. .
, .
Assembly Instruction Sheet
Please go to our website f or product cleaning tips. Go to the
Tools Re quir ed: Flathead screwdriver, Phillips screwdriver, pl iers , wire cutters, wire stri pper s, electrical tape,
safety glasses.
Light So urce :
Estimated Assembly Time:
Preparation:
below to be sure all pa rts are present. If any parts ar e missin g or damaged, do not attempt to assemble, in stal l, or
operate the fixture. Contact cu stomer service fo r replac emen t parts.
(5) Candel abra Base 60W Max imum
20-30 mi nute s
Identify and ins pect all par ts before beg inni ng installation. Chec k packag e conten t list and diagra ms
Care + Maintenance
selection.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before i nsta llat ion. C onsu lt a lic ense d electrician if in doubt.
These instructions are provided for your safety. It is very import ant yo u read t hem co mple tely b efor e installing
the fixture. We strongly recommend that a licensed, profe ssio nal el ectr icia n perf orm th e installation.
Disconnect fixture from power source before replacing bu lbs. M ake su re bul bs are g iven s uff icient time to cool
before removal. Do not subject glass parts to any shock while in o pera tion o r shat teri ng may r esul t.
Package Contents
A
G
Part
A Crossbar
B
C
D
E
F
G
H
I
J
Description
Nipple
Lock Washer
Hex Nut
Ceiling Canopy
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Fixture Body
Fixture Loop Assembly
Quantity
1 pc.
1 pc.
2 pcs.
2 pcs.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
1 pc.
H
B
I
C
D
E
J
F
Thank you for purchasing thisproduct.
Need assistance with parts or assembly? Call our customer service or visit our website
1of6
FINISH: TUSCAN BROWN
GND
2.4 m m 13Ga
5.5” Dia.
1"
1
Overall Height 63”
(Includes 48” Chain)
(5) 60W Candelabra
Base Bulbs
(No Supplied)
14”
24” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
NO.
1
REPLACEMENT PART DESCRIPTION
CHAIN TU SCAN BROWN 4' 3.8MM
2of6
REQ.
1
Assembly Instruction Sheet
STEP 1 Adjust Fixture Assembly-
A. Unfold support arms on fixture assembly to proper
locations.
STEP 2 - Attach Fixture Loop Assembly to
Fixture Body
A. Thread Fixture Loop Assembly (J) to Fixture Body (I).
Tighten until snug.
Figure 1
Figure 2
Fixture Loop
Assembly
STEP 3 - Attach Crossbar to Outlet Box
A. Secure the Crossbar (A) to the outlet box with outlet
box screws (not supplied). Tighten until snug.
Mounting
Hole
Fixture
Body
Outlet Box
Crossbar
Outlet Box
Screw (not
Supplied)
Figure 3
Thank you for purchasing thisproduct.
Need assistance with parts or assembly? Call our customer service or visit our website
3of6
Assembly Instruction Sheet
STEP 4 Attach Nipple to Crossbar-
A. Thread one Hex Nut (D) onto the top end of the Nipple
(B).
B. Place one Lock Washer (C) over the top end of the
Nipple (B) and then thread the Nipple (B) into the center
lock hole of the Crossbar (A).
C. Using pliers, thread the hex Nut (D) against the
Crossbar (A) and hand tighten until snug.
Crossbar
Lock Washer
Hex Nut
Nipple
Figure 4
STEP 5 - Attach Canopy Chain Loop to Nipple
A. Thread another Hex Nut (D) onto the end of the Nipple
(B).
B. Place the Lock Washer (C) over the end of the Nipple
(B) and then thread the Canopy Chain Loop (F) onto the
end of the Nipple (B).
C. Using pliers, thread the Hex Nut (D) against the
Canopy Chain Loop (F) and hand tighten u ntil s nug.
STEP 6 Assemble Ceiling Canopy-
A. Push the Ceiling Canopy (E) upward over the Outlet
Box. Thread the Canopy Lock Ring (G) onto the Canopy
Chain Loop (F) and tighten until snug to secure the
Ceiling Canopy (E).
Outlet Box
Nipple
Crossbar
Hex Nut
Lock Washer
Canopy
Chain Loop
Figure 5
Outlet Box
Canopy Chian Loop
Ceiling Canopy
Canopy
Lock Ring
Thank you for purchasing thisproduct.
Need assistance with parts or assembly? Call our customer service or visit our website
4of6
Figure 6
Assembly Instruction Sheet
STEP 7 Attach Fixture Chain to Canopy
-
Chain Loop and Fixture Loop
A. Adjust the Fixture Chain (H) to your desired length by
removing the links if needed. You may need to use plier
to open the chain links. If so, put a cloth over the chain
to protect the finish from the pliers.
B. Attach one end of the Fixture Chain (H) onto the
Canopy Chain Loop (F) and then attach the other end of
the Fixture Chain (H) onto the Fixture Loop on the top of
the Fixture Loop Assembly (J).
STEP 8 Pass Supply Wires through Fixture
-
Chain
A. Pull the Supply Wires and Ground Wire up through the
Fixture Chain (H) alternating links. Push the wires up
through the Canopy Chain Loop (F) into the outlet box.
Fixture Loop
Fixture Loop
Assembly
Canopy Chain Loop
Fixture Chain
Supply Wire and
Ground Wire
Figure 7
Canopy Chain
Loop
Fixture Chain
Supply Wire
and Ground Wire
Figure 8
Thank you for purchasing thisproduct.
Need assistance with parts or assembly? Call our customer service or visit our website
5of6
Assembly Instruction Sheet
STEP 9 - Make Wire Connections
A. Un-thread the Canopy Lock Ring (G) and slide Canopy Lock
Ring (G) and Ceiling Canopy (E) down the Fixture Chain (H).
B. Push all slack fixture wire through Canopy Chain Loop (F)
into Outlet Box. Trim excess fixture wire leaving a minimum
of 6 inch. Hanging out of the Outlet Box.
C. Use standard wire connectors to make all wire connections.
(Connectors are not included with fixture.) Strip and prep are
wire ends according to instructions supplied with co nnec tors .
D. Connect White Supply Wire from the Outlet Box to Ribbed
Side Wire from fixture.
E. Connect Black (or Red) Supply Wire from the Outlet Box to
Smooth Side Wire from fixture.
F. Connect Ground Wire from the Outlet Box to Ground Wire
from fixture.
G. Twist connectors until wires are tightly joined together.
H. Wrap each connection with approved elec tric al tap e and
carefully stuff all the connected wires into the Outlet Box .
G. Re-attach the Ceiling Canopy (E) as shown in Step 6.
Supply Wire
and Ground
Wire from
Outlet Box
Supply Wire and
Ground Wire
Canopy Chain Loop
Fixture Chain
Ceiling Canopy
Canopy Lock Ring
Whit e wire fr om supp ly
Blac k wire fr om supp ly
(or Re d)
Grou nd wire f rom sup ply Grou nd wire f rom fix ture
Ribb ed side w ire
from f ixtur e
Smoo th side w ire
from f ixtur e
Figure 9
STEP 10 - Install Bulb
A. This fixture uses standard bulbs with a standard screw
base. Maximum 60 watts.
B. Insert bulb and screw properly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Figure 10
Bulb
Socket
Figure 11
Thank you for purchasing thisproduct.
Need assistance with parts or assembly? Call our customer service or visit our website
Loading...