Larson Electronics EPL-PM-150LED-100-1227-1523 User Manual

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

150 Watt Class 1 Div 1 Explosion Proof LED Light - Non-Spark Aluminum Base - 120-277V AC

Part #: EPL-PM-150LED-100

Page: 1

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Made in Texas

The EPL-PM-150LED-100 Explosion Proof LED Light from Larson Electronics is rated Class 1 Division 1-2 Groups C & D and Class 2
Division 1-2 and uses a 16 inch LED light head to produce 13,000 lumens of light while drawing only 150 watts.

The EPL-PM-150LED-100 explosion proof LED light provides 9,000 square feet of work area coverage with 13,000 lumens of light output. This
portable LED light is mounted to an A-frame style aluminum base and has an adjustable LED light head measuring 16 inches wide by 14 inches
high. The LED light head on this unit produces a brilliant flood pattern of light that is ideal for illuminating enclosed areas and hazardous locations
where flammable vapors, gases and dusts may be present.
This explosion proof LED light fixture is comprised of a 16 inch wide square LED light head mounted within a portable base stand fabricated from
non sparking aluminum with a convenient carrying handle built into the top of the stand. The aluminum A-frame is powder coated with glossy blue
finish for corrosion resistances and aesthetics. The lamp can be easily adjusted up or down 90 degrees and locked into position by simply
loosening the two hand screws located on either side of the light head and retightening them once the desired angle is found.

Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge

LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile housings to break during

operation and/or transportation. Instead of heating a small filament or using a combination of gases to produce light, light emitting diodes (LEDs)
use semi-conductive materials that illuminate when electric current is applied, providing instant illumination with no warm up or cool down time
before re-striking. Because there is no warm up period, this light can be cycled on and off with no reduction in lamp life.
LED lights run at significantly cooler temperatures than traditional metal halide and high pressure sodium lights and contain no harmful gases,
vapors, or mercury, making them both safer and more energy efficient. No extra energy is wasted in cooling enclosed work areas due to external
heat emissions from bulb type lights, and the operator risks associated with traditional lighting methods, such as accidental burns and exposure
to hazardous substances contained in the glass bulbs, are eliminated. In addition, LEDs are also safer for the environment as they are 100%
recyclable, which eliminates the need for costly special disposal services required with traditional gas burning and arc type lamps.
LED Drivers: Even in LED fixtures, heat is the single largest factor in premature light failure and color shifting. As a result, many manufacturers
reduce the output of their LEDs in order to reduce the amount of heat produced. Rather than lower light output or quality, Larson Electronics
addresses this problem with the addition of electronic LED drivers. These internal drivers provide the ability to automatically monitor and adjust
input current to maintain the correct LED voltage levels regardless of input levels across a specific range. This not only reduces the energy
dissipation, effectively lowering the operating temperature of the fixture, but also prevents AC over-voltage and short circuit loading making this
fixture virtually maintenance free. Because the electronic drivers allow the EPL-PM-150LED-RT to run at a cooler internal temperature and
regulates the electrical current, energy efficiency and LED service hours are maximized while at the same time reducing operating costs and
downtime incurred from the frequent servicing intervals required with other hotter running lights.
The explosion proof LED light fixture features multiple LED drivers which helps to increase the operational life of the fixture. With traditional LED
lights, in the event an LED array or driver fails, the entire fixture no longer illuminates. With the EPL-PM-150LED-RT series of explosion proof
lamps from Larson Electronics, each LED fixture contains six individual LED boards configured in a series of banks. Each bank contains two LED
on a single board with an individual driver. In the event of a driver failure, only one bank of LEDs will be effected while the other banks will
continue to operate. In the event that of an LED failure, the mating LED will continue to operate.

Click Photos to Enlarge

Page: 2

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

60° Beam Angle 125° Beam Angle Plug 140° Beam Angle Plug

Beam Angles: When used as a portable lighting solution, the varying beam angles are each individually ideal for several environments. The 60°

beam provides the most intense beam of the three options. It is perfect for narrow, confined spaces and is ideally suited for tank cleaning
purposes. It offers focused light to provide ample illumination to tight work spaces and other environments. The 125° beam offers a more diffused
source of light that is also less intense in brightness. It is a great general area work light and performs well when used for outdoor illumination.
The 140° beam offers a very wide lighting pattern and is ideal for situations where lighting distance is not a concern, but illumination of a wider
area and even light distribution is. The 140° beam is great for situations that call for working in close proximity to lights such as in a paint booth.
This explosion proof LED high bay produces a total of 13,000 lumens with a color temperature of 5600K standard and a color rendering index of
75 which produces colors and details much more accurately than high pressure sodium or mercury vapor luminaries. We also offer a 3000K
warm white and 4500K natural white color temperature options (longer lead times may apply for non-standard temperatures). This lamp uses
Cree LED units that have been chosen for their high lumen per watt ratio and extreme longevity. These Cree LEDs generate a robust 86.67
lumens per watt effective lumen output and have a 80% lumen retention at 60,000 hours, giving them better efficiency and operational life than
traditional light sources.
Field Serviceability: This explosion proof LED light fixture is field serviceable. All major internal components can be purchased from Larson
Electronics and installed by a licensed electrician with basic tools. With most explosion proof fixtures, the fixture must be returned to the
manufacturer for repair work, which presents downtime and long turn around times for repair work. Larson Electronics addresses this issue with
the EPL-PM-150LED-RT series with field serviceability, allowing operators to perform service work without having to return the fixture to the
manufacturer in the event of damage or failure.

Energy Consumption Comparison

Page: 3