Page 1
Safety Cable
Fixture Wires
Hex Nuts
Hickey
Nipple
Ceiling Loop
Canopy
Lock Collar
Chain (End Link)
Safety Cable
120V,7W
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
INSTALLA TIONINSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1. Return the arms to suitable position .
2. Attach the pipe nipple with the hex nut(D) to the top coupling of the
fixture body(E) and securely tighten .
3. Attach the crown (C) over end pipe nipple of the fixture body ( E
lock it with the lamellar nut(B). Attach the loop(A) to the end pipe nipple
by turning it clockwise until tight.
4. Place the glass shade ( G ) on to the socket of the fixture body ( E ) and
lock it with the screw shell (F) securely tighten.
5. Raise the harp(J) to the bottom end of screw protrud ent and lock it with
the ball nut(I). Raise the light bulb (H 120V 7W) to the bottom socket
of the fixture body(E),this is light bulb including .Raise the glass(K)
and cover(L) to the bottom end of pipe nipple protrudent and lock
it with the hex nut(M),attach the cover(N) to the glass(K)
it with the finial(O).
6.
Install the light bulbs (no including) in accordance with the fixture
specifications . N
WATTAGE!
WATTAGE!
WATTAGE!
WATTAGE!
HANGING
HANGING
HANGING
HANGING THE
1. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old crossbar.
2. Provide a 1/4 ” IPS pipe with one end securely mounted to a beam
or a structural member. The other end should protrude through the
center of the outlet box as shown.
3. Assemble the ceiling loop, nipple, nuts and hickey to center 1/4 ” IPS
support pipe and adjust overall length to allow the lock collar to
hold the canopy flush to the ceiling. When the adjustments have
been completed, secure the three ( 3) nuts, as shown.
4. Attach the chain to the fixture loop. Slip the lock collar and
canopy over the upper end of the chain. Open the end link of the
chain and lift the fixture to attach to the ceiling loop and secure the
link.
5. Lace the fixture wires, ground wire and safety cable through the
chain and loop, exiting through the side of hickey. Run the safety
cable through the top of the outlet box and secure to structural
member.
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
1. Take the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire
leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together
as step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the crossbar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy all the way to the ceiling. Raise the loop and
thread onto ceiling loop protruding through canopy
Your
Your
Your
Your
junction
junction
junction
junction box
installation
installation
installation
installation is
box
box
box and
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
OTE:
N
OTE:
N
N OTE:
OTE: DO
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
THE
WIRES
THE
WIRES
THE WIRES
WIRES (
is
now
is
now
is now
now complete.
and
test
test
test the
the
the
the fixture.
and
and test
(
Fig.
(
Fig.
( Fig.
Fig. 2)
DO
NOT
DO
DO NOT
fixture.
fixture.
fixture.
EXCEED
NOT
EXCEED
NOT EXCEED
EXCEED THE
(
Fig.
1)
(
Fig.
1)
( Fig.
Fig. 1)
1)
(
Fig.
(
Fig.
( Fig.
Fig. 3)
complete.
complete.
complete. Return
2)
.
2)
.
2) .
.
3)
3)
3)
Return
Return
Return power
E
E
E ) and
and
THE
SPECIFIED
THE
SPECIFIED
THE SPECIFIED
SPECIFIED
power
power
power to
to
to
to the
lock
the
the
the
Fig. 3
Fig. 1
Fig. 2
Loading...