Lantech IPES-0008A-12V, IPES-0208CA-12V User Manual

Lantech

IPES-0008A-12V

8 10/100TX w/ 8 Booster PoE at/af

Injector Industrial Switch

User Manual

V1.00

Jun 2010

Recommendation for Shielded network cables

STP cables have additional shielding material that is used to reduce external interference. The
shield also reduces the emission at any point in the path of the cable. Our recommendation is
to deploy an STP network cable in demanding electrical environments. Examples of
demanding indoor environments are where the network cable is located in parallel with
electrical mains supply cables or where large inductive loads such as motors or contactors are
in close vicinity to the camera or its cable. It is also mandatory to use an STP cable where the
power device (like IP camera) is used outdoors or where the network cable is routed outdoors.

FCC Warning

This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class-A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Content

Introduction .............................................................. 1

Features ................................................................. 1

Technical Specification ........................................... 2

Package Contents ................................................. 4

Safety Precaution .................................................. 4

Hardware Description .............................................. 5

Physical Dimension................................................ 5

Front Panel ............................................................ 6

Top View ................................................................ 6

LED Indicators ....................................................... 7

Ports ....................................................................... 8

Cabling ................................................................... 9

Wiring the Power Inputs ......................................10

Wiring the Fault Alarm Contact ...........................12

Mounting Installation ..............................................13

DIN-Rail Mounting ................................................13

Wall Mounting .......................................................15

Hardware Installation ..............................................16

Installation Steps ..................................................16

Network Application................................................17

Troubleshooting ......................................................18

1

Introduction

IPES-0008A-12V Industrial Switch is a cost-effective solution, which meets the high
reliability requirements demanded by industrial applications, and also supports to
operate in the wide temperature -40°C ~ 75°C environments. Besides, the equipment
supports 12V or 48V DC power input and provides the PoE function with 48VDC
output for kinds of Powered Devices to receive power as well as data over an RJ-45
cable.

Features

 System Interface/Performance

 RJ-45 ports support Auto MDI/MDI-X Function
 Embedded 4-port PoE Injection
 Store-and-Forward Switching Architecture
 Back-plane (Switching Fabric): 1.6Gbps
 2K MAC Address Table

 Power Input

 DC 12V/48V Redundant Power Input

 Operating Temperature

 Wide Operating Temperature: -40°C ~ 75°C

 Case/Installation

 IP-30 Protection
 Installation in a Pollution Degree 2 environment

 DIN Rail and Wall Mount Design
 Provides EFT protection 3,000 VDC for power line
 Supports 6,000 VDC Ethernet ESD protection

2

Technical Specification

The technical specifications of IPES-0008A-12V Industrial Switch are listed as follows.

Communications

Compatibility

IEEE 802.3, 802.3u, 802.3x, 802.3af

LAN

10/100Base-T

Transmission Speed

Up to 100 Mbps

Interface

Connectors

8 x RJ-45 (8-port 10/100TX)

6-pin removable screw terminal (Power & Relay)

LED Indicators

Unit: Power1, Power2, P-Fail, PoE

Ethernet port: Link/Active, Speed

PoE

Power Output

Per port 48 VDC, 15.4 Watts

Pin Assignment

RJ-45 port #1 ~ # 4 support IEEE 802.3af

End-point, Alternative A mode.

Positive (VCC+): RJ-45 pin 1, 2.

Negative (VCC-): RJ-45 pin 3, 6.

Data (1,2,3,6 )

Power

Power Consumption

10 Watts (Max.); POE Power Budget:240 Watts
(48V input); 90W(12V); 120W(24V input)

Power Input

External Power Supply: DC 12~48V, Redundant
power D12V~DC 48V and connective removable
terminal block.

Fault Output

1 Relay Output

3

Mechanism

Dimensions (WxHxD)

74mm (W) x 115mm (D) x 152mm (H)

Enclosure

IP-30, Metal shell with solid mounting kits

Mounting

DIN-Rail, Wall Mount

Protection

ESD (Ethernet)

6,000 VDC

Surge (EFT for power)

3,000 VDC

Power Reverse

Yes

Overload current protection

Yes

Environment

Operating Temperature

Standard: -20°C~60°C /-4°F~140°F
E models:-40°C~75°C / -40°F~167°F

Operating Humidity

5% ~ 95% (non-condensing)

Storage Temperature

-40 ~ 85oC

Storage Humidity

5% ~ 95% (non-condensing)

Certifications

EMC

FCC Class A

CE EN61000-6-2

CE EN61000-6-4

CE EN61000-4-2 (ESD)

CE EN61000-4-3 (RS)

CE EN61000-4-4 (EFT)

CE EN61000-4-5 (Surge)

CE EN61000-4-6 (CS)

CE EN61000-4-8 (Magnetic Field)

Free Fall

IEC60068-2-32

Shock

IEC60068-2-27

Vibration

IEC60068-2-6