Lanner electronic FW-7650 User Manual

FW-7650 Series

19” 1U Intel Pentium4 / Celeron Rackmount

Network Security Platform

User’s Manual

Copyright and Disclaimers

© Copyright 2004 - Lanner Electronics Inc.
All Rights Reserved

The contents in this publication have been thoroughly checked and considered accurate. The
publisher and manufacturer of this product, Lanner Electronics, is not responsible for any
violation of patents or other rights of third parties resulting from its use. Neither does Lanner
Electronics assume any responsibility for any inaccuracies contained in this manual, nor make
any commitment to keep the information in this document up-to-date.

Lanner reserves the right to make improvements to this document and/or this product at any
given time without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means (electronic, mechanical, photocopying, recording, or otherwise, without
the formal consent from Lanner.

Trademark Acknowledgments

All products and/or brand names stated in this publication are the trademarks of their rightful
and associated companies.

Radio Frequency Emissions Notice

This equipment has been tested and found to comply with the digital device limits pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when operate in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area may cause harmful interference, in which case the user will
be required to correct the interference at his expense.

ii

Safety Instructions

The following information relates to the safety of installation and maintenance personnel. Read
all instructions before attempting to unpack, install or operate this equipment, especially before
connecting the power adapter.

Please keep the following in mind as you unpack and install this equipment:

 Always follow basic safety precautions to reduce the risk of fire, electrical shock and

injury to persons.

 Do not apply power into FW-7650 before installation or when disconnecting this

product from its original system setup.

 To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this

product near water.

 Locate a safe and dry location to place this product. Keep it away from wet

surfaces/surroundings.

 Never push an object of any kind into this product through openings or empty slots, as

you may damage parts.

 Do not attach the power supply cabling to building surfaces. Do not allow anything to

rest on the power cabling or allow it to be abused by persons walking on it.

 Distance your working area from moist floors, ungrounded power extension cables, and

unavailable safety grounds.

 Avoid installation of this product during a lighting storm.
 Damages caused by electrostatic discharge may result in total or intermittent system

failures. To minimize the possibility of ESD damage, an anti-static strap is highly
recommended.

 When cleaning or servicing this unit, avoid using highly toxic or aerosol cleaners. Use a

clean damp cloth when wiping its surfaces.

 Do not place this device in a tight and sealed location. Place the unit where it can access

sufficient airflow to its vent holes (openings along its sides). Never block or cover these
openings.

 Do not disassemble this product on your own.

iii

Getting Technical Assistance

Should you encounter questions or problems with your FW-7650, Lanner Electronics is ready
to assist you within the guidelines of our product support programs. First, check the electronic
product documentation for assistance. If you still cannot find the solution to your problem,
contact Lanner sales team with the following information handy:

 FW-7650 model name
 Part number
 Local network configuration details
 The abnormal behavior and/or error messages reported by your network system
 Your questions, or a description of the problem you are experiencing

Call, fax, or e-mail Lanner Electronics for technical support.

Phone: [phone]

Fax: [phone]

E-mail: [e-mail]

About this Manual

This target audience of this manual includes users, administrators and technicians. This
publication is a useful reference when installing, configuring, operating and managing the
FW-7650. This breakdown and short descriptions of this manual’s contents are as follows:

 Chapter 1 – Introduction provides an overview of the FW-7650 19” 1U

Rackmount network security appliance, including its related features,
application usage and technical specifications list. The chapter also
guides users through the pre and post installation process by listing safety
tips plus an overall detailed description of the control board and system
and their vital components.

 Chapter 2 – Introduce Hardware Installation
 Chapter 3 – Award BIOS Setup
 Appendix A –summarizes the specification of the power supply
 Appendix B –Watchdog Timer Introduction
 Appendix C –Console Redirection
 Appendix D– LCD Module and Key Pad

iv

Table of Contents

Copyright and Disclaimers....................................................................................................ii

Trademark Acknowledgments...............................................................................................ii

Radio Frequency Emissions Notice..................................................................... ii

Safety Instructions............................................................................................... iii

Getting Technical Assistance.............................................................................. iv

About this Manual................................................................................................ iv

Table of Contents................................................................................................ v

C h a p t e r 1.........................................................................................................................1

Getting Started 1

1.1 Introduction.................................................................................................. 1

1.1.1 Features...............................................................................................................................1

1.2 Technical Specifications.............................................................................. 2

1.3 Packing Contents........................................................................................ 3

1.4 MB-X71 System Board................................................................................4

1.4.1 Board Layout........................................................................................................................4

1.4.2 Jumper Settings and I/O Connector.....................................................................................5

1.4.3 Connector Pin Assignments.................................................................................................6

SFC1:Master/Slave Select ................................................................................. 6

CMOS1:Clear CMOS Data ............................................................................... 6

FAN1~3 : 3 Pin FAN Connector.................................................................... 6

LANA1~2 :Type 1 ( RJ-45)............................................................................... 6

LANA3~6 :Type 1 ( RJ-45).............................................................................. 7

COMA1: RS-232 Serial Port #1 Connector ( D-Sub) ................................ 7

PKMB1:PS/2 Keyboard & Mouse Connector (2x4 Header 2.54mm)..... 7

PSA1:20 Pin ATX Power Connector........................................................... 7

PSA1:20 Pin ATX Power Connector........................................................... 8

PS4P1:4-Pin Power Connector (P4-4P Male ).......................................... 8

KPA1：LCM Keypad...................................................................................... 8

LCMA1：LCM CONNECTOR....................................................................... 8

VGAB1 : External VGA Connector ( 12 Pin Header )...................................... 9

IDEA1 : IDE Interface Connector ( 44Pin 2.0mm Pitch Header ) .................... 9

PLRS1:Power LED,HD LED,Reset,Speaker Connector(11 Pin 2.54mm )..... 10

FDCA1 : Floppy Interface Connector ( 34 Pin Header )................................. 10

CF1:Compact Flash Connector...................................................................11

LEDE1：2x22 Pin......................................................................................... 12

IDEB1 : IDE Interface Connector ( 40Pin 2.54mm Pitch Header).................. 13

PCIB1:124 Pin Mini PCI Socket..................................................................... 14

PCIB1:124 Pin Mini PCI Socket(Continued last page)............................... 15

1.5 FW-7650 19” 1U Rackmount Firewall Mechanisms.................................... 16

1.5.1 Face Panel...........................................................................................................................16

1.5.3 Rear View.............................................................................................................................17

C h a p t e r 2.......................................................................................................................18

FW-7650 Hardware Installation Guide..............................................................................18

2.1 Hardware Installation Guide........................................................................ 18

Chapter 3..............................................................................................................................22

Award BIOS Setup..............................................................................................................22

3.1 BIOS Setup ................................................................................................. 22

3.2 CMOS Setup Utility ...................................................................................... 23

3.3 Standard CMOS Features........................................................................... 25

v

3.4 BIOS Features Setup .................................................................................. 27

3.5 Chipset Features Setup............................................................................... 30

3.6 Integrated Peripherals................................................................................. 32

3.7 Power Management Setup.......................................................................... 34

3.8 PnP/PCI Configuration ................................................................................ 36

3.9 PC Health Status......................................................................................... 40

3.10 Load Optimized Defaults............................................................................. 41

3.11 Supervisor/User Password Setting ........................................................... 41

3.12 Save and Exit Setup................................................................................... 41

3.13 Exit Without Saving ..................................................................................... 42

Appendix A...........................................................................................................................43

Power Supply 43

Appendix B ..........................................................................................................................44

W atchdog Timer 44

A p p e n d i x C...................................................................................................................46

Console Redirection ............................................................................................................46

A p p e n d i x D ..................................................................................................................47

LCD Module and Key Pad For FW-7650...........................................................................47

Terms and Conditions........................................................................................................................ 49

Warranty Policy 49
RMA Service 49

vi

1.1 Introduction

The FW-7650 is a 1U rackmount network security solution targeting the Enterprise market.
The FW-7650 supports Petium4 /Celeron processor with 400/533MHz FSB. It is designed
with an Intel 845GV as its northbridge and ICH4(82801DB) as its southbridge.; To enhance
network security appliance
and six Ethernet LAN ports from 10/100Mbit up to Gigabit to provide an ideal
price/performance solution for building a wide range of desktop and set top boxes to thin
clients and web terminals powerful computing and multimedia performance for all the most
popular productivity and Internet applications.

C h a p t e r 1

Getting Started

Figure 1 – FW-7650 Outlook

, FW-7650 comes with Intel 82540EM & 82551QM Ethernet chips

Designed with the Plug-and-Serve concept in mind, the FW-7650 Series offers two DDR
200/266/333 DIMM Socket support up to 2GB RAM which provide full functionality and
performance to be used "exactly" where you need it as well. In addition, one ATA mode
CompactFlash type II socket used in installing OS avoiding service disruption caused by hard
disk's mechanical/magnetic failures.

The FW-7650 has a Mini PCI slot, users can expand their specifications and performance by
simply adding add-on cards to the slot. The FW-7650 is a powerful and flexible unit that can
meet the vast and various hardware requirement and performance needs of System Integrators,
OEM customers and software developers.

1.1.1 Features

Listed below are the key features of FW-7650.

 Supports 2.5” HDD
 Socket 478 for Intel® Pentium™ 4/Celeron Processor, up to 2.4GHz, 400/ 533MHZ FSB
 Two DDR200/266/333 DIMM Socket, up to 2GB RAM
 Supports Two Gigabit Ethernet ports, with two Intel 82540EM chipset. And Four 10/100

Ethernet ports, with four intel 82551QM chipset

 Supports Compact Flash, Serial(RS-232), and Mini PCI.
 19”1U Rackmount network security appliance
 Suitable Network applications; Virtual Private Network(VPN), Firewall, IDS, …

1

1.2 Technical Specifications

Model Name FW-7650

SBC

SBC
CPU

Chipset

BIOS

Memory

Network interface

SSD

I/O Interface

Expansion Slot

RTC

Power

MB-X71

Socket 478 for Intel® Pentium™ 4/Celeron Processor ,

up to 2.4GHz,533MHZ FSB

Intel® 845GV chipset (pin-to-pin compatible with

845G series); 82801DB I/O Controller Hub 4 (ICH4)

Award BIOS

Two DDR200/266/333 DIMM Socket, up to 2GB RAM

A. Two Intel 82540EM 32bit Gb Ethernet Controller (Colay

with 82551QM)

B. Four Intel 82551QM 10/100 Mb Ethernet Controller

Two CompactFlash TypeII Socket

One DB-9 RS-232 connector

One Mini-PCI slot

Internal RTC with LI battery

200W ATX Power Supply

Mechanical/ Environmental

Form Factor

Operating Temperature

Storage Temperature

Humidity

Chassis Material

Dimension

Net Weight

Certification

Software support

19” 1U Rackmount

o

0

C – 40 oC

o

-20

C – 70 oC

5% - 95% RH, non-condersing

Steel

428x303x44 mm

5.4 KGS

CE, FCC CLASS A

Linux 6.5 and above, Windows 2000/2003/ XP

2

1.3 Packing Contents

Carefully unpack your package and make sure that you have the following items.

 FW-7650 Network security Platform
 Console cable
 1.8 meters long cross-over Ethernet cable
 1.8 meters long straight-through Ethernet cable
 Face panel name plate label
 Power cable
 Drivers and User’s Manual CD
 Screw Set
 Slid & Bracket Set

If you find anything missing or damaged, promptly contact your dealer for assistance.

3

1.4 MB-X71 System Board

MB-X71 is the system board bundled with the FW-7650 Network security platform. The
succeeding sections list all MB-X71 related jumper settings and connector pin assignments.

1.4.1 Board Layout

Figure 3 – MB-X71 Jumpers and Connectors

4

1.4.2 Jumper Settings and I/O Connector

The onboard jumper settings and I/O connector of MB-X71 are custom-tailored to fit the
FW-7650 functionality. Changing the jumper settings may result in system malfunction or
unforeseen damages.

Jumper Settings and I/O Connector Summary for MB-X71

JUMPER FUNCTION

CMOS1 Clear CMOS Data

SCF1 Master/Slave Select

FAN1-3 3 Pin Fan Connector
LANA1~2 Type 1 ( RJ-45 )
LANA3~6 Type 1 ( RJ-45)

COM1 RS232 Serial Port #1 Connector (D-Sub)

PKMB1 PS/2 Keyboard & Mouse Connector (2x4 Header 2.54mm )

PSA1 20 Pin ATX Power Connector

PS4P1 4-Pin Power Connector (P4-4P Male )

KPA1 LCM Keypad
LCMA1 LCM CONNECTOR
VGAB1 External VGA Connector ( 12 Pin Header )

IDEA1 IDE Interface Connector ( 44 Pin 2.0mm Pitch Header )
IDEB1 IDE Interface Connector ( 40 Pin 2.54mm Pitch Header )

PLRS1 Power LED, Reset, Speaker Connector

FDCA1 Floppy Interface Connector (34 Pin Header)

CF1 Compact Flash Connector

LEDE1 2x22 Pin

PCIB1 124 Pin Mini PCI Socket

5

1.4.3 Connector Pin Assignments

SFC1:Master/Slave Select

Compact Flash Card ATA Disk Chip SCF1

Master Slave 1-2

Slave Master 2-3(Default

CMOS1:Clear CMOS Data

CMOS1 Description

1-2 Normal (Default)
2-3 Clear CMOS

FAN1~3 : 3 Pin FAN Connector

Pin No. Description

1 Ground
2 +12V
3 FAN Status

LANA1~2 :Type 1 ( RJ-45)

Pin No.

Fast Ethernet Giga Ethernet

1 TX+ MD0+
2 TX- MD0­3 RX+ MD1+
4 T45 MD2+
5 T45 MD2­6 RX- MD1­7 T78 MD3+
8 T78 MD3-

Description

LANA1~2

6

LANA3~6 :Type 1 ( RJ-45)

Pin No. Description

1 TX+
2 TX­3 RX+
4 T45
5 T45
6 RX­7 T78
8 T78

COMA1: RS-232 Serial Port #1 Connector ( D-Sub)

Pin No. Description

1 Data Carrier Detect ( DCDA # )
2 Receive Data ( RXDA )
3 Transmit Data ( TXDA )
4 Data Terminal Ready ( DTRA # )
5 Ground ( GND )
6 Data Set Ready ( DSRA # )
7 Request To Send ( RTSA # )
8 Clear To Send ( CTSA # )
9 Ring Indicator ( RIA # )

COMA1

PKMB1:PS/2 Keyboard & Mouse Connector (2x4 Header 2.54mm)

Pin No. Description Pin No. Description

1 KBCLK 2 GND
3 NC 4 KBDATA
5 NC 6 MSDATA
7 MSCLK 8 VCC

7

PSA1:20 Pin ATX Power Connector

Pin No. Description Pin No. Description

1 +3.3V 11 +3.3V
2 +3.3V 12 -12V
3 GND 13 GND
4 +5V 14 SWITCH
5 GND 15 GND
6 +5V 16 GND
7 GND 17 GND
8 Power Good 18 -5V
9 Stand-By 5V 19 +5V

10 +12V 20 +5V

PS4P1:4-Pin Power Connector (P4-4P Male )

Pin No. Description

1 GND
2 GND
3 +12V
4 +12V

KPA1：LCM Keypad

Pin No. Description

1 KPA1
2 KPA2
3 KPA3
4 KPA4

LCMA1：LCM CONNECTOR

Pin No. Description Pin No. Description

1 VCC 2 PGND
3 LSTIN- 4 VEE
5 LAFD- 6 LINIT­7 LPD1 8 LPD0

9 LPD3 10 LPD2
11 LPD5 12 LPD4
13 LPD7 14 LPD6
15 LCD 16 VCC

8

VGAB1 : External VGA Connector ( 12 Pin Header )

Pin No. Description Pin No. Description

1 R 2 Ground

3 G 4 Ground

5 B 6 Ground

7 H-SYNC 8 Ground

9 V-SYNC 10 Ground
11

Detect-display

Data

12

IDEA1 : IDE Interface Connector ( 44Pin 2.0mm Pitch Header )

Pin No. Description Pin No. Description

1 Reset # 2 Ground

3 Data 7 4 Data 8

5 Data 6 6 Data 9

7 Data 5 8 Data 10

9 Data 4 10 Data 11
11 Data 3 12 Data 12
13 Data 2 14 Data 13
15 Data 1 16 Data 14
17 Data 0 18 Data 15
19 Ground 20 NC
21 DMA REQ # 22 Ground
23 IOW # 24 Ground
25 IOR # 26 Ground
27 IOCHRDY 28 Ground
29 DMA ACK # 30 Ground
31 Interrupt 32 NC
33 SA 1 34 NC
35 SA 0 36 SA 2
37 HDC CS 0# 38 HDC CS 1#
39 HDD Active 40 Ground
41 VCC 42 VCC
43 Ground 44 NC

Deteck-display

CLOCK

9

PLRS1:Power LED,HD LED,Reset,Speaker Connector(11 Pin 2.54mm )

Pin No. Description

1 Power LED +
2 Power LED +
3 GND
4 HDD LED +
5 HDD LED ­6 RESET SW +
7 RESET SW – (GND)
8 External Speaker ­9 Internal Buzzer -

10 NC

11 External S peaker +

FDCA1 : Floppy Interface Connector ( 34 Pin Header )

Pin No. Description Pin No. Description

1 Ground 2 Density Select

3 Ground 4 NC

5 Ground 6 DS1

7 Ground 8 Index #

9 Ground 10 Motor Enable A #
11 Ground 12 Drive Select B #
13 Ground 14 Drive Select A #
15 Ground 16 Motor Enable B #
17 Ground 18 Direction #
19 Ground 20 Step #
21 Ground 22 Write Data #
23 Ground 24 Write Gate #
25 Ground 26 Track 0 #
27 Ground 28 Write Protect #
29 NC 30 Read Data #
31 Ground 32 Head Side Select #
33 NC 34 Disk Change #

10

CF1:Compact Flash Connector

Pin No. Description Pin No. Description

1 GND 26 CD1-

2 DATA3 27 DATA11

3 DATA4 28 DATA12

4 DATA5 29 DATA13

5 DATA6 30 DATA14

6 DATA7 31 DATA15

7 CE1# 32 CE2#

8 A10 33 VS1#

9 OE# 34 IOR#
10 A9 35 IOW#
11 A8 36 WE#
12 A7 37 READY#
13 CFVCC3 38 CFVCC3
14 A6 39 CSEL
15 A5 40 VS2#
16 A4 41 RESET
17 A3 42 WAIT#
18 A2 43 INPACK#
19 A1 44 REG#
20 A0 45 DASP#
21 DATA0 46 DIAG#
22 DATA1 47 DATA8
23 DATA2 48 DATA9
24 WP 49 DATA10
25 CD2- 50 GND

11

LEDE1：2x22 Pin

Pin No. Description Pin No. Description

1 POWER LED 2 POWER LED

3 POWER LED STATUS 4 POWER LED STA TUS

5 Lan1 Link/Active LED- 6 Lan1 Link/Active LED+

7 Lan1 100 LED- 8 Lan1 100 LED+

9 Lan1 1G LED- 10 Lan1 1G LED+
11 Lan2 Link/Active LED- 12 Lan2 Link/Active LED+
13 Lan2 100 LED- 14 Lan2 100 LED+
15 Lan2 1G LED- 16 Lan2 1G LED+
17 Lan3 Link/Active LED- 18 Lan3 Link/Active LED+
19 Lan3 100 LED- 20 Lan3 100 LED+
21 Lan3 1G LED- 22 Lan3 1G LED+
23 Lan4 Link/Active LED 24 Lan4 Link/Active LED
25 Lan4 100 LED 26 Lan4 100 LED
27 Lan4 1G LED 28 Lan4 1G LED
29 Lan5 Link/Active LED 30 Lan5 Link/Active LED
31 Lan5 100 LED 32 Lan5 100 LED
33 Lan5 1G LED 34 Lan5 1G LED
35 Lan6 Link/Active LED 36 Lan6 Link/Active LED
37 Lan6 100 LED 38 Lan6 100 LED
39 Lan6 1G LED 40 Lan6 1G LED
41 NC 42 NC
43 NC 44 NC

12