Page 1
INSTALLATION
Junction Box
(Screw)
Junction Box
(Screw)
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
INSTALLATION
INSTALLATION
INSTALLATION INSTRUCTIONS
F
or
F
or
F or
or Chain
Chain
Chain
Chain Hang
Hang
Hang
Hang OR
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
OR
Ceiling
OR
Ceiling
OR Ceiling
Ceiling Mount
Mount
Mount
Mount
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1. Attach the loop (A) to the top center pipe nipple of the fixture body
(B) by turning it clockwise until tight.
2. Put the socket sleeve (C) on to the socket .
3. Install the light bulbs in accordance with the fixture specifications
NOTE:
NOTE:
NOTE:
NOTE: DO
HANGING
HANGING
HANGING
HANGING THE
1. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old single bar.
2. Carefully unpack new fixture and lay all the parts on a clear
surface.
3. Thread the two mounting screw into the pre-drilled holes in the
single bar spaced the same distance apart as the holes in the
canopy .Attach the single bar to the Junction Box with the two
Junction Box Screws as shown. The side of the Mounting plate
marked "GND" must face to out.
4. Us ing proper chain pliers to open one end link of the chain
provided and connect to the fixture loop. Close the link .
5. By measuring, determine correct number of links needed for
proper hanging height. Using proper chain pliers disconnect and
discard remaining chain.
6. Lace the fixture wires through the chain.
7. Open the other end link of the chain and hang the f ixture on the
loop at the ceiling. Close the link.
8. Feed the fixture wires through the loop of the canopy and pull until
taut.
9. Slide canopy up flush to ceiling, lock it securely with the ball nut .
THE
THE
THE FIXTURE
DO
NOT
DO
DO NOT
THE
THE
THE FIXTURE
EXCEED
NOT
EXCEED
NOT EXCEED
EXCEED THE
FIXTURE
FIXTURE
FIXTURE (
FIXTURE
FIXTURE
FIXTURE (
THE
THE
THE SPECIFIED
(
Fig.
(
Fig.
( Fig.
Fig. 1)
(
Fig.
2)
(
( Fig.
.
Fig.
2)
.
Fig. 2)
2) .
.
SPECIFIED
SPECIFIED
SPECIFIED WATTAGE!
1)
1)
1)
WATTAGE!
WATTAGE!
WATTAGE!
Fig.
1
Fig.
1
Fig.
Fig. 1
1
Fig.
2
Fig.
2
Fig.
Fig. 2
2
**If
you
not
need
**If
you
**If
**If you
pause
pause
pause
pause and
1. Take out the bottom loop of the canopy, attach the nipple to the top
center coupling of the fixture body, then take the canopy to the
fixture body, lock it with the shim and hex nut until tight.
2. Attach the fixture body to the ceiling, lock it securely with the ball
nut.
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
1. Take the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire
leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together
as step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the single bar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy (G) all the way to the ceiling. Raise the loop
(H) and thread onto ceiling loop protruding through canopy
Your
Your
Your
Your
junction
junction
junction
junction box
not
you not
not need
and
refer
and
refer
and refer
refer to
installation
installation
installation
installation is
box
box
box and
assembly
need
assembly
need assembly
assembly the
to
Fig
to
to Fig
THE
THE
THE WIRES
and
and
and test
4.**
Fig
4.**
Fig 4.**
4.**
WIRES
WIRES
WIRES (
is
now
is
now
is now
now complete.
test
the
test
the
test the
the fixture.
the
fixture
the
fixture
the fixture
fixture loop
(
Fig.
3)
(
Fig.
3)
( Fig.
Fig. 3)
3)
complete.
complete.
complete. Return
fixture.
fixture.
fixture.
Return
Return
Return power
loop
loop
loop ,
power
power
power to
,
,
, please
please
please
please
to
to
to the
Fig
.
4
Fig
.
4
Fig
Fig .
. 4
4
the
the
the
Fig.
Fig.
Fig.
Fig. 3
3
3
3
Loading...