Page 1
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
INSTALLA TIONINSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1 ． Return the nine arms to suitable position, see figure.2.
2 ． Attach column (B) with loop (A) to the fixture center body (C) by
turning it clockwise until tight.
3 ． Thread the pipe nipple (G) into bottom center of the fixture body (C),
Raise the lower frame (H) to bottom center of the fixture body (C),
aligning the hole with pipe nipple and screw it with finial (I).
4 ． Place the glass shade (D) on to the socket of the fixture body (C), and
then place the ring (E) and the screw shell (F) securely tighten.
5. Install the light bulbs in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED
HANGING
HANGING
HANGING
HANGING THE
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
(
Fig.
(
Fig.
( Fig.
Fig. 1)
(
Fig.
(
Fig.
( Fig.
Fig. 2)
1)
1)
1)
2)
2)
2) .
.
.
.
WATTAGE!
1. Shut off the power at the circuit breaker and remove old
fixture from ceiling, including the old crossbar.
2. Provide a 1/4 ” IPS pipe with one end securely mounted to a beam
or a structural member. The other end should protrude through the
center of the outlet box as shown.
3. Assemble the ceiling loop, nipple, nuts and hickey to center
1/4 ” IPS support pipe and adjust overall length to allow the lock
collar to hold the canopy flush to the ceiling. When the
adjustments have been completed, secure the three ( 3) nuts, as
shown.
4. Attach the chain to the fixture loop. Slip the lock collar and
canopy over the upper end of the chain. Open the end link of the
chain and lift the fixture to attach to the ceiling loop and secure
the link.
5. Lace the fixture wires, ground wire and safety cable through the
chain and loop, exiting through the side of hickey. Run the safety
cable through the top of the outlet box and secure to structural
member.
Fig. 1
Fig. 2
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
Take the black wire from the ceiling junction box and the smooth wire
1.
leg from the fixture and twist bare ends together. Twist wire connector
onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire leg
of fixture wire. NOTE: Twist wires together in the same direction you
twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together as
step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the crossbar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and then
raise the canopy all the way to the ceiling. Raise the loop and thread
onto ceiling loop protruding through canopy
Your
Your
Your
Your installation
to
the
to
the
to
to the
the junction
THE
WIRES
THE
WIRES
THE WIRES
WIRES (
installation
installation
installation is
junction
junction
junction box
box
box
box and
(
Fig.
3
)
(
Fig.
3
)
( Fig.
Fig. 3
3 )
)
is
now
is
is now
complete.
now
complete.
now complete.
complete. Return
and
test
and
test
and test
test the
Return
Return
Return power
the
fixture.
the
fixture.
the fixture.
fixture.
power
power
power
Fig. 3
Loading...