CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated dangerous voltagewithin the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral triangle is intended to alert user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
SHOCK, DO NOT EXPOSE
MOISTURE.
CLASS 1 LASER PRODUCT
Laser product symbol: located on the rear panel of the unit, indicate this player is a class
laser product, only use weak laser and no hazardous radiation outside of the unit.
1.Read through this instruction manual before installation and use.
2.Before removing the unit, remove the disc from the unit first.
3.Do not open the cover or touch any of the components exposed out of the unit, only for
qualified technicians.
4.Do not expose the unit to direct sunlight or nearby objects that radiate heat to avoid
damage the unit.
5.Do not place the unit in moist and humid conditions.
6.Please ensure the ventilation holes are not covered to avoid overheating and
malfunction.
7.Clear the panel and case with soft dry cloth only, do not apply any kind of thinner,alcohol
or sprays.
1
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
Contents
1. Before Operation...........................................................................................3
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
1. Before Operation
1.1Glossary
PBC (playback control)
It is a kind of signal(menu) recorded in the disc with SVCD or VCD2.0 format used for the
playback control. For the discs containing PBC, It can playback interactive software with the
menu displayed on monitor screen.
If the disc contain still images, it can playback high definition of still images.
Title
Generally, the title is the important part of DVD disc. for example, the theme part of movie is
title 1, the part described how to make movie is title 2, the cast is title 3, etc. Every title contain
a serial number that is easy to look up.
Chapter
A title can be divided into several blocks, so that every block can be operated as a unit, the
unit is called chapter. The chapter contain a unit at least.
Track
It is the biggest component of VCD. Generally, every song of karaoke disc is a track.
1.2Precautions
Safety
1. Power Source: The unit should be connected to power supply only of the type described
in the operating instructions or as marked on the unit.
2. The unit is designed for negative terminal of the battery which is connected to the
vehicle metal. Please confirm it before installation.
3. Do not allow the speaker wires to be shorted together when the unit is switched on.
Otherwise it may overload or burn out the power amplifier.
4. Do not install the detachable panel before connecting the wire.
Environment
1. Do not use this unit near water and moisture.
2. If moisture forms inside the Lens, it may not operate properly. To correct this problem,
wait until the moisture is evaporated.
3. If the car interior is extremely hot, do not use the player until the car has been cool off .
3
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
1.3Maintenance and Cleaning of Discs
A
B
+ side up
Disc Maintenance
1. To keep the disc clean, handle the disc by its edge, do not touch the disc surface of the
play side.
2. Do not stick paper or tape on the disc. If there is anything on the disc surface, wipe it up
with a soft cloth before using.
3. Do not expose the disc to direct sunlight, or nearby heat sources such as caliduct, or leave
it in a car parked in direct sunlight where there can be a considerable rise in temperature.
4. Put the disc inside disc case to keep temperature after finishing playback.
Disc Cleaning
1. Before playing, wipe the disc with a clean cloth.wipe the disc outwards from the disc
center.
2. Do not use petrol, thinner. Commercial cleaner or anti-static spray to wipe disc.
Fig.1
Fig.2
Fig.3
1.4Battery Information of the Remote Control
Replace Battery in the Remote Control:
1.Before using the remote control for the first time, pull the insulating sheet out of the remote
control as the direction indicated by the arrow.(see fig.1)
2.Press the movable block hold as the direction indicated by the A arrow(See fig.2), then pull
the battery holder out of the remote control as the direction indicated by the B arrow(see
fig.2).
3.Replace the old battery by a new battery with (+) polarity side upward(See fig.3).
4.Insert the battery holder to the original position in remote control.(See fig.3).
Note about the Battery of the Remote Control:
1.Lithium battery: CR 2025 3V.
2.Battery Life: 6 months with normal use in normal room temperature.
3.Improper use of battery may cause overheating or explosion, so that Result in injury or fire .
4.Battery leakage may cause damage to the remote control.
5.Do not short the battery.
6.Do not throw the battery into the fire.
7.To avoid the risk of accident, keep the battery out of reach of children.
4
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
1.5 The Remote Control Description
23456
7981011
12
1516171819
20
272829303132333435
SLOW_FWD
ZOOM
ST
MODE
SUBTITLE
TITLE/PBC
RPT
RDM
SEARCH
APS
P/N
0/10
3
4
0K
MENU
PROG
LOUD
STEP
393637
38
1
PWROPEN
EQ
SETUP
INT
AUDIO
OSD
BAND
1. TILT BUTTON
2. MENU BUTTON
3. POWER BUTTON
4. ^ BUTTON
5. >>| BUTTON
2
7
8
10+
6. > BUTTON
7.|<< BUTTON
8. v BUTTON
9. SEL BUTTON
10. PLAY/PAUSE BUTTON
11.NUMBER(0~10,+10
12. 10+ BUTTON
13. SETUP BUTTON
14. MODE BUTTON
15. APS BUTTON
28. LOC/SLOW-FWD BUTTON
29. MUTE BUTTON
30. STOP BUTTON
31. VOLUME- BUTTON
32. < BUTTON
33. OK BUTTON
34. VOLUME+ BUTTON
35. BAND AND P/N BUTTON
36. PROG BUTTON
37. OSD BUTTON
38. LOUD BUTTON
39. STEP BUTTON
14
MU
SEL
+
13
-101+10
596
24
21
22
26
25
23
CLK
LOC
A-B
16. SEARCH BUTTON
17. RDM BUTTON
18. RPT BUTTON
19. SUBTITLE BUTTON
20. TITLE/PBC BUTTON
21. ST BUTTON
22. ZOOM BUTTON
23. AUDIO BUTTON
24. CLK BUTTON
25. A-B BUTTON
26. INT BUTTON
27. EQ/OPEN BUTTON
-10) BUTTONS
5
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
1.6The Locations and Names of Controls on or in the unit
The Front Facet after removing the front panel
21
SD/MMC
3 4 6
141617
151920
24
The Front Panel
8
2
MODE
MUTE
23
1
OPEN
18
BAND
APS
10
11
9
1
12
5
22
INT
23
13
AV IN
RPT
45
-10RDM
+10
6
USB
REL
1. OPEN button
2. POWER/MUTE button
3. Monitor
4. AV IN socket
5. Disc Slot
6. USB Jack
7. SD/MMC Card Slot
8. MODE button
9. VOL knob
10. >>| button
11. |<< button
12. PLAY/PAUSE/1 button
7
13. INT/2 button
14. RPT/3 button
15. RDM/4 button
16. - 10 / 5 button
17. + 10 / 6 button
18. BAND button
19. APS button
20. EJECT button
21. RESET button
22. Small LCD Screen
23. IR Remote Sensor
24. REL button
6
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
1.7Wires Connection Description
Wiring Connecting Socket 1
WIRING CONNECTING SOCKET 1
WIRING CONNECTING SOCKET 2
The Description of the Wires Connection
Fixing Screw Bolt
Wiring Connecting Socket 2
Black
Radio Antenna jack
Black
1. Parking wire must be connected. And the parking brake must be engaged in order for the
monitor to work.
2. Use the clip end of the Ground Wire provided by manufacturer to connect Mounting Screw,
using the other end of the Ground Wire to connect the negative pole of the power source.
Otherwise, the video on screen maybe flashes.
The Description of the Wiring Diagram for Socket 1
WIRING CONNECTING PLUG 1
NOTES:
1. Only speakers with 4 ohms impedance may be used.
2. Ensure that the blue auto antenna cable does not make contact with any ground
connection.
The Description of the Wiring Diagram for Socket 2
WIRING CONNECTING PLUG 2
REAR VIEW CAMERA
7
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
Description of Connecting the Parking Brake Line to the Parking Brake System Built in the Car
Parking brake
NOTE: after connecting the Parking Line, the video on the small monitor of the front panel will be display only after braking the car.
Ground(-)/Park Break(Coffee)
Parking brake switch
(inside the car)
1.8UNIT INSTALLATION
INSTALLATION INSTRUCTIONS
THE UNIT IS INSTALLED TO BE AN ANTI-THEFT ONE. THE CHASSIS
OF THE UNIT WEARS A SLIDING METAL HOUSING. PLEASE DO THE
CONNECTION OF THE POWER, SPEAKERS AND ANTENNA ACCORDING
TO THE REQUIREMENT OF THE INSTRUCTION BOOK , THEN INSTALL
THE SLIDING METAL HOUSING IN THE CAR AS FOLLOWS.
TO BOOST UP THE CAPABILITY OF
ANTI-JAMMING, PLEASE FIX THE
METAL STRAP ON THE METAL
CONNECTED TO THE BOTTOM
METAL STRAP
DASH BOARD
SLIDING METAL HOUSING
BRACKET OF THE CAR.
To metallic body or chassis of the car
UNIT CHASSIS
SELECT THE PROPER TAB
FOR FIXING THE SLIDING
METAL HOUSING.
PLASTIC TRIM OUT
FRONT PANEL
TO DRAW THE CHASSIS OUT OF
THE SLIDING METAL HOUSING,
INSERT THE LEFT AND RIGHT KEY
PLATES INTO THE RIGHT POSITION
OF THE 2 SIDES OF CHASSIS.
8
PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.