Lanzar VBD1600MP Owners Manual
OWNER’S MANUAL
VBD 1600MP
PLL SYNTHESIZER STEREO RADIO WITH
COMPACT DISC PLAYER DIGITAL
INSTALLATION
Notes:
• Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
• Before finally installing the unit, connect the wiring temporarily and make sure it is
all connected up properly and the unit and the system work properly.
• Use only the parts included with the unit to ensure proper installation. The use of
unauthorized parts can cause malfunctions.
• Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
• Install the unit where it does not get in the driver’s way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
• If installation angle exceeds 30˚ from horizontal, the unit might not give its optimum
performance.
30˚
• Avoid installing the unit where it would be subject to high temperature, such as from
direct sunlight, or from hot air, from the heater, or where it would be subject to dust,
dirt or excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from “Front” (conventional DIN Front-mount)
or “Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of
the unit chassis). For details, refer to the following illustrated installation methods.
DIN FRONT-MOUNT (Method A)
Installation the unit
1
182
53
(Fig. 1)
2
1. Dashboard
2. Holder
3
3. Screw
2
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
1
7
4
2
3
6
5
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap can
(Fig. 2)
be bent by hand to the desired angle.
7. Plain washer
Removing the unit
1. Frame
2
1
2. Release Frame Key
Insert the release ring key into the
groove at the right side of the frame,
then pull out to remove the frame at a
little angle from horizontal.
(You can also use the key to remove the
frame from the left side)
3
3. Release Unit Key
After release the frame, insert the levers
supplied with the accessory into the
grooves at both sides of the unit as
shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the sides of the unit.
1
5
3
2
5
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw holes
of the bracket and the screw holes of
2
the main unit become aligned (are fitted),
and tighten the screws at 2 places on
each side.
4
Use either truss screws (5 x 5mm) or
flush surface screws (4 x 5mm),
depending on the shape of the screw
holes in the bracket.
2. Screw
3. Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method B
installation.
3
WIRING CONNECTION
ANTENNA CONNECTOR
IGNITION
SWITCH (B+)
MEMORY
BACK-UP
GROUND (B–)
ANTENNA
POWER
RED
YELLOW
BLACK
CHOKE
BOX
BLUE
MAIN UNIT
SUBWOOFER CABLE
FRONT RCA CABLE
REAR RCA CABLE
(GREEN)
(BROWN)
(GREY)
Rch RED
Lch WHITE
Rch RED
Lch WHITE
FRONT Lch
SPEAKER
REAR Lch
SPEAKER
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
FRONT Rch
SPEAKER
REAR Rch
SPEAKER
4
Loading...