Lanzar VBD1500MP Owners Manual
VBD 1500MP
OWNER’S MANUAL
Mobile Audio System
• PLL Synthesizer Stereo Radio
• Digital Compact Disc Player
• Automatically Memory Storing
• Preset Equalization
•MP3
• Remote Control
• Slide Down Electronic Detachable Panel
CONTENTS
Installation .....................................................................................................3
DIN Front-Mount (Method A) ..................................................................................3
Installing the unit ...............................................................................................3
Removing the unit .............................................................................................4
DIN Rear-Mount (Method B)...................................................................................4
Using the Detachable Front Panel ..............................................................5
Wiring Connection ........................................................................................6
Operation .......................................................................................................7
General Operation ..................................................................................................7
Radio Operation......................................................................................................9
CD Operation........................................................................................................10
MP3 Operation......................................................................................................11
Remote Control Handset ......................................................................................12
Specification................................................................................................13
Trouble Shooting.........................................................................................14
2
INSTALLATION
Notes:
• Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
• Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.
• Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.
• If installation angle exceeds 30˚ from
horizontal, the unit might not give its
optimum performance.
DIN FRONT-MOUNT (Method A)
Installing the unit
1
182
53
(Fig. 1)
1. Dashboard
2. Holder
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
3. Screw
1
2
3
6
30˚
• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front” (conventional DIN Frontmount) or “Rear” (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
2
3
7
4
(Fig. 2)
5
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap
can be bent by hand to the desired
angle.
7. Plain washer
3
INSTALLATION
Removing the unit
1
(Open/Close)
2
3
4
1. Before removing the frame, press the
(OPEN/CLOSE) button to slide
down the front panel.
2. Frame
3. Insert fingers into the groove in the
right side of the frame and pull out to
remove the frame. (You can also
remove the frame from the left side.)
4. Lever
After removing the frame, press the
(OPEN/CLOSE) button again to
slide up the front panel. Then insert
the levers supplied with the unit into
the grooves at both sides of the unit
as shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the
sides of the unit.
1
2
4
2
3
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw
holes of the bracket and the screw
holes of the main unit become aligned
(are fitted), and tighten the screws at
2 places on each side.
Use either truss screws (5 x 5mm),
depending on the shape of the screw
holes in the bracket.
2. Screw
3. Factory radio mounting bracket
4. Dashboard or Console
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method
B installation.
4
USING THE DETACHABLE FRONT PANEL
To Detach the Front Panel
1. Press the (OPEN/CLOSE) button,
the front panel will slide down.
(Open/Close)
2. Press the (OPEN/CLOSE) button
again, the front panel will slide up.
(Open/Close)
3. When the front panel slides down,
press the bottom button of the front
panel upward and pull it out from the
panel bracket.
To Reinstall the Front Panel
1. When the panel bracket is in slide
down position, insert the front panel
into panel bracket and press
(OPEN/CLOSE) button to slide up.
Bottom
Button
2. When the panel bracket is in slide up
position, insert a side of the front
panel to its proper position and push
another side into the panel bracket, a
‘click’ sound should be heard.
Front Panel
Bottom
Button
4. For safekeeping, store the front panel
in the supplied protective case
immediately after being removed.
Protective Case
Front Panel
3. Note that if the front panel fails to lock
in position properly, press control
button may not function and LCD
display may be missing some
segments. Press the
(OPEN/CLOSE) button and then
reinstall the front panel again.
5
Loading...