Lang Manufacturing MM36C-E-CLS Service Manual

Installation, Operation, Maintenance, & Troubleshooting

Model: MM36C-E-CLS

Serial:

Electric Cruise Line Cheese-melter

Lang Manufacturing Company 6500 Merrill Creek Parkway Everett, WA 98203

Phone: [phone] Fax: [phone]

WWW.LANGWORLD.COM © Copyright 2000

THIS MANUAL MUST BE RETAINED FOR FUTURE REFERENCE.
READ, UNDERSTAND AND FOLLOW THE INSTRUCTIONS AND
WARNINGS CONTAINED IN THIS MANUAL.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY OR DEATH. READ THE
INSTALLATION, OPERATING AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR
SERVICING THIS EQUIPMENT.

NOTICE:

THIS EQUIPMENT IS APPROVED FOR INSTALLATION ONLY ON

VESSELS GREATER THAN 65 FEET IN LENGTH, IN
ACCORDANCE WITH USCG REGULATIONS IN TITLE 46 CFR
110-113. ANY WIRING USED IN THE INSTALLATION OF THIS
APPLAINCE MUST BE STRANDED COPPER.

2

TABLE OF CONTENTS

CHAPTER PAGE

1. TABLE OF CONTENTS................................................................................3

2. READ FIRST..................................................................................................4

3. UNPACKING.................................................................................................6

4. INSTALLATION............................................................................................7

5. OPERATION..................................................................................................9

6. CLEANING & MAINTENANCE PROCEDURES......................................10

7. TROUBLESHOOTING..................................................................................11

8. PARTS LISTS.................................................................................................13

9. EXPLODED VIEW........................................................................................14

10. WIRING DIAGRAM......................................................................................19

11. WARRANTY..................................................................................................20

3

IMPORTANT READ FIRST IMPORTANT

CAUTION:

CAUTION:

CAUTION:

DANGER:

WARNING:

CHEESE-MELTER WEIGHS 135 lbs (61.24 kg). FOR
SAFE HANDLING, INSTALLER SHOULD OBTAIN
HELP AS NEEDED, OR EMPLOY APPROPR IATE
MATERIALS HANDLING EQUIPMENT (SUCH AS A
FORKLIFT, DOLLY, OR PALLET JACK) TO REMOVE
THE UNIT FROM THE SKID AND MOVE IT TO THE
PLACE OF INSTALLATION.

ANY STAND, COUNTER OR OTHER DEVICE ON
WHICH THE CHEESE-MELTER WILL BE LOCATED
MUST BE DESIGNED TO SUPPORT THE WEIGHT OF
THE UNIT.

SHIPPING STRAPS ARE UNDER TENSION AND CAN
SNAP BACK WHEN CUT.

THIS APPLIANCE MUST BE GROUNDED AT THE
TERMINAL PROVIDED. FAILURE TO GROUND THE
APPLIANCE COULD RESULT IN ELECTROCUTION
AND DEATH.

INSTALLATION OF THE UNIT MUST BE DONE BY
PERSONNEL QUALIFIED TO WORK WITH
ELECTRICITY. IMPROPER INSTALLATION CAN
CAUSE INJURY TO PERSONNEL AND/OR DAMAGE
TO EQUIPMENT. UNIT MUST BE INSTALLED IN
ACCORDANCE WITH ALL APPLICABLE CODES.

NOTICE:

NOTICE:

CAUTION:

CAUTION:

The data plate is located on the left side of the unit in
the lower front corner. The voltage, wattage, serial
number, wire size, and clearance specifications are
on the data plate. This information should be
carefully read and understood before proceeding
with the installation.

The installation of any components such as a vent
hood, grease extractors, fire extinguisher systems,
must conform to their applicable National, State and
locally recognized installation standards.

ALWAYS KEEP THE AREA NEAR THE APPLIANCE
FREE FROM COMBUSTIBLE MATERIALS.

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN
AND DRY. IF SPILLS OCCUR, CLEAN IMMEDIATELY,
TO AVOID THE DANGER OF SLIPS OR FALLS.

4

IMPORTANT READ FIRST IMPORTANT

WARNING:

CAUTION:

NOTICE:

WARNING:

CAUTION:

KEEP WATER AND SOLUTIONS OUT OF CONTROLS.
NEVER SPRAY OR HOSE CONTROL CONSOLE,
ELECTRICAL CONNECTIONS, ETC.

MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES,
MUCOUS MEMBRANES AND CLOTHING.
PRECAUTIONS SHOULD BE TAKEN TO WEAR RUBBER
GLOVES, GOGGLES OR FACE SHIELD AND
PROTECTIVE CLOTHING. CAREFULLY READ THE
WARNING AND FOLLOW THE DIRECTIONS ON THE
LABEL OF THE CLEANER TO BE USED.

Service on this, or any other, LANG appliance must be
performed by qualified personnel only. Consult your
authorized service station directory or call the factory at
1-800-224-LANG (5264), or
for the service station nearest you.

BOTH HIGH AND LOW VOLTAGES ARE PRESENT
INSIDE THIS APPLIANCE WHEN THE UNIT IS
PLUGGED/WIRED INTO A LIVE RECEPTACLE. BEFORE
REPLACING ANY PARTS, DISCONNECT THE UNIT
FROM THE ELECTRIC POWER SUPPLY.

USE OF ANY REPLACEMENT PARTS OTHER THAN
THOSE SUPPLIED BY LANG OR THEIR AUTHORIZED
DISTRIBUTORS CAN CAUSE BODILY INJURY TO THE
OPERATOR AND DAMAGE TO THE EQUIPMENT AND
WILL VOID ALL WARRANTIES.

WWW.LANGWORLD.COM

5

3.1 Receiving the Cheese-melter

Upon receipt, check for freight damage, both visible and concealed. Visible
damage should be noted on the freight bill at the time of delivery and signed by the
carrier's agent. Concealed loss or damage means loss or damage which does not
become apparent until the merchandise has been unpacked. If concealed loss or
damage is discovered upon unpacking, make a written request for inspection by the
carrier's agent within 15 days of delivery. All packing material should be kept for
inspection. Do not return damaged merchandise to Lang Manufacturing Company.
File your claim with the carrier.

3.2 Location

Prior to un-crating, move the cheese-melter as near its intended location as
practical. The crating will help protect the unit from the physical damage normally
associated with moving it through hallways and doorways.

3.3 Un-crating

The cheese-melter will arrive completely assembled inside a wood frame covered
by cardboard box and strapped to a skid.

straps and remove the wood frame.

Remove the cardboard cover, cut the

UNPACKING

The unit back is not attached to the machine. It is packaged loose behind the
Cheese-melter.

The screws used to attach the back to the cheese-melter are screwed into the rear
edge of the machine.

CAUTION:

CAUTION:

CAUTION:

Remove cheese-melter from skid and place in intended location.

CHEESE-MELTER WEIGHS 135 lbs (61.24 kg). FOR
SAFE HANDLING, INSTALLER SHOULD OBTAIN HELP
AS NEEDED, OR EMPLOY APPROPRIATE MATERIALS
HANDLING EQUIPMENT (SUCH AS A FORKLIFT,
DOLLY, OR PALLET JACK) TO REMOVE THE UNIT
FROM THE SKID AND MOVE IT TO THE PLACE OF
INSTALLATION.

ANY STAND, COUNTER OR OTHER DEVICE ON WHICH
CHEESE-MELTER WILL BE LOCATED MUST BE
DESIGNED TO SUPPORT THE WEIGHT OF THE UNIT.

SHIPPING STRAPS ARE UNDER TENSION AND CAN
SNAP BACK WHEN CUT.

6