Page 1
INSTALLATION
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
INSTALLATION
INSTALLATION
INSTALLATION INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING THE FIXTURE ( Fig. 2) .
1 ． Return the six arms to suitable position, see figure.2.
2 ． Attach column (B) with loop (A) to the fixture center body (C) by
turning it clockwise until tight.
3 ． Thread the pipe nipple (G) into bottom center of the fixture body
(C). Raise the lower frame (H) to bottom center of the fixture
body (C), aligning the hole with pipe nipple and screw it with
finial (I).
4 ． Place the glass shade (D) on to the socket of the fixture body (C),
and then place the ring (E) and the screw shell (F) securely
tighten.
5 ． Install the light bulbs in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED
WATTAGE!
HANGING THE FIXTURE ( Fig. 1)
1. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old crossbar.
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other end of nipple (C) with loop attached into crossbar (D)
until snug.
5. Place lock washer (B) over end of nipple protruding t hrough crossbar
and thread hex nut (A) onto nipple until tight.
6. Take this crossbar assembly and mount to ceiling junction box with
junction box screws (E). Tighten screws securely with screwdriver .
7. Us ing proper chain pliers to open one end link of the chain provided
and connect to the fixture loop (I). Close the link .
8. By measuring, determine correct number of links needed for proper
hanging height. Using proper chain pliers disconnect and discard
remaining chain.
9. Lace the fixture wires through the chain.
10. Slip loop collar (H) over the chain, then do the same with the canopy
(G).
11. Open the other end link of the chain and hang the f ixture on the loop
at the ceiling. Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull
until taut.
13. Slide canopy (G) up flush to ceiling, secure using loop (H).
Fig. 1
Fig. 2
CONNECTING THE WIRES ( Fig. 3)
1. T ake the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire
leg of fixture wire. NOTE: Twist wires together in the same direction
you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together as
step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the crossbar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy (G) all the way to the ceiling. Raise the loop
(H) and thread onto ceiling loop protruding through canopy
Your
Fig. 3
installation
Your
installation
Your
Your
installation
installation is
junction
junction
junction
junction box
box
box
box and
and
and
and test
is
now
is
is now
test
test
test the
complete.
now
complete.
now complete.
complete. Return
the
fixture.
the
fixture.
the fixture.
fixture.
Return
Return
Return power
power
power
power to
to
to
to the
the
the
the
Loading...