Page 1
ASSEMBLING
I
H
CHAIN
G
F
E
D
A
B
C
Junction
Box(Ceiling)
A
B
C
C
ASSEMBLING
ASSEMBLING
ASSEMBLING &
&
INSTALLATION
&
INSTALLATION
& INSTALLATION
INSTALLATION INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS PRODUCT
PRODUCT
PRODUCT
PRODUCT
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
ASSEMBLING THE FIXTURE ( Fig. 2) .
1. Return the arms to suitable position .
2. Attach the pipe(A) in to the column(H) , catch hold of end pipe(A) to top
coupling of lamp body(F) by turning it clockwise until tight. Raise the
pipe(G) to the bottom coupling of the lamp body(F) by turning it
clockwise until tigh . Attach the glass( E ) to the lamp holder, lock it
securely with the ring( D ).
3 . Attach the arm( B ) to the lamp body(F), aligning the arm's hole with the
screw hole of lamp body, lock them securely with the
4 . Install the light bulbs in accordance with the fixture specifications
NOTE: DO NOT EXCEED THE SPECIFIED
knob screw
WATTAGE
( C ).
!
HANGING THE FIXTURE ( Fig. 1)
1. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old single bar .
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other end of nipple (C) with loop attached into single bar (D)
until snug.
5. Place lock washer (B) over end of nipple protruding t hrough single bar
and thread hex nut (A) onto nipple until tight.
6. Take this single bar assembly and mount to ceiling junction box with
junction box screws (E). Tighten screws securely with screwdriver .
7. Us ing proper chain pliers to open one end link of the chain provided
and connect to the fixture loop (I). Close the link .
8. By measuring, determine correct number of links needed for proper
hanging height. Using proper chain pliers disconnect and discard
remaining chain.
9. Lace the fixture wires through the chain.
10. Slip loop collar (H) over the chain, then do the same with the canopy
(G).
11. Open the other end link of the chain and hang the f ixture on the loop
at the ceiling. Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull
until taut.
13. Slide canopy (G) up flush to ceiling, secure using loop (H).
Fig. 1
Fig. 2
CONNECTING THE WIRES ( Fig. 3)
1. Take the black wire from the ceiling junction box and the smooth wire
leg from the fixture and twist bare ends together. Twist wire connector
onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire leg
of fixture wire. NOTE: Twist wires together in the same direction you
twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper),
attach this wire and the bare copper wire from the fixture together as
step 1.If junction box has no ground wire, attach the bare copper
fixture wire to the green ground screw on the single bar .
4. Tuck these wire connections nea t ly into the ceiling outlet box and then
raise the canopy (G) all the way to the ceiling. Raise the loop (H) and
thread onto ceiling loop protruding through canopy .
Your
installation
Your
installation
Your
Your installation
installation is
box
and
and
and test
test
test
test the
box
box
box and
Fig. 3
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
is
now
is
now
is now
now complete.
the
fixture.
the
fixture.
the fixture.
fixture.
FIXTURE
WIRES
White or
Ribbed
complete.
complete.
complete. Return
HOUSE
WIRES
White
(Neutral)
Return
Return
Return power
FIXTURE
WIRES
Bare
Copper
(Ground)
power
to
the
to
the
to the
the junction
junction
junction
junction
power
power to
HOUSE
WIRES
Green or
Bare Copper(Ground)
U
R
Listed
L
Loading...