lapara LA-ITR-800-LCD, LA-ITR-1100-LCD, LA-ITR-2000-LCD, LA-ITR-1500-LCD, LA-ITR-2500-LCD User Manual
...
LA-ITR-800-LCD
LA-ITR-1100-LCD
LA-ITR-1500-LCD
LA-ITR-2000-LCD
LA-ITR-2500-LCD
LA-ITR-3000-LCD
Line Interactive Pure Sine Wave UPS
LA-ITR UPS User Manual
EN
________________________________________________________________________________
LA-ITR-LCD
1
Table of Contents
1. Important Safety Warning………………………………………………
2
1.1. Transportation
2
1.2. Preparation
2
1.3. Installation
2
1.4. Operation
2
1.5. Maintenance, Service And Faults
3
2. Installation And Setup……………………………………………………
4
2.1. Rear Panel View
4
2.2. Install The UPS
4
2.3. Setup The UPS
5
2.4. Battery Replacement
7
2.5. Battery Kit Assembly (Option)
8
3. Operations…………………………………………………………………..
10
3.1. Button Operation
10
3.2. LCD Panel
10
3.3. Audible Alarm
11
3.4. LCD Display Wordings Index
12
3.5. UPS Setting
12
3.6. Operating Mode Description
14
3.7. Faults Reference Code
15
3.8. Warning Indicator
15
4. Troubleshooting…………………………………………………………...
16
5. Storage And Maintenance……………………………………………….
18
6. Specifications………………………………………………………………
19
________________________________________________________________________________
LA-ITR-LCD
2
1. Important Safety Warning
Please comply with all warnings and operating instructions in this manual strictly. Save this
manual properly and read carefully the following instructions before installing the unit. Do not
operate this unit before reading through all safety information and operating instructions
carefully
1.1. Transportation
Please transport the UPS system only in the original package to protect against shock
and impact.
1.2. Preparation
Condensation may occur if the UPS system is moved directly from cold to warm
environment. The UPS system must be absolutely dry before being installed. Please
allow at least two hours for the UPS system to acclimate the environment.
Do not install the UPS system near water or in moist environments.
Do not install the UPS system where it would be exposed to direct sunlight or near
heater.
Do not block ventilation holes in the UPS housing.
1.3. Installation
Do not connect appliances or devices, which would overload the UPS system (e.g.
laser printers) to the UPS output sockets.
Place cables in such a way that no one can step on or trip over them.
Do not connect domestic appliances such as hair dryers to UPS output sockets.
The UPS can be operated by any individuals with no previous experience.
Connect the UPS system only to an earthed shockproof outlet that must be easily
accessible and close to the UPS system.
Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your
computer) to connect the UPS system to the building wiring outlet (shockproof outlet).
Please use only VDE-tested, CE-marked power cables to connect the loads to the
UPS system.
When installing the equipment, it should ensure that the sum of the leakage current of
the UPS and the connected devices does not exceed 3.5mA.
1.4. Operation
Do not disconnect the mains cable on the UPS system or the building wiring outlet
(shockproof socket outlet) during operations since this would cancel the protective
earthing of the UPS system and of all connected loads.
The UPS system features its own, internal current source (batteries). The UPS output
sockets or output terminals block may be electrically live even if the UPS system is not
connected to the building wiring outlet.
In order to fully disconnect the UPS system, first press the OFF/Enter button to
disconnect the mains.
Prevent no fluids or other foreign objects from inside of the UPS system.
________________________________________________________________________________
LA-ITR-LCD
3
1.5. Maintenance, Service and Faults
The UPS system operates with hazardous voltages. Repairs may be carried out only
by qualified maintenance personnel.
Caution - risk of electric shock. Even after the unit is disconnected from the mains
(building wiring outlet), components inside the UPS system are still connected to the
battery and electrically live and dangerous.
Before carrying out any kind of service and/or maintenance, disconnect the batteries
and verify that no current is present and no hazardous voltage exists in the terminals
of high capability capacitor such as BUS-capacitors.
Only persons are adequately familiar with batteries and with the required
precautionary measures may replace batteries and supervise operations.
Unauthorized persons must be kept well away from the batteries.
Caution - risk of electric shock. The battery circuit is not isolated from the input
voltage. Hazardous voltages may occur between the battery terminals and the ground.
Before touching, please verify that no voltage is present!
Batteries may cause electric shock and have a high short-circuit current. Please take
the precautionary measures specified below and any other measures necessary
when working with batteries:
remove wristwatches, rings and other metal objects
Use only tools with insulated grips and handles.
When changing batteries, install the same number and same type of batteries.
Do not attempt to dispose of batteries by burning them. This could cause battery
explosion.
Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and
eyes. It may be toxic.
Please replace the fuse only with the same type and amperage in order to avoid fire
hazards.
Do not dismantle the UPS system.
________________________________________________________________________________
LA-ITR-LCD
4
2. Installation And Setup
NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is
damaged. Please keep the original package in a safe place for future use.
2.1. Rear Panel View
LA-ITR-800-LCD / LA-ITR-1100-LCD /
LA-ITR-1500-LCD / LA-ITR-2000-LCD
LA-ITR-2500-LCD /
LA-ITR-3000-LCD /
1. Programmable outlets: connect to non-critical loads.
2. Output receptacles: connect to mission-critical loads.
3. AC input
4. Input circuit breaker
5. Network/Fax/Modem surge protection
6. Emergency power off function connector (EPO)
7. USB communication port
8. RS-232 communication port
9. SNMP intelligent slot
10. External battery connector (only available for L model)
11. External battery pack numbers detection port
2.2. Install the UPS
For safety consideration, the UPS is shipped out from factory without connecting battery wires.
Before install the UPS, please follow below steps to re-connect battery wires first.
Step 1
Step 2
Step 3
Remove front panel.
Connect the AC input and
re-connect battery wires.
Put the front panel back to the unit.
________________________________________________________________________________
LA-ITR-LCD
5
Rack-mount Installation
Step 1 Step 2
Tower Installation
Step 1
Step 2
Step 3
2.3. Setup the UPS
Step 1: UPS input connection
Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension
cords.
Step 2: UPS output connection
There two kinds of outputs: programmable outlets and general outlets. Please connect
non-critical devices to the programmable outlets and critical devices to the general outlets.
During power failure, you may extend the backup time to critical devices by setting shorter
backup time for non-critical devices.
Step 3: Communication connection
Communication ports:
USB port RS-232 port Intelligent slot
To allow for unattended UPS shutdown/start-up and status monitoring, connect the
communication cable one end to the USB/RS-232 port and the other to the communication
port of your PC. With the monitoring software installed, you can schedule UPS
shutdown/start-up and monitor UPS status through PC.
The UPS is equipped with intelligent slot perfect for either SNMP or AS400 card. When
installing either SNMP or AS400 card in the UPS, it will provide advanced communication and
monitoring options.
PS. USB port and RS-232 port cannot work at the same time.
Step 4: Network connection
Network/Fax/Phone surge port
________________________________________________________________________________
LA-ITR-LCD
6
Connect a single modem/phone/fax line into surge-protected “IN” outlet on the back panel of
the UPS unit. Connect from “OUT” outlet to the equipment with another modem/fax/phone line
cable.
Step 5: Disable and enable EPO function
Keep the pin 1 and pin 2 closed for UPS normal operation. To activate EPO function, cut the
wire between pin 1 and pin 2.
Step 6: External battery connection (for long-run models only)
Connect one end of external battery cable to UPS unit and the other end to battery box. Use
supplied battery detection wire in detection port of UPS unit and plug the other end to battery
bank. See below chart for detailed connection.
NOTE: Maximum connected external battery boxes up to 4 units.
Step 7: Turn on the UPS
Press the ON/Mute button on the front panel for two seconds to power on the UPS.
Note: The battery charges fully during the first five hours of normal operation. Do not
expect full battery run capability during this initial charge period.
Step 8: Install software
For optimal computer system protection, install UPS monitoring software to fully configure
UPS shutdown. Please follow steps below to download and install monitoring software:
1. Go to the website http://www.power-software-download.com
2. Click ViewPower software icon and then choose your required OS to download the
software.
3. Follow the on-screen instructions to install the software.
4. When your computer restarts, the monitoring software will appear as an orange plug icon
located in the system tray, near the clock.
It’s in closed status for UPS
normal operation.
UPS
Battery Box
Battery Box
________________________________________________________________________________
LA-ITR-LCD
7
2.4 Battery Replacement
NOTICE: This UPS is equipped with internal batteries and user can replace the batteries
without shutting down the UPS or connected loads (hot-swappable battery design).
Replacement is a safe procedure, isolated from electrical hazards.
CAUTION!! Consider all warnings, cautions, and notes before replacing batteries.
Note: Upon battery disconnection, equipment is not protected from power outages.
Step 1
Step 2
Step 3
Remove front panel.
Disconnect battery wires.
Pull out the battery box by
removing two screws on the front
panel.
Step 4
Step 5
Step 6
Remove the top cover of battery
box and replace the inside
batteries.
After replacing the batteries,
put the battery box back to
original location and screw it
tightly.
Re-connect the battery wires.
Step 7
Put the front panel back to the unit.
________________________________________________________________________________
LA-ITR-LCD
8
2.5 Battery Kit Assembly (option)
NOTICE: Please assemble battery kit first before installing it inside of UPS. Please select
correct battery kit procedure below to assemble it.
2-battery kit
Step 1: Remove adhesive tapes.
Step 2: Connect all battery terminals by following
below chart.
Step 3: Put assembled battery packs on one
side of plastic shells.
Step 4: Cover the other side of plastic shell as
below chart. Then, battery kit is assembly well.
4-battery kit
Step 1: Remove adhesive tapes.
Step 2: Connect all battery terminals by following
below chart.
Step 3: Put assembled battery packs on one
side of plastic shells.
Step 4: Cover the other side of plastic shell as
below chart. Then, battery kit is assembly well.
Tapes
Tapes
Tapes
________________________________________________________________________________
LA-ITR-LCD
9
6-battery kit
Step 1: Remove adhesive tapes.
Step 2: Connect all battery terminals by following
below chart.
Step 3: Put assembled battery packs on one
side of plastic shells.
Step 4: Cover the other side of plastic shell as
below chart. Then, battery kit is assembly well.
Tapes
Tapes
________________________________________________________________________________
LA-ITR-LCD
10
3. Operations
3.1. Button Operation
Button
Function
ON/MUTE Button
Turn on the UPS: Press and hold ON/Mute button for at least 2
seconds to turn on the UPS.
Mute the alarm: After the UPS is turned on in battery mode, press
and hold this button for at least 5 seconds to disable or enable the
alarm system. But it is not applied to the situations when warnings or
errors occur.
Up key: Press this button to display previous selection in UPS setting
mode.
Switch to UPS self-test mode: Press and hold ON/Mute button for 5
seconds to enter UPS self-testing while in AC mode
OFF/ENTER
Button
Turn off the UPS: Press and hold this button at least 2 seconds to
turn off the UPS
Confirm selection key: Press this button to confirm selection in UPS
setting mode.
SELECT Button
Switch LCD message: Press this button to change the LCD message
for input voltage, input frequency, battery voltage, output voltage and
output frequency.
Setting mode: Press and hold this button for 5 seconds to enter UPS
setting mode when UPS is off.
Down key: Press this button to display next selection in UPS setting
mode.
3.2. LCD Panel
Rack Display Tower Display
Battery info
Load info
Input/output
and Battery
info
UPS status
Warning
& Fault info/
Setting
operation
Backup
time
info
Load info
UPS status
Backup time
info
Input/output
and Battery
info
Warning & Fault info/
Setting operation
Battery info
________________________________________________________________________________
LA-ITR-LCD
11
Display
Function
Backup time information
Indicates the backup time in pie chart.
Indicates the backup time in numbers.
H: hours, M: minute
Warning & Fault information
Indicates that the warning and fault occurs.
Indicates the warning and fault codes, and the codes are
listed in details in 3.5. section.
Setting Operation
Indicates the setting operation.
Input/Output & Battery information
Indicates the output/input voltage, output/input frequency or
battery voltage. V: voltage, Hz: frequency
Indicates the external battery pack numbers.
Load information
Indicates the load level by 0-25%, 26-50%, 51-75%, and
76-100%.
Indicates overload.
Indicates the load or the UPS output is short-circuited.
UPS status
Indicates that programmable management outlets are
working.
Indicates that the UPS alarm is disabled.
Indicates the UPS powers the output directly from the mains
Indicates the battery charger is working.
Indicates the UPS is working in boost mode
Indicates the UPS is working in buck mode
Battery information
Indicates the Battery level by 0-25%, 26-50%, 51-75%, and
76-100%.
Indicates low battery.
Indicates there is something wrong with battery.
3.3. Audible Alarm
Battery Mode
Sounding every 4 seconds
Low Battery
Sounding every second
Overload
Sounding twice every second
Fault
Continuously sounding
________________________________________________________________________________
LA-ITR-LCD
12
3.4. LCD Display Wordings Index
Abbreviation
Display content
Meaning
ENA
Enable
DIS
Disable
ESC
Escape
EP EPO
FA Fan
TP Temperature
CH Charger
RAC
Rack display
TOE
Tower display
SF Site Fault
3.5. UPS Setting
There are two parameters to set up the
UPS.
Parameter 1: It is for program
alternatives. There are 4 programs to
set up: output voltage setting, ,
programmable outlets enable/disable,
programmable outlets setting ,
LCD display direction and exit.
01: Output voltage setting
Interface
Setting
For 208/220/230/240 VAC models, you may choose the
following output voltage:
208: presents output voltage is 208Vac
220: presents output voltage is 220Vac
230: presents output voltage is 230Vac
240: presents output voltage is 240Vac
For 110/120 VAC models, you may choose the following
output voltage:
110: presents output voltage is 110Vac
120: presents output voltage is 120Vac
02: Programmable outlets enable/disable
Interface
Setting
ENA: Programmable outlets enable
DIS: Programmable outlets disable
Parameters 1
Parameters 2
________________________________________________________________________________
LA-ITR-LCD
13
03: Programmable outlets setting
Interface
Setting
Setting the backup time limits in minutes from 0-999 for
programmable outlets that connect to non-critical devices
on battery mode.
04: LCD display direction setting
Interface
Setting
RAC: the LCD display is horizontal.
TOE: the LCD display is vertical.
00: Exit setting
Steps for setting programmable outlet
Step 1:
Before entering setting mode, the UPS should be in Stand-by
mode (off-charging) and make sure the battery is connected. The
LCD display is shown as right.
Step 2:
Press and hold the “Selection” button for 5 seconds to enter
Setting mode.
Step 3:
Press the “Up“ button (ON/MUTE) to switch to "02" of program list.
Then press “Enter“ button to enter value setting of parameter 2.
Press the “Up” button to change the value to “ENA” to enable the
programmable outlet function. Then press “Enter” button again to
confirm the setting.
________________________________________________________________________________
LA-ITR-LCD
14
Step 4:
Press the “Up“ button (ON/MUTE) again to switch to "03" of
program list. Then press “Enter“ button for setting programmable
outlet time. Push “Up” button to change the value of backup time
according your demand. Then press “Enter” to confirm the setting.
Step 5:
Press “Up“ button (ON/MUTE) to switch to "00" of program list. Then press “Enter” button to
exit setting menu.
Step 6:
Disconnect AC input and wait until the LCD display is off. The new setting will be activated
when turning on the UPS again.
3.6. Operating Mode Description
Operating mode
Description
LCD display
ECO mode
When the input voltage is within
voltage-regulated range, UPS will power
the output directly from the mains. ECO is
an abbreviation of Efficiency Corrective
Optimizer. In this mode, when battery is
fully charged, the fan will stop working for
energy saving.
Buck mode
when AC is
normal.
When the input voltage is higher than the
voltage regulation range but lower than
high loss point, the buck AVR will be
activated.
Boost mode
when AC is
normal.
When the input voltage is lower than the
voltage regulation range but higher than
low loss point, the boost AVR will be
activated.
Battery mode
When the input voltage is beyond the
acceptable range or power failure and
alarm is sounding every 4 seconds, UPS
will backup power from battery.
________________________________________________________________________________
LA-ITR-LCD
15
Operating mode
Description
LCD display
Standby mode
UPS is powered off and no output supply
power, but still can charge batteries.
3.7. Faults Reference Code
Fault event
Fault code
Icon
Fault event
Fault code
Icon
Bus start fail
01
x
Inverter output short
14
Bus over
02
x
Battery voltage too high
27
x
Bus under
03
x
Battery voltage too low
28
Inverter soft start fail
11
x
Over temperature
41
x
Inverter voltage high
12
x
Over load
43
Inverter voltage Low
13
x
3.8. Warning Indicator
Warning
Icon (flashing)
Alarm
Low Battery
Sounding every second
Overload
Sounding twice every second
Battery is not connected
Sounding every second
Overcharge
Sounding every second
Site wiring fault
Sounding every second
EPO enable
Sounding every second
Fan Failure
Sounding every second
Over temperature
Sounding every second
Charger failure
Sounding every second
Battery Fault
Sounding every second
________________________________________________________________________________
LA-ITR-LCD
16
4. Troubleshooting
If the UPS system does not operate correctly, please solve the problem by using the table
below.
Symptom
Possible cause
Remedy
No indication and alarm even
though the mains is normal.
The AC input power is not
connected well.
Check if input power cord
firmly connected to the
mains.
The AC input is connected
to the UPS output.
Plug AC input power cord
to AC input correctly.
The icon and the warning
code flashing on LCD
display and alarm is sounding
every second.
EPO function is activated.
Set the circuit in close
position to disable EPO
function.
The icon and flashing
on LCD display and alarm is
sounding every second.
Line and neutral
conductors of UPS input
are reversed.
Rotate mains power
socket by 180° and then
connect to UPS system.
The icon and flashing
on LCD display and alarm is
sounding every second.
The external or internal
battery is incorrectly
connected.
Check if all batteries are
connected well.
Fault code is shown as 27, and
the icon is lighting on LCD
display and alarm is continuously
sounding.
Battery voltage is too high
or the charger is fault.
Contact your dealer.
Fault code is shown as 28, and
the icon is lighting on LCD
display and alarm is continuously
sounding.
Battery voltage is too low
or the charger is fault.
Contact your dealer.
The icon and the icon
are flashing on LCD
display and alarm is sounding
twice every second.
UPS is overload
Remove excess loads
from UPS output.
Fault code is shown as 43, and
the icon is lighting on
LCD display and alarm is
continuously sounding.
The UPS shut down
automatically because of
overload at the UPS
output.
Remove excess loads
from UPS output and
restart it.
Fault code is shown as 14 and
alarm is continuously sounding.
The UPS shut down
automatically because
short circuit occurs on the
UPS output.
Check output wiring and if
connected devices are in
short circuit status.
________________________________________________________________________________
LA-ITR-LCD
17
Symptom
Possible cause
Remedy
Fault code is shown as 1, 2, 3, 4,
11, 12, 13 and 41 on LCD display
and alarm is continuously
sounding.
A UPS internal fault has
occurred.
Contact your dealer
Battery backup time is shorter
than nominal value
Batteries are not fully
charged
Charge the batteries for at
least 5 hours and then
check capacity. If the
problem still persists,
consult your dealer.
Batteries defect
Contact your dealer to
replace the battery.
The icon and the warning
code flashing on LCD
display and alarm is sounding
every second.
Fan is locked or not
working
Check fans and notify
dealer!!
________________________________________________________________________________
LA-ITR-LCD
18
5. Storage and Maintenance
5.1. Operation
The UPS system contains no user-serviceable parts. If the battery service life (3~5 years
at 25°C ambient temperature) has been exceeded, the batteries must be replaced. In this
case, please contact your dealer.
5.2 Storage
Before storing, charge the UPS 5 hours. Store the UPS covered and upright in a cool, dry
location. During storage, recharge the battery in accordance with the following table:
Storage Temperature
Recharge Frequency
Charging Duration
-25°C - 40°C
Every 3 months
1-2 hours
40°C - 45°C
Every 2 months
1-2 hours
Be sure to deliver the spent battery to a recycling facility or ship it to your
dealer in the replacement battery packing material.
________________________________________________________________________________
LA-ITR-LCD
19
MODEL
LA-ITR-800-
LCD
LA-ITR-1100-
LCD
LA-ITR-1500-
LCD
LA-ITR-2000-
LCD
LA-ITR-2500-
LCD
LA-ITR-3000-
LCD
CAPACITY
800 VA /
640 W
1100 VA /
880 W
1500 VA /
1200 W
2000 VA /
1600 W
2500 VA /
2000 W
3000 VA /
2400 W
INPUT
Acceptable Voltage Range
81-145 VAC or 162-290 VAC
Frequency Range
60/50 Hz (auto sensing)
OUTPUT
Voltage Regulation (AC Mode)
110/120 VAC or 208/220/230/240 VAC
Voltage Regulation (Batt. Mode)
±3%(before battery alarm)
Frequency Range (Batt. Mode)
50 Hz or 60 Hz ± 1 Hz
Current Crest Ratio
3:1
Harmonic Distortion
8% max @ 100% linear load, 15% max @ 100% non-linear load (before alarm)
Transfer Time
Typical 2-6 ms, 10ms max.
Waveform (Batt. Mode)
Pure Sine Wave
EFFICIENCY
AC Mode
97%
97%
97%
Buck & Boost Mode
90%
90%
90%
Battery Mode
83%
85%
87%
BATTERY
Standard
Model
Battery Type &
Number
12 V/7 Ah x 2
12 V/9 Ah x 2
12 V/7 Ah x4
12 V/9 Ah x4
12 V/7 Ah x6
12 V/9 Ah x6
Charging Voltage
27.4 VDC ± 1%
54.8 VDC ± 1%
82.1 VDC ± 1%
Recharge Time
4 hours recover to 90% capacity
Long-run
Model
Charging Current
N/A
4 A/8A
N/A
4 A/8A
N/A
4 A/8A
Charging Voltage
27.4 VDC ± 1%
54.8 VDC ± 1%
82.1 VDC ± 1%
PROTECTION
Full Protection
Overload, short, discharge, and overcharge protection
ALARM
Battery Mode
Sounding every 10 seconds
Low Battery
Sounding every second
Overload
Sounding every 0.5 second
Battery Replacement Alarm
Sounding every second
Fault
Continuously sounding
PHYSICAL
Standard
Model
Dimension,
DXWXH (mm)
380 x 438 x 88
480 x 438 x 88
600 x 438 x 88
Net Weight (kg)
12.9
14.23
21.08
23.1
30.65
32.24
Long-run
Model
Dimension,
DXWXH (mm)
N/A
380 x 438 x 88
N/A
480 x 438 x 88
N/A
600 x 438 x
88
Net Weight (kg)
10.8
14
18
ENVIRONMENT
Operating Humidity
0-90 % RH @ 0- 40°C (non-condensing)
Noise Level
Less than 45dB
MANAGEMENT
Smart RS-232/USB
Supports Windows® 2000/2003/XP/Vista/2008, Windows® 7, Linux, Unix, and MAC
Optional SNMP
Power management from SNMP manager and web browser
* Derate capacity to 80% of capacity when the output voltage is adjusted to 208VAC.
**Product specifications are subject to change without further notice.
6. Specifications
Loading...