9 measurements results
to be stored and retrieved. Milled measuring surfaces, powerful fi xing
magnets, as well as additional vertical and horizontal vial, illuminated display.
Calibration function for increased accuracy and adaptation to measuring
surface.
97108
1
2
3
4
5
6
DigiLevel Pro 30/60/120
Inserting batteries:
Open the battery compartment (17) on the rear of the DigiLevel and
insert two new batteries (type AAA/LR03) in the manner indicated
by the installation symbols. Ensure correct polarity. The symbol (10)
indicates the level of battery charge.
Switching on and measuring:
The DigiLevel Pro can measure angles continuously to 360°.
• Switch the DigiLevel Pro on using the on/off switch (2).
• The current operating temperature in °C is shown for a few seconds.
• The slope angle is shown in the display (8). If slopes are measured
overhead, the direction of display adjusts automatically.
• The current slope direction is also shown by the symbol (7).
15
Keypad
1. (REF) – Angle reference value setting
2. ( ) – ON / OFF switch
)
)
) ) – Acoustic signal on/off
11
17
16
3. (
4. (MR) – Memory retrieval
5. (UNIT) – Unit of measurement selection
(° degrees / % / IN/FT)
6. (M) – MEMORY function
Display
13
7. Slope direction
8. Slope angle
9. Current memory position (M1 – M9)
10. Battery charge
DigiLevel Pro 30/60/120
11. Vertical vial
12. Horizontal vial
13. Magnets
14. Measuring surface, 30 / 60 / 120 cm
15. Point laser ON / OFF
12
GB
08
16. Tripod threads, 1/4"
14
Rear
17 . Battery compartment
Selection of unit of measurement:
• Button (5) allows the desired unit of measurement to be selected
(° degrees, %, IN/FT)
Changing the angle reference value:
• With button (1), it is possible to transfer angles elsewhere. To do so,
set the device to the desired slope and press button (1). The display will
then change to “0.0”, and the desired reference angle is now set.
The slope can now be transferred to other objects.
IMPORTANT: When all the slopes have been transferred, make sure
to deactivate the new angle reference value. To do this, switch off
the device by pressing the on/off switch (2) for at least 3 secs. Only
then will the value be reset itself to the measuring surface (14).
Acoustic signal:
• The acoustic signal can be switched on or off with button (3).
• When the angle of slope stands at 0°, 45°, 90° or the most recently
stored value, this is indicated by an acoustic signal.
NOTE: When working with a changed angle reference value, the
acoustic signal is activated on reaching the new reference value
(0°, 45°, 90° display).
GB
09
Page 4
Spirit level function:
• The alignment to the measuring surface (14) is shown by the vertical and
horizontal vials (11, 12).
• Use the vials for optimum vertical and horizontal alignment, and the
electronic slope angle display for any desired angle of slope.
• With the aid of the magnets (13), the DigiLevel Pro can be affi xed to any
magnetic surface.
Memory functions:
• With the memory function (6), the current measurement result can be
saved in the internal memory, whereby the current memory position
(M1 - M9) is displayed during the saving process (9).
• If more than 9 results are saved, the old ones are overwritten.
• The memory retrieval button (4) can be pressed to show the most
recently saved result in the display (8). By repeatingly pressing the
memory retrieval button (4), all the stored results (9) can be retrieved.
• Return to normal (6)
Calibration:
• (A) Place the unit with its measuring edge (14) down on a straight sur-
face and mark the positions of the unit‘s ends on the underlying surface
(see Fig. below). Switch the unit on (2) and press the REF button (1) until
CAL 1 starts blinking. Shortly thereafter an acoustic signal will sound and
CAL 2 will appear in the display. Now turn the unit around horizontally
(end-for-end) by 180° (B) such that its ends are positioned opposite where
they previously were but again exactly at the underlying surface marks
(reverse measurement). Again press the REF button (1) until CAL 2 blinks.
The subsequent acoustic signal concludes the process.
• Follow-up test: The unit is properly calibrated when it displays the same
measurement value, i.e. the underlying surface‘s deviation from absolute
level, in both positions (0° and 180°).
(A)
0°
DigiLevel Pro 30/60/120
Switching off:
• To switch off the DigiLevel, press the on/off switch (2) for at least
3 secs. When not in use, the DigiLevel switches off automatically.
Technical data:
Electronic measuring
precision:
Display accuracy 0°- 1° 2 decimal places
Display accuracy 1°-90° 1 decimal place
Vial accuracy
Laser class 2 < 1 mW (EN 60825-1:2007-10)
Laser wavelength 650 nm
Working temperature 0°C...40°C (32°F...104°F)
Storage temperature -20°C ... 65°C
Power supply 2 x 1.5V (Typ AAA/LR03)
Dimensions 30 60 x 33 x 300 mm
Dimensions 60 60 x 33 x 610 mm
Dimensions 120 60 x 33 x 1220 mm
Weight 30/ 60/ 120 0,4 / 0,8 / 1,2 kg
Article-No. 30/ 60/ 120 081.212A/ 081.210A/ 081.216A
Subject to technical change without notice 10.2008
Do not stare into the beam!
General safety instructions
Attention: Do not look directly into the laser beam! The laser may not
get into the hands of children! Do not point this device unnecessarily
toward persons.
Note: Regularly check the unit‘s calibration before use, after transporting
and extended periods of storage.
+/- 0,1° at 0° and 90°,
+/- 0,2° at 2° – 89°
+
0,5 mm/m
Laser radiation!
Class 2 laser
< 1 mW · 650 nm
EN 60825-1:2007-10
Warranty:
(B)
GB
10
180°
The warranty is valid for 2 years from the date of purchase. The warranty does
not cover damage caused by improper use or storage, normal wear and tear, or
defects which only insignifi cantly impair the value of the product or its
functioning. Any tampering by unauthorised persons will render this warranty
void. In the event that you need to claim warranty, please take the complete
device together with all information and the invoice to one of our dealers or send
it in to UMAREX-Laserliner.
GB
11
Page 5
DigiLevel Pro 30/60/120
DE
Service- und Versand-Anschrift
GB
Service- and Shipping Address
NL
Service- en verzendadres
DK
Service- og Postadresse
FR
Livraison et expédition
ES
Dirección de servicio y de envío
IT
Indirizzo di assistenza e di spedizione
PL
Serwis i sprzedaż
SERVICE
*
Umarex GmbH & Co KG
– Laserliner –
Möhnestraße 149, 59755 Arnsberg, Germany
Tel.: +49 2932 638-300, Fax: +49 2932 638-333
laserliner@umarex.com
Umarex GmbH & Co KG
Donnerfeld 2
59757 Arnsberg, Germany
Tel.: +49 2932 638-300, Fax: -333
www.laserliner.com
30: 081.212A / 60: 081.210A / 120: 081.216A /Rev.1008
Loading...