Lanzar Car Audio VBD300 User Manual

Page 1
OWNER’S MANUAL
VBD 300
PLL SYNTHESIZER STEREO RADIO WITH
COMPACT DISC PLAYER DIGITAL
Page 2
INSTALLATION
Notes:
• Choose the mounting location where the unit will not interfere with the normal driving function of the driver.
• Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
• Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
• Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
• Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
• If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum performance.
30˚
•Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.
DIN FRONT/REAR-MOUNT This unit can be properly installed either from “Front” (conventional DIN Front-mount) or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.
DIN FRONT-MOUNT (Method A)
Installation the unit
1
182
53
(Fig. 1)
2
1. Dashboard
2. Holder
3
3. Screw
2
After inserting the holder into the dashboard, select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place.
Page 3
1
7
4
2
3
6
5
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
6. Strap Be sure to use the strap to secure the back of the unit in place. The strap can
1. Dashboard
(Fig. 2)
be bent by hand to the desired angle.
7. Plain washer
Removing the unit
1. Frame
1
2. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards
2
3
and attach it.)
3. Lever Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the sides of the unit.
1
5
3
2
5
Fastening the unit to the factory radio mounting bracket.
1. Select a position where the screw holes of the bracket and the screw holes of
2
the main unit become aligned (are fitted), and tighten the screws at 2 places on each side.
4
Use either truss screws (5 x 6mm) or flush surface screws (4 x 6mm), depending on the shape of the screw holes in the bracket.
2. Screw
3. Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)
Note: The mounting box, outer trim ring, and half-sleeve are not used for method B installation.
3
Page 4
HOW TO REMOVE AND INSTALL THE FRONT PANEL (OPTIONAL)
1. Press the release button and pull-off the front panel. Keep front panel into the case.
2. To install the front panel, insert the panel into the housing and make sure the panel is properly installed, otherwise, abnormalities occurs on the display or some keys will not function properly.
REMOVING THE FRONT PANEL
Front Panel
Release Button
INSTALLING THE FRONT PANEL
4
Page 5
WIRING CONNECTION FOR 4 X 25W OR 4 X 40W SYSTEM
CD CHANGER
CONNECTOR SOCKET
(FOR CD CHANGER VERSION ONLY)
(BLACK)
(GREEN)
(BROWN)
Rch RED
Lch WHITE
(GREY)
Rch RED
Lch WHITE
FRONT Rch
+
SPEAKER
ANTENNA CONNECTOR
IGNITION SWITCH (B+)
MEMORY BACK-UP
GROUND (B–)
POWER ANTENNA
FRONT Lch
SPEAKER
RED
YELLOW
BLACK
+ –
CHOKE
BOX
BLUE
WHITE
WHITE/BLACK
MAIN UNIT
CD INPUT CABLE
(FOR CD INPUT VERSION ONLY)
SUBWOOFER CABLE
(FOR SUBWOOFER VERSION ONLY)
FRONT RCA CABLE
REAR RCA CABLE
(FOR RCA LINE OUT VERSION ONLY)
GREY
GREY/BLACK
REAR Lch SPEAKER
+ –
GREEN
GREEN/BLACK
VIOLET
VIOLET/BLACK
+
REAR Rch SPEAKER
WIRING CONNECTION FOR 4 X 7W OR 2 X 25W SYSTEM
CD CHANGER
CONNECTOR SOCKET
(FOR CD CHANGER VERSION ONLY)
(BLACK)
(GREEN)
(BROWN)
Rch RED
Lch WHITE
(GREY)
Rch RED
Lch WHITE
2-SPEAKERS SYSTEM
FRONT Rch SPK.
REAR Rch SPK.
GREY
VIOLET/BLACK
ANTENNA CONNECTOR
IGNITION SWITCH (B+)
MEMORY BACK-UP
GROUND (B–)
POWER ANTENNA
2-SPEAKERS SYSTEM
Lch
SPK.
RED
YELLOW
BLACK
WHITE
GREEN/BLACK
MAIN UNIT
CHOKE BOX
BLUE
4-SPEAKERS SYSTEM
FRONT
Lch SPK.
REAR
Lch SPK.
WHITE/BLACK
GREEN/BLACK
WHITE
GREEN
CD INPUT CABLE
(FOR CD INPUT VERSION ONLY)
SUBWOOFER CABLE
(FOR SUBWOOFER VERSION ONLY)
FRONT RCA CABLE
REAR RCA CABLE
(FOR RCA LINE OUT VERSION ONLY)
4-SPEAKERS SYSTEM
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
Rch SPK.
Note:
1. For 2-speakers system, green, violet, white/black and grey/black wire leads are unconnected and isolated.
2. For 2-speakers system, keep the fader indicator at center position to maintain the existing volume level.
Page 6
LOCATION AND FUNCTION OF CONTROLS
824 29
26
171011
1315
20
21 22
16 12
181914
46 3 7
25
5
23
1
27
Press POWER button (1) to turn on. Press it again to turn it off. If the power is off, press BND button (11) or MOD button (12) also can turn on the unit.
Gently insert a compact disc with the label side facing up into the disc slot (2). The disc is then automatically loaded into the unit and starts playing with the first track of the disc. The digital display will indicate the track number.
Press the MUT button (3) to silence the receiver. Press again to resume listening.
(1) ON/OFF
(2) DISC PLAY
(3) MUTE
6
Page 7
Press MON button (4) to select monaural or stereo (Mono reception for radio stations).
(4) MONO/STEREO (FOR MON VERSION ONLY)
You can sometimes improve reception of distant stations by selecting mono operation.
Press X-BAS button (4) to toggle sub-woofer output, when sub-woofer on, display
(4) SUB-WOOFER (FOR SUB.W. VERSION ONLY)
will show “ SW”.
(5) LOUDNESS
Press LOU button (5) to increase bass output and display will show “LOUD”.
(6) SET THE CLOCK
Press and hold the DSP button (6), then press the +/ (15) to change minutes or /– (14) to change hours.
(7) EJECT
Push a CD into slot. The CD will begin to play. Press (eject) button (7) to stop CD play and eject CD from slot. Receiver switches to radio operation.
(8, 9 & 10) SELECT MODE
Press SEL button (8) to move display through bass, treble, balance, fader and volume functions. Use (9) and (10) buttons to adjust the selected mode. When mode has not been adjusted for several seconds, display returns to normal radio or CD display.
BAS TRE BAL FAD VOL
(Bass) (Treble) (Balance) (Fader) (Volume)
Bass Press SEL button (8) for one time. Adjust bass level using (9) and (10) buttons.
Treble Press SEL button (8) for two times. Adjust treble level using (9) and (10) buttons.
Balance
Press SEL button (8) for three times. Adjust sound balance between left and right speakers using (9) and (10) buttons.
Fader
Press SEL button (8) for four times. Adjust sound balance between front and rear speakers using (9) and (10) buttons.
Volume
Press SEL button (8) for five times. Adjust volume level using (9) and (10) buttons.
Press BND button (11) to change between three FM bands and two AM bands and
(11) BAND
one LW band. Each band stores up to six preset stations.
FM1 FM2 FM3 AM1/MW AM2/LW
(12) SELECT LISTENING MODE
Press MOD button (12) to choose desired listening mode. (e.g. radio mode to CD mode to CDC mode). [(e.g. radio mode to CD mode to to AUX (Line)]
7
Page 8
The LCD (13) can show the current state of the unit.
(13) LIQUID CRYSTAL DISPLAY
Press and release a TUNE/SEEK/TRACK button /– (14) or +/ (15) immediately
(14 & 15) SELECT STATIONS
to move radio frequency number up or down on step. Press and hold a TUNE/SEEK/TRACK button /– (14) or +/ (15) for several seconds to seek the next clear station.
(14 & 15) SKIP TRACKS
Press a TUNE/SEEK/TRACK button /– (14) or +/ (15) to move to the previous track or the following track. Track number shows on the display.
(14 & 15) FAST FORWARD AND FAST REVERSE
Press a TUNE/SEEK/TRACK button /– (14) or +/ (15) to fast reverse or fast forward. CD play starts from when you release the button.
(16) PRESET STATIONS
Six number buttons (16) store and recall stations for each band. Store a station: Select a band (11) (if needed). Select a station. Hold a preset button for several seconds. Recall a station: Select a band (11) (if needed). Press a preset button to select stored station.
(17) TOP: PLAY THE FIRST TRACK
Press TOP button (17) to play the first track of the current disc.
(18) REPEAT THE SAME TRACK
During CD mode, press RPT button (18) to continuously repeat the same track. Press again to stop repeat. During CDC mode, press RPT button (18) to continuously repeat the same track, press it again to continuously repeat all tracks on the current disc and press it at the third time to stop repeat.
During CD mode, press SCN button (19) to play first several seconds of each track
(19) INTRO: PREVIEW ALL TRACKS
on the current disc. Press again to stop intro and listen to track. During CDC mode, press SCN button (19) to play first several seconds of each track on the current disc. Press it again to play first several seconds of each track on all discs in the CD magazine. Press it at the third time to stop intro and listen to track.
(20) RANDOM: PLAY ALL TRACKS
During CD mode, press RND button (20) to play all tracks on CD in random. Press again to cancel the function. During CDC mode, press RND button (20) to play all tracks on the current disc. Press it again to play all tracks on all discs in the CD magazine. Press it at the third time to cancel the function.
(21 & 22) SELECT DISC (FOR CD CHANGER VERSION ONLY)
During CDC mode, press D.DN button (21) to select previous disc and D.UP button (22) to select next disc.
ATTENTION: DURING CDC MODE, TURN OFF THE UNIT AND CHANGE THE DISC IN THE CD MAGAZINE, THEN TURN IT ON. IF THE UNIT CAN’T WORK WELL, PLEASE PRESS D.DN BUTTON (21) OR D.UP BUTTON (22) FOR ONE TIME.
8
Page 9
(23) AUTOMATICALLY STORING & PROGRAM SCANNING
Automatically Storing
Press and hold AMS button (23) for several seconds to toggle automatically storing function. It starts searching next frequency in local mode and stores the clear station into the preset memory. If 6 ch. is not fully memorised, it would start the second searching in distance mode. At the end of automatically storing operation, mode is changed to Preset Scan.
Preset Scanning
Press AMS button (23) shortly to toggle preset scanning function. During the scanning, it will stop at every stored station for several seconds and the number of the channel being scanned flashes on the display. Press it again to stop scanning.
Press RELEASE button (24) to detach the removable faceplate.
(24) FACEPLATE RELEASE
(25) EQUALIZATION
Press EQ button (25) to turn on equalization function and to select desired audio mode. There are four kinds of mode as below:
FLAT ROCK CLASSIC POP
(26) REMOTE SENSOR (OPTIONAL)
Point the remote handset to control the remote sensor (26). Press the function keys on the remote handset to control the system.
(27) RESET BUTTON FUNCTION
RESET button (27) is placed on the housing and must be activated with either a ball
point pen or thin metal object. The reset button is to be activated for the following reasons:
• Initial installation of the unit when all wiring is completed.
• All the function buttons do not operate.
• Error symbol on the display.
Note: If press RESET button (27), the unit can’t work yet, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel.
9
Page 10
Remote Control Handset
13
15
213 4 5
Control & Function Keys
1. POWER = Power ON/OFF Button
2. MOD = Mode Button
3. SEL = Select Button
4. EQ = Equalization Button
5. BND = Band Select Button
6. MUTE = Mute Button
9
8
6
7
10
14
1112
7. VOL + = Volume Up Button
8. VOL – = Volume Down Button
9. TUN/SEK = Tune/Seek Up Button
10. TUN/SEK = Tune/Seek Down Button
11. PRESET = Preset Button
12. TOP = Top Button
13. SCN = Scanning Button
14. RPT = Repeat Button
15. RND = Random Button
10
Page 11
SPECIFICATION
GENERAL
Power Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 155 (D) x 50 (H) Tone Controls
- Bass (at 100 Hz) : +10 dB / –10 dB
-Treble (at 10 KHz) : +10 dB / –10 dB
Maximum Output Power
- Version v : 7W x 4 (ch) or 25W x 2 (ch)
- Version z : 25W x 4 (ch)
- Version y : 40W x 4 (ch)
CD PLAYER
Signal to Noise Ratio : More than 60 dB Channel Separation : More than 60 dB Frequency Response : 20 Hz - 20 KHz
RADIO
For 3 Bands For 2 Bands For 2 Bands (Europe) (Europe) (U.S.A.)
Frequency Coverage : 87.5 to 108 MHz 87.5 to 108 MHz 87.5 to 107.9 MHz IF : 10.7 MHz 10.7 MHz 10.7 MHz
Sensitivity (S/N = 30 dB) : 3 µV3 µV3 µV
Stereo Separation : > 30 dB > 30 dB > 30 dB
FM FM FM
Frequency Coverage : 522 to 1620 KHz 522 to 1620 KHz 530 to 1710 KHz IF : 450 KHz 450 KHz 450 KHz Sensitivity (S/N = 20 dB) : 32 dBu 32 dBu 32 dBu
Frequency Coverage : 144 to 290 KHz IF : 450 KHz Sensitivity (S/N = 20 dB) : 35 dBu
MW MW AM
LW
11
Page 12
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer.
Symptom Cause Solution
No power. The car ignition is not on. If the power supply is properly
The fuse is blown. Replace the fuse.
Disc cannot Presence of CD disc Remove the disc in the player, then be loaded or inside the player. put a new one. ejected.
Inserting the disc in Insert the compact disc with the reverse direction. label facing upward.
Compact disc is extremely Clean the disc or try to play a new dirty or defective disc. one.
Temperature inside the Cool off or until the ambient car is too high. temperature return to normal.
Condensation. Leave the player to off for an hour
No sound. Volume is in minimum. Adjust volume to a desired level.
Wiring is not properly Check wiring connection. connected.
The operation The built-in microcomputer Press the RESET button. keys do not is not operating properly Front panel is not properly fixed into work. due to noise. its place.
Sound skips. The installation angle is Adjust the installation angle to less
not more than 30 degrees. than 30 degrees.
connected to the car accessory terminal, switch the ignition key to “ACC”.
or so, then try again.
The disc is extremely dirty Clean the compact disc. Then try to or defective disc. play a new one.
The radio does The antenna cable is not Insert the antenna cable firmly. not work. The connected. radio station automatic The signals are too weak. Select a station manually. selection does not work.
www.lanzar.com
88-C0851-27
Loading...