Page 1
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
INSTALLA TIONINSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1 ． Return the five arms to suitable position, see figure.2.
2 ． Attach column (B) with loop (A)to the fixture center body (C) by
turning it clockwise until tight.
3 ． Thread the pipe nipple (G) into bottom center of the fixture body (C).
Raise the lower frame (H) to bottom center of the fixture body (C),
aligning the hole with pipe nipple and screw it with finial (I).
4 ． Place the glass shade (D) on to the socket of the fixture body (C), and
then place the ring (E) and the screw shell (F) securely tighten.
5 ． Install the light bulbs in accordance with the fixture specifications
NOTE:
NOTE:
NOTE:
NOTE: DO
HANGING
HANGING
HANGING
HANGING THE
1. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old crossbar.
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other end of nipple (C) with loop attached into crossbar (D) until
snug.
5. Place lock washer (B) over end of nipple protruding t hrough crossbar and
thread hex nut (A) onto nipple until tight.
6. Take this crossbar assembly and mount to ceiling junction box with
junction box screws (E). Tighten screws securely with screwdriver .
7. Us ing proper chain pliers to open one end link of the chain provided and
connect to the fixture loop (I). Close the link .
8. By measuring, determine correct number of links needed for proper
hanging height. Using proper chain pliers disconnect and discard
remaining chain.
9. Lace the fixture wires through the chain.
10. Slip loop collar (H) over the chain, then do the same with the canopy (G).
11. Open the other end link of the chain and hang the f ixture on the loop at
the ceiling. Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull until
taut.
13. Slide canopy (G) up flush to ceiling, secure using loop (H).
THE
THE
THE FIXTURE
DO
NOT
DO
DO NOT
THE
THE
THE FIXTURE
EXCEED
NOT
EXCEED
NOT EXCEED
EXCEED THE
FIXTURE
FIXTURE
FIXTURE (
FIXTURE
FIXTURE
FIXTURE (
(
Fig.
(
Fig.
( Fig.
Fig. 1)
(
(
( Fig.
THE
THE
THE SPECIFIED
.
Fig.
2)
.
Fig.
2)
Fig. 2)
2) .
.
SPECIFIED
SPECIFIED
SPECIFIED WA TT AGE!
1)
1)
1)
WA TT AGE!
WA TT AGE!
WA TT AGE!
Fig. 1
Fig. 2
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
Take the black wire from the ceiling junction box and the smooth wire leg
1.
from the fixture and twist bare ends together. T wist wire connector onto
end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire leg of
fixture wire. NOTE: Twist wires together in the same direction you twist
the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper), attach
this wire and the bare copper wire from the fixture together as step 1.If
junction box has no ground wire, attach the bare copper fixture wire to the
green ground screw on the crossbar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and then
raise the canopy (G) all the way to the ceiling. Raise the loop (H) and
thread onto ceiling loop protruding through canopy
Your
installation
Your
installation
Your
Your
installation
installation is
junction
junction
junction
junction box
THE
THE
THE WIRES
box
and
box
and
box and
and test
WIRES
WIRES
WIRES (
is
now
is
now
is now
now complete.
test
the
test
test the
fixture.
the
fixture.
the fixture.
fixture.
(
Fig.
3)
(
Fig.
3)
( Fig.
Fig. 3)
3)
complete.
complete.
complete. Return
Return
Return
Return power
power
power
power to
to
to
to the
the
the
the
Fig. 3
Loading...