9419 E US HWY 175, Kemp, TX 75143 Phone: 903.498.3363 Fax: 903.498.3364 Email: sales@LarsonElectronics.com
33 Watt Low Voltage LED Fixture for Hazardous Location Lighting - Low Profile Linear Fixture - C1D2
Part #: HAL-48-33W-LED
Buy American Compliant
The Larson Electronics HAL-48-33W-LED is a low voltage hazardous location lighting solution approved for Class 1 Division 2
environments and UL 1598 listed for use in wet locations. This powerful 46.88" long LED strip light produces 2416 lumens, operates
from 12 or 24 VDC, and is suitable for a variety of applications.
The HAL-48-33W-LED is designed to provide a high output and ruggedly durable lighting solution for applications where Class1 Division 2
compliance is required. This low voltage explosion proof light can be operated with either 12 or 24 volt DC current and includes 6 feet of
connecting lead with standard two wire configuration. This light is constructed of powder coated extruded aluminum for excellent strength and
durability and is rated IP54 for protection against exposure to splashing water and limited dust ingress. These units are configured in a 46.88"
long strip or "bar" profile for installation in locations where wide dispersal and a low profile is preferred. The high output, cool running operation,
and good color rendering properties of this light make it an ideal replacement for older, bulkier, and less reliable HID and halogen light fixtures.
Durability/Mounting: The HAL-48-33W-LED hazardous location LED light is constructed of extruded aluminum with a tough powder coat finish
for high strength and durability. The housing is IP54 rated, providing limited ingress protection against dusts, and basic protection against
splashing water such as rain. This design is weather resistant, suitable for indoor or outdoor applications, and ideal for areas where wetness or
dusty conditions are commonly encountered.
The LEDs in this unit are Cree X-Lamp XR-E units that have been chosen for their high lumen per watt ratio and extreme long life. These Cree
LEDs provide over 90 lumens per watt output and have a 70% lumen retention at 50,000 hours, giving them better efficiency and operational life
than comparable LEDs.
Mounting for this unit is provided by two standard adjustable end brackets that allow operators to mount the light to flat surfaces and then adjust
the light 170° vertically for the best placement. The entire assembly weighs 2.8 lbs and measures 46.88 inches in length, and 2.68 inches wide
and 1.69 inches deep, making it ideal for mounting in areas where space is limited and a low profile fixture more readily installed.
Wiring/Power: These hazardous area LED lights are equipped with 6 feet of cord containing a standard two wire (White+ Black-) connecting
configuration. These lights operate from 12 or 24 volt DC current at 33.6 watts 2.64 amps on 12 VDC and 1.32 amps on 24 VDC.
Versatility: The HAL-48-33W-LED is ETL approved for Class 1 Division 2 groups A, B, C and D locations. This unit carries an IP54 water
resistant rating ensuring protection against limited ingress from dusts, dirt, and basic protection against light water spray landing directly on the
fixture. This light is ideal for indoor or outdoor applications and industrial operations with hazardous location classification where dusty or wet
conditions are commonly encountered.
Page: 1
Larson Electronics LLC www.LarsonElectronics.com
9419 E US HWY 175, Kemp, TX 75143 Phone: 903.498.3363 Fax: 903.498.3364 Email: sales@LarsonElectronics.com
Specifications / Additional Information
HAL-48-33W-LED Hazardous Location LED LightingETL Listed
Lamp Type: LEDClass 1 Division 2 Groups A,B,C,D
Dimensions: 46.88"-L 2.68" -W 1.69"- DCSA 22.2 No. 250.0
Weight: 2.8lb | 1.2 k g598
Watts: 33.6IP54 Ingress Protection
Voltage: 12-24 VDCT3 Temperature Rating
Lumens: 2416
Lamp Life Expectancy: 100,000 Hours
CRI: 75
Amps: 2.64 A @12 VDC | 1.32 A @ 24 VDC
Light Color: 6500KSpecial Orders- Requirements
Beam Type: 100° Flood or 30° SpotContact us for special requirements
Mounting: Standard Triangle End BracketsToll Free: 1-800-369-6671
Temp Range: -40°C – +85°CIntl: 1-903-498-3363
Wiring: 6Ft Lead | White: + Black: -E-mail: sales@larsonelectronics.com
3 year warranty replacement on this LED light. After 30 days, the
customer ships the failed LED light and/or LED bulb to Larson
Electronics at their expense. If the failure is a manufacturer defect, we
will ship a new replacement to the customer. If failure occurs within 30
days of receipt, Larson Electronics will provide a return label via email
to the customer. When the failed light is returned, Larson Electronics
will ship a new replacement.
Scroll Down to Purchase-
Page: 2
Larson Electronics LLC www.LarsonElectronics.com
9419 E US HWY 175, Kemp, TX 75143 Phone: 903.498.3363 Fax: 903.498.3364 Email: sales@LarsonElectronics.com
Buy American Compliant
The Larson Electronics HAL-48-33W-LED-UVA is a low voltage ultraviolet hazardous location lighting solution approved for Class 1
Division 2 environments and UL 1598 listed for use in wet locations. This powerful 46.88" long LED strip light produces 19,200 mW
radiant intensity, operates on 12 or 24 VDC, and is suitable for hazardous locations where UV lamps are used in paint and adhesive
curing, food inspection or for non-destructive testing.
The HAL-48-33W-LED-UVA is designed to provide a high output and ruggedly durable lighting solution for applications where ultraviolet light is
needed and Class1 Division 2 compliance is required. This low voltage hazardous location UV light that emits light in the ultraviolet spectrum.
This 365NM strip light can be operated on either 12 or 24 volt DC current and includes 6 feet of connecting lead with standard two wire
configuration. The housing is constructed of powder coated extruded aluminum for excellent strength and durability and is rated IP54 for
protection against exposure to splashing water and limited dust ingress. These units are configured in a 46.88" long strip or "bar" profile for
installation in locations where wide dispersal and a low profile is preferred. The high output, cool running operation, and good color rendering
properties of this light make it an ideal replacement for older, bulkier, and less reliable HID and halogen light fixtures.
The HAL-48-33W-LED-UVA uses LED light technology, a technology that is far better in energy saving than traditional fluorescent bulbs used for
the same purposes. Traditional ultraviolet lights require a coating to block out visible light or a special composition of gases and chemicals used
to create a higher concentration of ultraviolet light. This process, however, also produces many other wavelengths of light which go unused and
end up as wasted energy. LED lights are unique in that they have a narrower wavelength band than traditional ultraviolet sources and therefore
do not require these special coatings. As a result, LED lights do not produce unused, wasted light and therefore consume less energy than
traditional UV lights on the market. LED lights have the added benefit of being capable of producing very specific wavelengths with tighter curves
and are more durable and light weight as well.
The Class 1, Division 2 LED ultraviolet light fixture can be used for non-destructive testing in aviation and manufacturing, food processing and
inspection, and in paint, coating, and adhesive curing. The HAL-48-33W-LED-UVA provides operators in hazardous locations with a reliable and
durable UV lighting solution that combines effective production of UV light with explosion proof protection and is applicable for leak detection,
paint spray booths, ink, coatings, and adhesive curing, non-destructive testing, inspection, and food processing.
Ultraviolet Wavelength: Ultraviolet A Wavelength produces a longer wave between the 400nm - 315nm spectrum. This explosion proof LED
light has a peak wavelength of 365NM.
Durability: The HAL-48-33W-LED-UVA hazardous location LED light is constructed of extruded aluminum with a tough powder coat finish for
high strength and durability. The housing is IP54 rated, providing limited ingress protection against dusts, and basic protection against splashing
water such as rain. This design is weather resistant, suitable for indoor or outdoor applications, and ideal for areas where wetness or dusty
conditions are commonly encountered.
Mounting: Mounting for this unit is provided by two standard adjustable end brackets that allow operators to mount the light to flat surfaces and
then adjust the light 170° vertically for the best placement. The entire assembly weighs 2.8 lbs and measures 46.88 inches in length, and 2.68
inches wide and 1.69 inches deep, making it ideal for mounting in areas where space is limited and a low profile fixture more readily installed.
Wiring/Power: These hazardous area ultraviolet LED lights are equipped with 6 feet of cord containing a standard two wire (White+ Black-)
connecting configuration. These lights operate from 12 or 24 volt DC current at 33.5 watts drawing 2.8 amps on 12 VDC and 1.4 amps on 24
VDC.
Versatility: The HAL-48-33W-LED-UVA is ETL approved for Class 1 Division 2 groups A, B, C and D locations. This unit carries an IP54 water
resistant rating ensuring protection against limited ingress from dusts, dirt, and basic protection against light water spray landing directly on the
fixture. This light is ideal for indoor or outdoor applications and industrial operations with hazardous location classification where dusty or wet
conditions are commonly encountered.
Page: 3
Larson Electronics LLC www.LarsonElectronics.com
9419 E US HWY 175, Kemp, TX 75143 Phone: 903.498.3363 Fax: 903.498.3364 Email: sales@LarsonElectronics.com
Specifications / Additional Information
HAL-48-33W-LED-UVA Hazardous Location LED LightingListings/Ratings
Lamp Type: LEDClass 1 Division 2 Groups A,B,C,D
Dimensions: 46.88"-L 2.68" -W 1.69"- DUL 844
Weight: 2.8lb | 1.2 k gUL 1598
Watts: 33.6CSA 22.2 No. 137
Voltage: 12 or 24 VDCCSA 22.2 No. 213
Total Intensity: 19,200 mWCSA 22.2 No. 250.0
Efficacy: 573 mW/wIP54 Ingress Protection
Lamp Life Expectancy: 50,000 HoursT3 Temperature Rating
Amps: 2.80 A @12 VDC | 1.40 A @ 24 VDC
Light Color: 365NM - UltravioletSpecial Orders- Requirements
Beam Type: 100° FloodContact us for special requirements
Mounting: Standard Triangle End BracketsToll Free: 1-800-369-6671
Temp Range: -40°C – +85°CIntl: 1-903-498-3363
Wiring: 6Ft Lead | White: + Black: -E-mail: sales@larsonelectronics.com
3 year warranty replacement on this LED light. After 30 days, the
customer ships the failed LED light and/or LED bulb to Larson
Electronics at their expense. If the failure is a manufacturer defect, we
will ship a new replacement to the customer. If failure occurs within 30
days of receipt, Larson Electronics will provide a return label via email
to the customer. When the failed light is returned, Larson Electronics
will ship a new replacement.
Scroll Down to Purchase-
Part #: HAL-48-33W-LED (50936)
Page: 4
Larson Electronics LLC www.LarsonElectronics.com
9419 E US HWY 175, Kemp, TX 75143 Phone: 903.498.3363 Fax: 903.498.3364 Email: sales@LarsonElectronics.com
Page: 5
Larson Electronics LLC www.LarsonElectronics.com
9419 E US HWY 175, Kemp, TX 75143 Phone: 903.498.3363 Fax: 903.498.3364 Email: sales@LarsonElectronics.com
Links (Click on the below items to view):
- Dimensional Drawing
- STEP
- DXF
Page: 6
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.