Page 1
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING &
&
INSTALLATION
&
INSTALLATION
& INSTALLATION
INSTALLATION INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1. Attach the finial(E) to the top pipe nipple of fixture
body(F), attach the finial(G) to the fixture body's tube of
side, raise the cover(K) and finial(L) to the bottom pipe
nipple of fixture body, then lock them until tight.
2. Raise the ring ( H ) to top of the glass ( I ), carefully life the
glass assembly and spacer ring(M) to the lamp holder of
fixture body , lock it with the screw shell(J).
HANGING
HANGING
HANGING
HANGING THE
1. Shut off the power at the circuit breaker and remove
old fixture from ceiling, including the old hardware .
2. Carefully unpack new fixture and lay all the parts on a
clear surface.
3. Thread the two Studs(A) about 1/4 ” into the pre-drilled
holes in the Mounting strap spaced the same distance
apart as the holes in the canopy (B).
4. Attach the Mounting strap to the Junction Box with
the two Junction Box Screws as shown. The side of
the Mounting strap marked "GND" must face out.
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
1. Take the black wire from the ceiling junction box and
the smooth wire leg from the fixture and twist bare
ends together. Twist wire connector onto end of wire
until snug.
2. Repeat same process with white junction box wire and
ribbed wire leg of fixture wire. NOTE: Twist wires
together in the same direction you twist the wire
connector onto wires.
3. If your junction box has a grounding wire (green or
bare copper), attach this wire and the bare copper wire
from the fixture together as step 1.If junction box has
no ground wire, attach the bare copper fixture wire to
the green ground screw on the single bar .
4. Tuck these wire connections nea t ly into the ceiling
outlet box and then raise the fixture canopy all the
way to the ceiling.
5. Raise the canopy (B) onto the junction box, aligning
screws on mounting strap with mounting holes in
canopy and lock it securely with the ball nuts( C ).
6. Install the light bulbs in accordance with the fixture
specifications NOTE:
SPECIFIED
SPECIFIED
SPECIFIED
SPECIFIED WATTAGE.
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
THE
WIRES
THE
WIRES
THE WIRES
WIRES (
NOTE:
NOTE:
NOTE: DO
WATTAGE.
WATTAGE.
WATTAGE.
(
Fig.
(
Fig.
( Fig.
Fig. 2)
(
Fig.
1)
(
Fig.
1)
( Fig.
Fig. 1)
1)
(
Fig.
(
Fig.
( Fig.
Fig. 3)
DO
NOT
DO
NOT
DO NOT
NOT EXCEED
2)
2)
2)
3)
3)
3)
EXCEED
EXCEED
EXCEED THE
THE
THE
THE
F
F
F
F ig.
F
F
F
F ig.
ig.
1
ig.
1
ig. 1
1
(GND)
Ball (C)
ig.
2
ig.
2
ig. 2
2
Your
installation
Your
installation
Your
Your installation
installation is
the
junction
the
junction
the
the junction
junction box
Fig. 3
box
box
box and
is
now
is
now
is now
now complete
and
test
and
test
and test
test the
complete
complete
complete Return
the
fixture.
the
fixture.
the fixture.
fixture.
Return
Return
Return power
power
power
power to
to
to
to
Loading...