Page 1
INSTALLATION INSTRUCTIONS
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE
Listed
U
L
R
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING
ASSEMBLING
ASSEMBLING
ASSEMBLING THE
1. Put the glass shade (B) over the socket cup (A).
2. Put the check ring (C) into the glass shade (B) and cover the
socket.
3.
Thread the socket ring (D) on to the socket and secure the glass
shade.
HANGING
HANGING
HANGING
HANGING THE
1 Disconnect power at main electrical panel before installation.
2 ． Thread the two mounting screws about 1/4 ” into the pre-drilled
holes in the mounting plate, spaced about the same distance apart
as the holes in the fixture back plate. Attach the mounting plate to
the junction box using two junction box screws . The side of the
mounting plate marked “ GND ” must face out.
3. Guide fixture wires through hole in center of mounting plate then
cover the junction box with canopy, a ligning the s crew of
mounting plate with the hole of canopy and lock it with brass ball.
4. Us ing proper chain pliers to open one end link of the chain
provided and connect to the fixture loop (A). Close the link .
5. By measuring, determine correct number of links needed for
proper hanging height. Using proper chain pliers disconnect and
discard remaining chain.
6. Open the other end link of the chain and hang the fixture on the
loop at the ceiling. close the link.
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
THE
FIXTURE
THE
FIXTURE
THE FIXTURE
FIXTURE (
(
Fig.
(
Fig.
( Fig.
Fig. 3)
(
Fig.
(
Fig.
( Fig.
Fig. 1
3)
3)
3)
1
)
1
)
1 )
)
Fig.
Fig.
Fig.
Fig. 3
3
3
3
CONNECTING
CONNECTING
CONNECTING
CONNECTING THE
1. Take the black wire from the ceiling junction box and the smooth
wire leg from the fixture and twist bare ends together. Twist wire
connector onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire
leg of fixture wire. NOTE: Twist wires together in the same
direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together
as step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the crossbar.
4. Tuck these wire connections nea t ly into the ceiling outlet box and
then raise the canopy all the way to the ceiling.
5. Install the light bulbs in accordance with the fixture specifications
NOTE:
NOTE:
NOTE:
NOTE: DO
Your
installation
Your
installation
Your
Your
installation
installation is
junction
junction
junction
junction box
Fig.
2
Fig.
2
Fig.
Fig. 2
2
THE
THE
THE WIRES(
DO
NOT
DO
NOT
DO NOT
NOT EXCEED
box
and
box
and
box and
and test
WIRES(
WIRES(
WIRES( Fig.
EXCEED
EXCEED
EXCEED THE
is
now
is
now
is now
now complete
test
test
test the
Fig.
Fig.
Fig. 2)
complete
complete
complete Return
the
fixture.
the
fixture.
the fixture.
fixture.
2)
2)
2)
THE
SPECIFIED
THE
SPECIFIED
THE SPECIFIED
SPECIFIED WATTAGE.
Return
Return
Return power
power
power
power to
WATTAGE.
WATTAGE.
WATTAGE.
to
the
to
the
to the
the
Fig.
Fig.
Fig.
Fig. 1
1
1
1
Loading...