Larson Electronics EPL-48-216-SFC, EPL-48-216-PND User Manual

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Low Profile Surface Mount Explosion Proof Fluorescent Light - 20,000 Lumens - Paint Booth Approved

Part #: EPL-48-216

Made in the USA

The Larson Electronics EPL-48-216 Explosion Proof Fluorescent Light Fixture is U.S./Canada U.L. approved Class 1 Division 1
and Class 1 Division 2 for hazardous locations where flammable chemical/petrochemical vapors exist or have the potential to exist.
The unit carries a T6 temperature rating, it is also approved for Paint Spray Booths.

The EPL-48-216 fixture is a 4 foot long, 4 lamp, UL listed Class 1 Division 1 and Class 2 Division 1&2 explosion proof fluorescent light which is
also approved for use in paint spray booth applications. This T6 temperature rated fixture comes standard with four T5 high output fluorescent
lamps. The lamps are protected by heat and impact resistant Pyrex tubes and the fixture is constructed of copper free aluminum alloy. The lamp
reflectors are corrosion resistant heavy gauge aluminum and coated with a high gloss reflective finish. This fixture is multi-voltage capable and is
available with a variety of lamp options. The EPL-48-216 provides operators in hazardous locations with a reliable and affordable lighting solution
that provides the best explosion proof protection available without sacrificing light quality or fixture durability.

Click Image to Enlarge Click Image to Enlarge Click Image to Enlarge

Page: 1

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Click here to see the LED version of this fixture
Mounting Options: Unless otherwise specified, our standard, most popular configuration is the bracket end mounting shown enlarged below.

We also offer a pendant mount for those needing to suspend the fixture away from the ceiling surface (i.e. suspend from pipe or conduit).
Additional mounting configurations can be customized to meet the requirements on the application. Please contact us for special mounting
configurations.
Adjustable Surface Mount Brackets: Each bracket is cinched to the bracket mounting peg on each side of the light. The angle of the bracket is
set by tightening two cap screws on either side of the bracket. The cap screws act as a set screw. The bracket itself is mounted via a single bolt
hole at the top the bracket. There are two brackets, one on each end of the light. Once the brackets are mounted to a surface (ceiling, floor or
wall), the light fixture can be removed from the brackets by loosening the cap screws that hold the bracket to the mounting peg.
Suspension Mounting: Pendant mount fixtures hang from the ceiling and are suspended by rigid pipe. Each fixture features a 1/2” NPT junction
box on one end, and a 1/2” NPT adjustable L-bracket on the other end of the fixture. Operators bring rigid pipe down to the threaded mounting
hubs. Wiring is fed down through the rigid pipe to the junction box and tied in to the fixture’s lead wires, completing the electrical connection. The
adjustable L-shape mounting bracket provides support for the opposite end of the fixture.

Made in USA Quality Lamp Options

1. Each unit dialectically tested.

2. Fixture arrives assembled and lamped to reduce installation time and
cost. Adjustable mounting brackets enable the operator to choose any
mounting angle for the fixture, where other models may only offer one
or three choices.

3. Fixture constructed of extruded corrosion resistant copper free
aluminum alloy.

4. Over-sized, finned ballast housing for 800 mA fixtures provides more
heat dissipation and extends ballast life. Larger ballast box
accommodates High Output lamp ballasts. Ballast housing easily
accessible and externally mounted. Top and bottom covers secured
with nuts and bolts, instead of threaded through holes, which can be
damaged with dirt.

5. Heavy gauge extruded aluminum reflectors with high gloss reflective
finish. Resists dents and corrosion.

6. A wrench is used to unscrew the end caps for relamping the fixture,
while other models require the “tap and knock off” method to loosen the
end cap.

7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp
protection.

F54-T5/850/HO – 54 watt, 5000 lumens per bulb, 20,000 hours life,
5000 Kelvin color, CRI 85 RHA-UNV-254-LT5 Ballast is THD<10% and
HPF .98 (Suffix –50KT5)
F54-T5/841/HO - 50 watt, 4450 lumens per bulb, 20,000 hour life, 4100
Kelvin color, CRI 85 (Suffix -41KT5)

This light is also available with LED bulbs instead of fluorescent bulbs. Click here to view.

Page: 2

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Specifications / Additional Information

EPL-48-216 Explosion Proof Fluorescent Light Fixture Ratings/Approvals
Listing: United States - Canada Class I Division 1, Groups C and D T6
Dimensions: W-11.25" x L-52" x H-8.5 " Class I Division 2, Group A,B,C,D
Weight: 70 Lbs Class II, Division 1 & 2, Groups E,F,G
Voltage: Universal 120-277VAC 50/60 Hz UL 595 Marine Type (Saltwater)
Total Watts: 216W UL 844
Total Lumens: 20,000 UL 1598 Marine Type
Lamp Life Expectancy (Hrs): 20,000 (T5HO) Certified Canadian Standards
Luminous Efficiency (Lm/W): 95.59 (T5HO) Listed for Paint Spray Booths
Color Temp: 5000K or 41000K ABS Certified
Beam Angle: 150° California Title 24 Compliant
Ambient Operating Temp Range: -20°C to +70°C IP67 Rated - Waterproof
Operating Temp Rating: T6 Rated T6 Temperature Rating
Minimum Operating Temp: -30°C NEMA 4X
Maximum Case Temp: +90°C Approved for Confined Spares
Housing Material: Cast Aluminum End Caps, Aluminum Reflectors -

Copper Free

Lens Material: Hardened Borosilicate Glass Tubes
Gasket Material: Buna Rubber O-Rings Special Orders- Requirements
Mounting: Surface Standard - Pendant Optional Phone: [phone]
Wiring Hub: 1/2" NPT Toll Free: 1-800-369-6671
Warranty: 5 Years* Fax: [phone]
U.L Approval: U.S Certificate Canada Certificate E-mail: [e-mail]

*Temperatures above +65° C will diminish ballast life from 5 years to 3
years

*5 year warranty replacement on this light. After 30 days, the customer
ships the failed light to Larson Electronics at their expense. If the failure
is a manufacturer defect, we will ship a new replacement to the
customer. If failure occurs within 30 days of receipt, Larson Electronics
will provide a return label via email to the customer. When the failed
light is returned, we will ship a new replacement.

Scroll Down to Purchase-

Part #: EPL-48-216 (64357)

Page: 3

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Page: 4

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

Links (Click on the below items to view):

- Dimensional Drawing

- Manual

- STEP

- EASM

- Hi Res Image 1

- Hi Res Image 2

Page: 5

Larson Electronics LLC www.LarsonElectronics.com

9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]

- Hi Res Image 3

- Hi Res Image 4

- Hi Res Image 5

- Hi Res Image 6

Page: 6