GVP-48-2L-LED-G3
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com
1 of 2
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Wiring to the unit is loose
---
Confirm fixture is properly grounded
Dimmable 23 Watt Vapor Pr oof LE D 4 Foot Light
Instruction Manual
Do not attempt operation until you are familiar with all warni ngs , preca uti ons , and proc edur es out lin ed with in t his
instruction sheet. Read carefully before operating. Retain these instructions for future reference.
CAUTION
• Risk of fire/electrical shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
• Edges may cut. Handle with care.
SAFETY INSTRUCTIONS (Read Carefully for your Protection)
• ETL listed for indoor use only.
• Connect fixture to voltage on nameplate. Universal voltage 90-132VAC 50/60 Hz or 220-240VAC depending on
model purchased.
• A qualified electrician or person with experience in household wiring should install this fixture. The electrical
system and the method of connecting to electricity must be in accordance with the Natio
local building codes.
• Keep away from flammable objects. Do not position fixture within one inch of any combustible materials.
• Your light fixture is prewired for easy installation.
• This fixture is rated for 50,000+ hours.
• Wear rubber sole shoes and work on a sturdy wooden ladder.
• To avoid hazard to children, account for all parts and destroy packing materials.
nal Electrical Code and
PREPARATION
• Before beginning assembly, installation, or operation of product, make sure all parts are present.
Compare parts with the package contents list and diagram.
• If any part is missing or damaged, do not attempt to assemble, install or operate the product.
TROUBLESHOOTING
Light does not come on No power to the fixture Check if circuit breaker is tripped
QUESTIONS, PROBLEMS, MISSING PARTS
Before returning your fixture, please call Larson Electronics at 1-800-369-6671 or log on to
http://www.larsonelectronics.com for replacement parts.
WARNING
• Always hire a licensed electrician for proper installation.
• Always mount this fixture to a grounded junction/breaker box.
LIGHT ASSEMBLY
1. Turn off the power at the main fuse or breaker box.
2. Thread wires through wire gland and back cover wire hole.
3. Connect the wires to the wire terminal L to L, N to N then fasten the wire gland.
4. Connect 0-10V dimmer to associated wires. These are typically purple and grey but may differ per model.
Purple is positive (+) and grey is negative (-). Refer to dimmer instructions for connections. Please note: The
dimmer switch must be installed outsi de hazardous areas or use appropriate dimmer switch that meets area
classifications. Do not connect high voltage to dimmer wires!
5. Attach to the LED tubes to the lamp holder.
6. Put the tube fixing board in the back cover, fixing poles through the board’s holes. Then turn around the
head of fixing poles 90° to fix the board to back cover.
GVP-48-2L-LED-G3
Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com
2 of 2
7. Use the lens and back cover clips to attach lens to back cover.
8. Use the wall fixing clips to fix the light fixture to the wall.
9. Turn on power at main fuse breaker box.
LIGHT ASSEMBLY DIAGRAM
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Loading...