Page 1
Listed
U
L
R
INSTALLA TIONINSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING THE FIXTURE ( Fig. 2) .
1 ． Return the six arms to suitable position, see figure.2.
2 ． Attach the loop (A) to center of the fixture body (L) by turning
it clockwise until tight.
3 ． Thread the nipple (K) into the coupling (F) on bottom of the
fixture body (L), secure with the hex nut (G). Raise the lower
tube (H) and the finial base (I) to the bottom of the fixture body
(L), secure with the finial (J).
4 ． Fixed the arms (C) to the fixture body (L) with the ball nut (B).
5 ． Place the sleeve (D) onto the socket (E).
6 ． Install the light bulbs in accordance with the fixture’s
NOTE:
specifications. NOTE:
MAXIMUM
MAXIMUM
MAXIMUM
MAXIMUM WATT AGE
HANGING THE FIXTURE ( Fig. 1)
IMPORTANT:
IMPORTANT:
IMPORTANT:
IMPORTANT: For
must
be
must
must
must be
outlet
outlet
outlet
outlet box.
SUGGESTED INSTALLATION:
1. Shut off the power at the circuit breaker and remove old fixture
2. Provide a 1/4 ” IPS pipe with one end securely mounted to a
3. Assemble the ceiling loop, nipple, nuts and hickey to center
4. Attach the chain to the fixture loop. Slip the lock collar and
5. Lace the fixture wires, ground wire and safety cable through
CONNECTING THE WIRES ( Fig. 3)
1. Take the black wire from the ceiling junction box and the
2. Repeat same process with white junction box wire and ribbed
3. If your junction box has a grounding wire (green or bare
4. Tuck these wire connections nea t ly into the ceiling outlet box
installed
be
installed
be installed
installed by
box.
box.
box.
from ceiling, including the old crossbar.
beam or a structural member. The other end should protrude
through the center of the outlet box as shown.
1/4 ” IPS support pipe and adjust overall length to allow the lock
collar to hold the canopy flush to the ceiling. When the
adjustments have been completed, secure the three ( 3) nuts, as
shown.
canopy over the upper end of the chain. Open the end link of
the chain and lift the fixture to attach to the ceiling loop and
secure the link.
the chain and loop, exiting through the side of hickey. Run the
safety cable through the top of the outlet box and secure to
structural member.
smooth wire leg from the fixture and twist bare ends together.
Twist wire connector onto end of wire until snug.
wire leg of fixture wire. NOTE: Twist wires together in the
same direction you twist the wire connector onto wires.
copper), attach this wire and the bare copper wire from the
fixture together as step 1.If junction box has no ground wire,
attach the bare copper fixture wire to the green ground screw on
the crossbar.
and then raise the canopy all the way to the ceiling. Raise the
loop and thread onto ceiling loop protruding through canopy.
NOTE:
NOTE: DO
WATTAGE
WATTAGE
WATTAGE RATING!
For
a
safe
For
a
safe
For a
a safe
safe and
by
means
by
means
by means
means of
DO
NOT
DO
NOT
DO NOT
NOT EXCEED
RATING!
RATING!
RATING!
and
secure
and
secure
and secure
secure installation,
of
support
of
support
of support
support that
that
that
that is
EXCEED
EXCEED
EXCEED THE
installation,
installation,
installation, this
is
independent
is
independent
is independent
independent of
THE
THE
THE
this
fixture
this
fixture
this fixture
fixture
of
of
of the
Fig.1
Fig.1
Fig.1
Fig.1
the
the
the
Fig.2
Fig.2
Fig.2
Fig.2
Your installation is now complete. Return power to the junction
box and test the fixture.
Fig.3
Fig.3
Fig.3
Fig.3
Loading...