Larson Electronics HALP-48-2L-ITG-LED-1227 User Manual

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Class 1 Division 2 Hazardous Location LED Light - Corrosion Resistant for Marine (Saltwater)

Part #: HALP-48-2L-ITG-LED

Page: 1

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Made in Texas

The Larson Electronics HALP-48-2L-ITG-LED Hazardous Area LED Light Fixture is U.S./Canada U.L. approved Class 1 Division 2
Groups A, B, C and D, UL 1598A listed, and is specifically designed to handle the rigors of wet and corrosive marine environments.
This integrated hazardous location LED light has a T4 temperature rating and carries a United States Coast Guard approval, making it
ideal for applications such as oil rigs, ships, offshore applications, petrochemical, manufacturing, chemical storage, and water
treatment centers.

This four foot integrated LED fixture is ideal for operators seeking a top quality explosion proof LED light that will reduce operating costs, improve
lighting quality and reduce downtime incurred from frequent servicing intervals. The HALP-48-2L-ITG-LED fixture is equipped with a specially
designed integrated LED array which produces 19,200 lumens of bright light in a 160° wide flood beam spread, resulting in 50% more foot
candles of illumination at 8 feet as compared to standard T5HO lamps when measured with an Extech light meter. Our integrated series are
visibly brighter than standard T5HO's and have consistently surprised many of our customers with their unexpectedly high light output levels.

Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge

This Class 1 Division 2 rated fixture is constructed of non-corrosive materials including a polyester housing reinforced with glass fiber, a poured
in gasket for reliable sealing and an impact resistant acrylic diffuser. Eight corrosion resistant plastic latches secure the lamp cover to the housing
and provide a firm lock against the poured in seal to prevent drips and water intrusion.
The HALP-48-2L-ITG-LED is UL 844 rated and Class 1 Division II, Groups A, B, C, D approved. This fixture also carries a UL 1598A outdoor
marine rating and meets US Coast Guard specifications. This lamp offers the extreme durability, high efficiency and long lamp life of high power
LEDs in a proven hazardous location fixture design, making it a reliable and affordable lighting solution for open areas where flammable
chemicals and vapors may occasionally be present. Click here to read the NEC description for explosion proof and hazardous locations.
We have eliminated the ballast box normally associated with fluorescent fixtures which reduces overall weight and creates a slimmer unit profile.
There is no ballast in this unit and the integrated LED array has a 60,000+ hour service life, both of which result in extreme efficiency and greatly
reduced maintenance costs. The solid state design of LED technology give this fixture superior resistance to damage from vibration, extremes in
temperature, and a lamp life over twice that of standard fluorescent bulbs.

Page: 2

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Unlike the glass tube design of traditional fluorescent lamps, this integrated LED array has no filaments or fragile housings to break during
operation. Instead of using a combination of gases to produce light, light emitting diodes (LEDs) use semi-conductive materials that illuminate
when electric current applied and emitting light. With LED lights, there is no warm up time or cool down time before re-striking and provide instant
illumination when powered on, adding to the reliability of LED technology. By nature, LED light sources run significantly cooler than fluorescent
lamps, reducing the chance of accidental burns and increased temperatures due to heat emissions. This integrated LED array design of light
emitting diodes provides a more reliable, stable, durable, and energy efficient light source over traditional fluorescent lighting.
The LED array in this fixture produces 80% more illumination than standard T8 bulbs while offering lower amp draw and increased reliability. The
LED array produces 19,200 lumens at 120 lumens per watt. A HALP-48-3L-T5HO hazardous location fluorescent light, with a combined total of
162 watts, draws 1.35 amps at 120 volts AC and produces 15,000 lumens. This LED version of the same light, with a total of 160 watts, draws
only 1.3 amps at 120 volts AC and produces 19,200 lumens. The drivers in this unit provide the ability to automatically monitor and adjust input
current to maintain the correct LED voltage levels regardless of input levels across a specific range. The HALP-48-2L-ITG-LED is universal
voltage, not multi-tap, and operates on any voltage ranging from 90 to 305V AC or 127 to 431V DC without any modifications necessary. We also
offer other variations of this light if needed to fit your specific application, 347-480V AC, 12-24V DC, 48V DC, and 0-10V dimmable models upon
request.

Energy Consumption Comparison

T5HO T8 Integrated LED

Wattage 216 watts 112 watts 160 watts
Amp Draw @ 120V AC 1.8 amps 0.93 amps 1.33 amps
Amp Draw @ 220V AC 0.98 amps 0.51 amps 0.73 amps
Amp Draw @ 240V AC 0.9 amps 0.47 amps 0.23 amps
Amp Draw @ 277V AC 0.78 amps 0.40 amps 0.67 amps
Amp Draw @ 12V DC 18 amps 9.33 amps 13.33 amps
Amp Draw @ 24V DC 9 amps 4.67 amps 6.67 amps
Fixture Lumens 20,000 14,000 19,200
Lamp Life Expectancy 20,000 hours 24,000 hours 60,000 hours
Color Temperature 5000K / 4100K 4100K 6000K
Operation cost per year

(12hs/day @ 12c/kWh)

Please note: The above energy tables are comparing 4ft 4-lamp fixtures to the HAL-48-2L-ITG-LED-BMSW integrated LED fixture. The light
output is comparable to a 4ft 4-lamp fixture, but the form factor is of a 4ft 2-lamp fixture. This fixture has the same output as our HALS-48-4L with
four 54 watt T5HO lamps, but in the compact form factor of the HAL-48-2L-BMSW housing. Currently you cannot achieve comparable light output
in the same form factor from fluorescent lighting.

Mounting Options:

Unless otherwise specified, our standard, most popular configuration is the flange mount shown enlarged below. We also offer a pendant mount
for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit). Additional mounting configurations can
be customized to meet the requirements on the application. Please contact us for special mounting configurations.

$113.53 $58.87 $84.10

Page: 3

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Surface Mount (Standard)
Click Photo to Enlarge

Standard Flange Brackets:

Flange type stainless steel mounts attached at each end of the fixture enables it to be simply secured to any surface. The mounts provide some
shock absorbency protection while enabling the user to simply mount the fixture with the through-hole taps that protrude on each side of the
fixture. The mounting holes are 38.25” on center apart along the top of this hazardous location light. The mounting holes are 7.2” on center
across the top of the light.

Page: 4

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Pendant Mount (Optional)
Click Photo to Enlarge

Standard Suspension Mounting:

Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture is equipped with two 3/4” NPT hubs, one on each end
of the fixture. Operators bring rigid pipe down to the threaded mounting hubs. Wiring is fed down through the rigid pipe to one of the NPT hubs
and tied in to the fixture’s lead wires, completing the electrical connection. The remaining pendant hub provides support for the opposite end of
the fixture.
Suggested Applications: The HALP-48-2L-ITG-LED is designed for marine, wet, damp locations where corrosion resistant fluorescent lights
are required or are already present. This includes petrochemical facilities, lubrication pits, oil drilling rigs, crew quarters, solvent/cleaning areas,
water treatment areas, processing plants and marine loading docks.

Made in USA Quality Superior LED Benefits

Page: 5

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

1. 60,000 hour lifespan.

2. Can SAVE 50% or more on energy.

1. Each unit dialectically tested.

2. Fixture arrives assembled and lamped to reduce installation time and
cost. Flange type stainless steel mounts attached at each end of the
fixture enables it to be simply secured to any surface.

3. Fixture housing constructed of glass fiber reinforced polyester.

4. No ballast box. No ballast to replace. We simply run the black wire to
one end of the bulb and white wire to the other.

5. Re-lamping done via 6 stainless steel snap locking latches which
enables the operator to remove the door and access the lamps.

6. Lamp cover-diffuser constructed of high impact acrylic for corrosion
resistance and lamp protection.

7. 3/4 inch, threaded access hole for wiring conduit.

3. Qualifies retrofit projects for financial incentives, including utility
rebates, tax credits and energy loan programs.

4. Reduces energy use and prolongs life-spans of peripheral cooling
units (A/C, refrigeration)

5. 100% recyclable.

6. No toxins-lead, mercury.

7. No UV light, infrared radiation or CO2 emissions.

8. Qualifies buildings for LEED and other sustainable business
certifications.

9. Bright, even light maintains consistent color over time.

10. Instant on/off – No flickering, delays or buzzing.

11. Very good color rendering.

12. Vibration/impact resistant.

13. Significantly cooler operation.

14. Less frequent outages, higher output improves workplace safety.

Page: 6

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Specifications / Additional Information

HALP-48-2L-ITG-LED Hazardous Area LED Offshore Light U.L. Ratings
UL Listing: United States - Canada Class 1 Division 2, Groups A, B, C, D
Dimensions: W-8.25" x L-52" x H-7" UL 844
Weight: 13 Lbs UL 1598A Marine Type (Salt water)
Total Watts: 160 watts California Title 24 Compliant
Total Lumens: 19,200 T4A Temperature Rated
Voltage: Universal 90 to 305V AC or 127 to 431V DC Integrated LED Assembly
Lamp Life Expectancy: 60,000 Hours Made in the USA
Luminous Efficacy: 120 Lm/w
Temp Range: -30°C to +85°C
Beam Angle: 160°
Color Temp: 6000K
Minimum Operating Temp: -30° C
Maximum Case Temp: 90° C
Mounting: Flange Type Surface Mount or Pendant Mount
Materials: Polyester Housing Reinforced with Glass Fiber Special Orders- Requirements
Wiring Hub: 3/4 inch threaded Contact us for special requirements
Lens Material: Acrylic Lens Toll Free: 1-800-369-6671
Warranty: YES- 3 Years* Intl: 1-903-498-3363
U.L Approval: U.S Certificate Canada Certificate E-mail: [e-mail]

*3 year warranty replacement on this LED light (or LED bulbs for light
fixtures with removable LED bulbs). After 30 days, the customer ships
the failed LED light and/or LED bulb to Larson Electronics at their
expense. If the failure is a manufacturer defect, we will ship a new
replacement to the customer. If failure occurs within 30 days of receipt,
Larson Electronics will provide a return label via email to the customer.
When the failed light is returned, Larson Electronics will ship a new
replacement. Please click here to see our 3 Year Warranty pamphlet.

Scroll Down to Purchase

Part #: HALP-48-2L-ITG-LED (105692)

Page: 7

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Page: 8

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Links (Click on the below items to view):

- Dimensional Drawing

- STEP

- Hi-Res Image 1 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 2 - Class 1 Division 2 Hazardous Location Integrated LED Light

Page: 9

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

- Hi-Res Image 3 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 4 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 5 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 6 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 7 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 8 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 9 - Class 1 Division 2 Hazardous Location Integrated LED Light

- Hi-Res Image 10 - Class 1 Division 2 Hazardous Location Integrated LED Light

Page: 10