White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
INSTALLA TIONINSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1 ． Return the six arms to suitable position, see figure.2.
2 ． Attach column (B) with loop (A) to the fixture center body (C) by
turning it clockwise until tight.
3 ． Thread the pipe nipple (G) into bottom center of the fixture body
(C). Raise the lower frame (H) to bottom center of the fixture
body (C), aligning the hole with pipe nipple and screw it with
finial (I).
4 ． Place the glass shade (D) on to the socket of the fixture body (C),
and then place the ring (E) and the screw shell (F) securely
tighten.
5. Install the light bulbs in accordance with the fixture specifications
NOTE:
NOTE:
NOTE:
NOTE: DO
HANGING
HANGING
HANGING
HANGING THE
1. Shut off the power at the circuit breaker and remove old fixture
2. Provide a 1/4 ” IPS pipe with one end securely mounted to a
3. Assemble the ceiling loop, nipple, nuts and hickey to center
4. Attach the chain to the fixture loop. Slip the lock collar and
5. Lace the fixture wires, ground wire and safety cable through the
DO
DO
DO NOT
from ceiling, including the old crossbar.
beam or a structural member. The other end should protrude
through the center of the outlet box as shown.
1/4 ” IPS support pipe and adjust overall length to allow the lock
collar to hold the canopy flush to the ceiling. When the
adjustments have been completed, secure the three ( 3) nuts, as
shown.
canopy over the upper end of the chain. Open the end link of the
chain and lift the fixture to attach to the ceiling loop and secure
the link.
chain and loop, exiting through the side of hickey. Run the safety
cable through the top of the outlet box and secure to structural
member.
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
NOT
EXCEED
NOT
EXCEED
NOT EXCEED
EXCEED THE
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
(
Fig.
2)
.
(
Fig.
2)
.
( Fig.
Fig. 2)
2) .
.
THE
SPECIFIED
THE
SPECIFIED
THE SPECIFIED
SPECIFIED WATTAGE!
(
Fig.
1)
(
Fig.
1)
( Fig.
Fig. 1)
1)
WATTAGE!
WATTAGE!
WATTAGE!
Fig. 1
Fig. 2
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
1. Take the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed
wire leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together
as step 1.If junction box has no ground wire, attach the bare
copper fixture wire to the green ground screw on the crossbar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy all the way to the ceiling. Raise the loop
and thread onto ceiling loop protruding through canopy
Your
Your
Your
Your
junction
junction
junction
junction box
THE
THE
THE WIRES
installation
installation
installation
installation is
box
and
box
and
box and
and test
WIRES
WIRES
WIRES (
is
now
is
now
is now
now complete.
test
the
test
the
test the
the fixture.
(
Fig.
3)
(
Fig.
3)
( Fig.
Fig. 3)
3)
complete.
complete.
complete. Return
fixture.
fixture.
fixture.
Return
Return
Return power
power
power
power to
to
to
to the
the
the
the
Fig. 3
Loading...