Bluetooth Headset User Manual Model:BH08 FCC ID:ZG8BH08
1. Introduction :
The Bluetooth headset BH08U allows you the freedom to make and receive calls
while on the move or in the office, after you connect the headset to a compatible
phone that supports Bluetooth wireless technology.
Read this user guide carefully before using the headset. Read also the user guide for
your phone, which provides important safety and maintenance information.
2. Specification:
* Bluetooth Specification v2.1+EDR
* Supports connecting to two phones simultaneously
* Supports Bluetooth Headset and Hands-free Profile (HFP 1.5)
3. Bluetooth wireless technology:
Bluetooth wireless technology makes it possible to connect compatible
communication devices without using cables. A Bluetooth connection does not require
that the phone and the headset be in line of sight, but both devices should be within 10
meters (30feet) of each other. Connections can be subject to interference from
obstructions, such as walls or other electronic devices.
BH08U is compliant with Bluetooth Specification v2.1 supporting Headset profiles
1.1 and Hands-Free Profiles 1.5.
There may be restrictions on using Bluetooth technology in some locations .Check
with your local authorities or service provider.
4. Overview:
The headset contains the following parts as shown in the figure:
(1)Answer/end key.
(2)Led Indicator (red/blue)
(3)Microphone
(4)Volume up and volume down buttons
(5)Ear piece
(6)Charger socket
(7) Ear Hook
Before you start using the headset, you must charge the battery and pair the headset
with a compatible phone.
5. Charging the headset:
This device has an internal, rechargeable battery which must be fully charged before
used for the first time. It takes you about 3 hours to charge the battery full for the first
time. During charging, the indicator shows a steady red. When the battery is fully
charged, the Red light will turn blue . For the later on charging, it takes about 2 hours.
You can charge the headset by using the car charger included in the package.
The fully charged battery has power for up to 6 hours of talking time or up to 120
hours of standby time. However, the talk and standby times may vary when used with
different mobile phones, products that use a Bluetooth connection, usage settings,
usage styles, and environments.
When the battery is running out of power, the Red indicator light starts to flash 1
times every 15 seconds with beep voice . This indicates that the headset needs to be
charged as soon as possible.
6. Switch ON or OFF the headset:
To switch on, when BH08U is in off state, press and hold the answer/end key for 3
seconds until the Blue indicator light starts to flash for 3 times
To switch off, when BH08U is in on state, press and hold the answer/end key for
3seconds until the Red indicator light flashes for 3 times.
7. Pair the headset with a compatible phone:
Pairing is the process of establishing encrypted link between BH08U and Bluetooth
devices.
Step-1 The headset must be powered off before you begin to initiate the paring.
Step-2 press and hold the answer/end key for 6 second until the Blue and Red light
flash alternatively. The headset is now in paring mode.
Step-3 Activate the Bluetooth feature on the phone, and set the phone to search for
Bluetooth devices. Check the user guide of your phone for instructions.
Step-4 Select the headset (BH08U ) from the list of found devices.
Step-5 When asked the PIN code, please enter “0000” to pair and connect the headset
to your phone. In some phones you may need to make the connection separately after
pairing. See the user guide of your phone for details.
If the pairing is successfull, the headset enters idle state and Blue light will flash
flashes 1 time every 3 seconds. The headset’s name appears in the phone menu where
you can view the currently paired Bluetooth devices.
You only need to pair the headset with your phone once.
Note for Multipoint use: In order to pair a second mobile, please press the volume button for 6 seconds until the Red and Blue light flashes alternatively, headset is ready
into pairing mode and you can pair the second mobile. Turn off the headset and
re-turn on it, both mobile was ready under links.
To activate the Multipoint-function, please press volume -/+ at the same time for 3
seconds, headset will get into the multipoint Mode, the Blue LED indicate 2 seconds.
Troubleshooting:
If you cannot connect the headset to your phone, do as follows:
- Ensure that the headset is charged, switched on, paired with and connected
to your phone.
- Ensure that the Bluetooth feature is activated on your phone.
- Check that the headset is within 10 meter (30 feet) of your phone and that there are
no obstructions between the headset and the phone, such as walls or other electronic
devices.
- If no paring is made over a period of time, the headset will retreat paring mode. You
have to turn off the headset and operate again.
8. Basic use:
Make a call:
To make a call, use your phone in the normal way when the headset is connected to
your phone. The sound will be transmitted to the headset automatically.
Answer a call:
When there is incoming call, press the answer/end key, or use the phone keys to
answer the call.
End a call.
After finishing the call, press the answer/end key, or use the phone keys to end the
call.
Refuse a call:
When there is incoming call, press and hold answer/end button for 3 seconds until you
can hear beep sound from the headset.
Voice dialing (dialing a number by saying a name):
It is possible to make a call directly from the headset using voice recognition. To use
this voice dialing function, your mobile phone must provide this option and
corresponding voice samples must have been recorded.
Step-1 Enable voice recognition function of your mobile and set the mobile to
handsfree state. (pls make sure the mobile phone can support this function )
Step-2 Quickly Press the answer/end button in standby mode , Speak out the name
of the person you wish to call loudly.
Redial last number :
Press Voice + key 3 seconds & the headset will dial the last dialed telephone
number.
Adjust the earphone volume:
Press the volume + key to increase or - to decrease the volume during a call.
Switch the call between mobile and headset:
In call state, press and hold the answer/end key for about 3 seconds until there is beep
sound from headset. The call will be switched from headset to mobile .the same
operation can switch the voice from mobile to headset .
Note for Multipoint use: When the first phone (AG1) under making a call, another
calling into from the second phone which is also connected with the Bluetooth
headset, press volume+ about 1.5 seconds will answer the call in from the second
phone (AG2), and will hold for the AG1’s calling. press volume + 1.5 seconds will
switch the calling between two phones. Short press the power key will end the call of
talking, meantime will connect to the hold phone. (some phone will asking if you
want to connect the phone or not), press again the power key will ending the call of
talking.
Mute&Unmute :
Quickly press Voice + &Voice – at the same time will on or off the mute function .
when the mute function is on ,you will hear two short beeps every 10 secconds .
9. LED Indication:
Headset status LED Indication
In standby mode BlueLED flashes 1 times every 3 seconds
In coming call Blue LED flashes twice every 2 seconds
Low battery Red LED flashes 1 times every 15
seconds and there is beep sound
On telephone conversion BlueLED flashes 1 times every 1 seconds
On charger Red LED is on
Charge complete Blue LED is on
10. Battery information:
Your device is powered by a rechargeable battery. The full performance of a new
battery is achieved only after two or three complete charge and discharge cycles. The
battery can be charged and discharged hundreds of times, but it will eventually wear
out.
Unplug the charger from the electrical plug and the device when not in use. Do not
leave a fully charged battery connected to a charger, since overcharging may shorten
its lifetime. If left unused, a fully charged battery will lose its charge over time.
Leaving the device in hot or cold places, such as in a closed car in summer or winter
conditions, will reduce the capacity and lifetime of the battery. Always try to keep the
battery between 15℃ and 25℃(59℉ and 77℉). A device with a hot or cold battery
may not work temporarily, even when the battery is fully charged. Battery
performance is particularly limited in temperatures well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may also explode
if damaged. Dispose of batteries according to local regulations. Please recycle when
possible. Do not dispose as household waste.
11. Care and maintenance:
Your device is a product of superior design and craftsmanship and should be treated
with care. The suggestions below will help you protect your warranty coverage.
· Keep all accessories and enhancements out of the reach of small children.
· Keep the device dry. Precipitation, humidity, and all types of liquids or moisture
can contain minerals that will corrode electronic circuits. If your device does get wet,
allow it to dry completely.
· Do not use or store the device in dusty, dirty areas. Its moving parts and electronic
components can be damaged.
· Do not store the device in hot areas. High temperatures can shorten the life of
electronic devices, damage batteries, and warp or melt certain plastics.
· Do not store the device in cold areas. When the device returns to its normal
temperature, moisture can form inside the device and damage electronic circuit
boards.
· Do not drop, knock, or shake the device. Rough handling can break internal circuit
boards and fine mechanics.
· Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the
device.
· Do not paint the device. Paint can clog the moving parts and prevent proper
operation.
All of the above suggestions apply equally to your device, battery, charger, or any
enhancement. If any device is not working properly, take it to the nearest authorized
service facility.
MPORTANT REGULATORY INFORMATION
This device complies with Part 15 of the FCC Rules: Operation is subject to the following two
conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference that is received, including any interference that
may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Loading...