Larson Electronics EPL-EMG-48-2L-T8-SFC, EPL-EMG-48-2L-T8-PND User Manual

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Explosion Proof Emergency Fluorescent light Combination - 4 foot - 2 T8 lamps - Class I, Div I

Part #: EPL-EMG-48-2L-T8

Made in the USA

The Larson Electronics EPL-EMG-48-2L-T8 Explosion Proof Emergency Lights & Fluorescent light Combination is U.S./Canada U.L.
approved Class 1 Division 1, Class 1 Division 2 and ideal for hazardous locations where flammable chemical/petrochemical vapors
exist or have the potential to exist.

The EPL-EMG-48-2L-T8 is a 4 foot long, 2 lamp, UL listed Class 1 Division 1 and Class 2 Division 1and 2 explosion proof fluorescent light which
is equipped with an added battery backup providing 90 minutes of emergency runtime. This T6 temperature rated fixture comes standard with
two T8 fluorescent lamps which produce a combined 5,500 lumens of light. This fixture is multi-voltage capable and provides operators in
hazardous locations with a reliable and durable lighting solution that provides explosion proof protection along with the security of an emergency
battery backup.

Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge

Page: 1

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

This fluorescent light works, mounts and is wired like our EPL-48-2L explosion proof fluorescent light fixtures. The main difference is that we
attach an extra Bodine ballast box to the unit that adds emergency light functionality to the fixture. This explosion proof emergency light will run
the standard 90 minutes after power is lost. The light recharges the battery once electrical power is restored. Standard configuration includes a
single emergency ballast that will run a single lamp at 2750 lumens for 90 minutes. For an additional charge, a second ballast can be added to
run a second lamp for 5500 total lumens output for 90 minutes. The battery backup unit includes a switched leg for turning the light fixture on/off
without kicking the unit into emergency mode.
NOTE ON LAMPS: This unit comes equipped with an electronic ballast and F32-T8/841 bulbs which produce 2750 lumens per bulb and have a
rated lifespan of 24,000 hours.
Additional mounting options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown in the
photos above. We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or
conduit).
Standard Bracket Mounts: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is set by
tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt hole at
the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or wall), the
light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg. The first picture shown
above illustrates the ballast side bracket and also shows the access caps for changing the bulbs. The second picture shows the bracket at the
opposite end of the fluorescent light.

Made in USA Quality Lamps

1. Each unit dielectrically tested.

2. Fixture arrives assembled and lamped to reduce installation time and
cost. Adjustable mounting brackets enable the operator to choose any
mounting angle for the fixture, where other models may only offer one
or three choices.

3. Fixture constructed of extruded corrosion resistant copper free
aluminum alloy.

4. Over-sized, finned ballast housing for 800 mA fixtures provides more
heat dissipation and extends ballast life. Larger ballast box
accommodates High Output lamp ballasts. Ballast housing easily
accessible and externally mounted. Top and bottom covers secured
with nuts and bolts, instead of threaded through holes, which can be
damaged with dirt.

5. Heavy gauge extruded aluminum reflectors with high gloss reflective
finish. Resists dents and corrosion.

6. A wrench is used to unscrew the end caps for relamping the fixture,
while other models require the “tap and knock off” method to loosen the
end cap.

7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp
protection.

F32-T8/841 – 32 watt, 2950 lumens per bulb, 30,000 hours life, 4100
Kelvin color (Suffix –T8)

Page: 2