PATIO ENCLOSURES • GAZEBOS • GARAGE DOORS
GrandVue
INSTALLATION INSTRUCTIONS
MODEL E900, E950
RECESS INSTALLATION
FOR SURFACE INSTALLATION, SEE PAGE 3.
READ THE COMPLETE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH INSTALLATION.
INSTALLATION MAY REQUIRE TWO PEOPLE.
INSTALLATION TOOLS
202220911
PHILLIPS SCREWDRIVER
C
D
A
MEASURING TAPE
C
D
POWER DRILL & BITS
NOTE: GrandVue
ordered with the
motorized system will
not include Pullchain.
PENCIL OR PEN
B
PART DESIGNATIONS
D
A Screen Cassette Assembly
B Side Guide Rails
B
D
CONTACT LARSON: 1.888.483.3768 • LARSONDOORS.COM
C Recess Mount Clips
D #8 x 3/4” (19mm) Phillips Pan Head Screw
SIDE VIEW
OUTSIDE
DOOR HEAD
INSIDE
D
C
SET SCREW
6"
A
C
C
A
B
B
D
A
D
Shorter Pile
GrandVue RECESS INSTALLATION
MOUNTING THE SCREEN CASSETTE
On a recess installation, the Screen Cassette Assembly will be fastened to the
1
inside top with Recess Mount Clips. Measure how deep into the frame you wish
the Cassette Assembly to be installed. Using the #8 x 3/4”(19mm) Phillips Pan
Head Screws, attach the Mount Clips to the top approximately 6” in from each
side. For wider openings, space any remaining clips evenly along the top.
1A
1B
Make certain that the Set Screws are facing the front (1A). With clips screwed
to the jamb securely, position the Screen Casette Assembly so that the back
flanges of the Mount Clips fit into the groove at the top and back of the Cassette
Assembly (1B). Then bring the front of the Casette up, so that the top of the
Cassette Assembly is flat against the clips. With the Cassette Assembly positioned
correctly within the opening, tighten the Mount Clip Set Screws so that the
Cassette Assembly is secure and straight within the opening (1C).
PAGE 2
1C
INSTALLING THE SIDE GUIDE RAILS
Slide the top end of both Side Guide Rails onto the nylon tabs that protrude from
2
the End Caps of the Screen Cassette Assembly with the shorter pile to the inside
and with the plastic end cap toward the sill (2A). (NOTE: make sure the left and
right edges of the Screen and Screen Pull Bar are inside the Side Guide Rails).
Attach the Side Guide Rails to the opening using #8 x 3/4”(19mm) Phillips Pan
Head Screws (2B).
2A
MOTORIZED SCREENS: If you purchased a motorized screen you will need to
set the limits (the start and stop points of the screen) once the screen is
installed. Please see the separate operating instructions that accompanied your
remote control.
Inside
Outside
2B
GrandVue SURFACE INSTALLATION
FOR RECESS INSTALLATION, SEE PAGE 1
INSTALLATION TOOLS
PAGE 3
PHILLIPS SCREWDRIVER
E
D
MEASURING TAPE
A
E
D
POWER DRILL & BITS
NOTE: GrandVue ordered
with the motorized system will
not include Pullchain.
PENCIL OR PEN
B
D
F
B
D
F
PART DESIGNATIONS
A Screen Cassette Assembly
B Side Guide Rails
D #8 x 3/4”(19mm) Phillips Pan Head Screw
E Surface Mount ‘L’ Clips
F Screw Covers
CONTACT LARSON: 1.888.483.3768 • LARSONDOORS.COM
A
E
E
6"
6"
A
D
E
E
D
A
B
A
B
D
F
GrandVue SURFACE INSTALLATION
Outside
Shorter Pile
MOUNTING THE SCREEN CASSETTE
Slide the Surface Mount ‘L’ Clips into the back channel on
1
the top of the Screen Cassette (1A).
1A
Using the #8 x 3/4”(19mm) Phillips Pan Head Screws,
attach the Mount Clips approximately 6” in from each
side. For wider openings, space any remaining clips evenly
along the top (1B).
PAGE 4
1B
INSTALLING THE SIDE GUIDE RAILS
Slide the top of the Side Guide Rails onto the tabs
2
protruding from the End Caps of the Screen Cassette
Assembly with the shorter pile to the inside and with the
plastic end cap toward the sill (2A). Use an 1/8” drill bit
and first drill through both sides of the Side Guide Rails
where they are to be fastened. Next, using a 3/8” bit, drill
through the outside face only. This will allow you to snap
2A
2B
the Screw Covers in place. Square and attach Side Guide
Rails with #8 x 3/4”(19mm) Phillips Pan Head Screws
and Screw Covers. (2B).
MOTORIZED SCREENS: If you purchased a motorized
screen you will need to set the limits (the start and stop
points of the screen) once the screen is installed. Please see
the separate operating instructions that accompanied your
remote control.
Inside
Loading...