Larson Electronics EPLC-24-4L-LED-HV-5600K User Manual

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Explosion Proof LED Lights on Cart w/ Wheels-2foot-4 LED lamps-Paint Spray Booth Certified

Part #: EPLC-24-4L-LED

Made in the USA
*PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO THIS LIGHT CART*

The Larson Electronics EPLC-24-4L-LED Explosion Proof LED Light Cart is U.S./Canada U.L. approved Class 1 Division 1, Class 2
Division 1 and offers exceptional LED lamp durability, efficiency, 50,000 hour lamp life, and versatile explosion proof protection for
operators working in hazardous locations.

The EPLC-24-4L-LED explosion proof light cart is UL listed Class 1 Division 1 and Class 2 Division 1 & 2 and offers the ability to quickly and
easily add light wherever it is needed. This unit incorporates the highly effective Larson Electronics EPL-24-4L-LED explosion proof fixture
equipped with four 15 Watt LED T-series tube lights into a mobile platform. The platform is constructed of corrosion resistant aluminum alloy, has
non sparking casters, and includes a Class 1 Div 1 Explosion Proof Switch with 50 foot of SOOW electric cable as well. This T6 temperature
rated explosion proof LED light cart offers superior LED benefits in the form of reduced operating and maintenance costs, extreme lamp life, and
high resistance to impacts and vibration.
This unit is an excellent lighting solution for operators who need full power illumination in areas where traditional fixed mount lighting is
obstructed or cannot effectively reach.

Page: 1

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge

Page: 2

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

There is no ballast in this unit and the included LED T-series lamps have a 50,000+ hour service life, both of which result in extreme efficiency,
cooler operation and greatly reduced maintenance costs. The solid state design of the LED lamps give this fixture superior resistance to damage
from vibrations and extremes in temperature as well as a lamp service life over twice that of standard T8 bulbs. The lamps are protected by heat
and impact resistant Pyrex tubes which provide added security against impacts and overspray. The light fixture is constructed of copper free
aluminum alloy and the entire unit ships with a 50' SOOW cord and explosion proof plug. The lamp reflectors are corrosion resistant heavy gauge
aluminum and coated with a high gloss 93% reflective finish. The cart allows the entire fixture to be adjusted through 270 degrees of rotation to
position the lights as needed.
These LED-T series 15 watt LED lamps produce more illumination per watt than standard T8 bulbs, but draw only 3/4 of current. A standard EPL­24-4L-T8 explosion proof fluorescent light, with a combined total of 68 watts, draws 0.57 amps @ 120 volts. The LED version of the same light,
with a total of 60 watts, draws only 0.5 amps. The EPLC-24-4L-LED is multi-voltage (not multi-tap) and works on the following voltages: 120 Volt
60 HZ, 220 Volt 50 HZ, 240 Volt 60 HZ, 277 Volts 60 HZ. The unit is also offered in low voltage to accommodate those who need voltage on 12
and 24 volts dc. An explosion proof switch comes standard with the EPLC-24-4L-LED, allowing for simple turning on/off while in a hazardous
area.
Suggested Applications: Paint Spray Booths, Aircraft maintenance, Oil drilling rigs, Refineries, Solvent and cleaning areas, Gas processing
plants, Chemical manufacturing, Waste treatment plants, Gas processing plants.

Made in USA Quality Superior LED Benefits

1. Extreme long life.

1. Each unit dialectically tested.

2. Fixture arrives assembled and lamped to reduce installation time and
cost. Adjustable mounting brackets allow the light fixture to be rotated
while on the cart through a wide degree of positions for optimal light
placement.

3. Fixture constructed of extruded corrosion resistant copper free
aluminum alloy.

4. No ballast box. No ballast to replace. We simply run the black wire to
one end of the bulb and white wire to the other.

5. Heavy gauge extruded aluminum reflectors with high gloss reflective
finish. Resists dents and corrosion.

6. A wrench is used to unscrew the end caps for relamping the fixture,
while other models require the “tap and knock off” method to loosen the
end cap.

7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp
protection.

8. Spring loaded sockets on both ends hold lamps firmly for maximum
shock and vibration protection.

2. High efficiency and low amp draw.

3. High durability and reliability.

4. Small size and light weight.

5. 100% recyclable.

6. No toxins-lead, mercury.

7. High light output..

8. Consistent color over time.

9. High Versatility.

10. No fragile glass used in construction.

12. Vibration/impact resistant.

Cart Features:

5” non sparking casters
Frame constructed of corrosion resistant aluminum
Adjustable fixture brackets to 270 degrees
50 foot SOOW electric cable
Class I, Div I Explosion Proof Switch

Page: 3