Lang Manufacturing Chef Installation Manual

Owner’s Manual

Chef Series Sectional Range

IMPORTANT FOR FUTURE REFERENCE

Please complete this information and retain
this manual for the life of the equipment:

Model #: __________________________
Serial #: __________________________
Date Purchased: ___________________

Charbroiler Models
Flush Open Burner Models
Graduated Hot-Top Models

Uniform Hot-Top Models

Standard Griddle Models

Step-Up Open-Burner Models

Thermostatic Griddle Models

Combination Open-Burner Hot-Top Models

Combination Open-Burner Griddle Models

WARNING

Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death.
Read installation, operation, and maintenance instructions thoroughly before installing or servicing this equipment.

10 Sunnen Drive, St. Louis, MO 63143 USA • www.langworld.com

M

ANUAL 1192040 REV 1 (01/10)

$30.00

CHEF SERIES SECTIONAL RANGE

MANUAL SECTION SR

SAFETY PRECAUTIONS CHEF SERIES SECTIONAL RANGE

SAFETY PRECAUTIONS

Before installing and operating this equipment, be sure everyone involved in its operation is fully trained and aware of
precautions. Accidents and problems can be caused by failure to follow fundamental rules and precautions.

The following symbols, found throughout this manual, alert you to potentially dangerous conditions to the operator,
service personnel, or to the equipment.

DANGER

WARNING

CAUTION

NOTICE

This symbol warns of immediate hazards that will result in severe injury or death.

This symbol refers to a potential hazard or unsafe practice that could result in injury or

death.

This symbol refers to a potential hazard or unsafe practice that could result in injury,

product damage, or property damage.

This symbol refers to information that needs special attention or must be fully understood,

even though not dangerous.

WARNING

FIRE HAZARD

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of cookin g appliances.
Keep area around cooking appliances free and clear of combustibles.
Purchaser of equipment must post in a prominent location detailed instructions to be followed in the event the

operator smells gas. Obtain the instructions from the local gas supplier.

WARNING

BURN HAZARD

Contact with hot surfaces will cause severe burns. Always use caution when operating cooking appliances.

WARNING

EXPLOSION AND ASPHYXIATION HAZARD

In the event a gas odor is detected, shut down equipment at the main gas shut-off valve and immediately call
the emergency phone number of your gas supplier.

Improper ventilation can result in headaches, drowsiness, nausea, and could result in death. Do not obstruct the
flow of combustion and ventilation air to and from cooking appliances.

WARNING

ELECTRIC SHOCK HAZARD

For appliances that use electric power, disconnect the power to the appliance before cleaning. Do not remove
panels that require tools to remove.

NOTICE

Lang appliances are intended for commercial use only. Not for household u se.
Warranty will be void if service work is performed by other than a qualified technician, or if other than genuine

Lang replacement parts are installed.
Give this Owner’s Manual and important papers to the proper authority to retain for future reference.

Published in the United States of America.

PAGE 2 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE INTRODUCTION

INTRODUCTION

Congratulations! You have purchased one of the finest pieces of heavy-duty commercial cooking equipment on the
market.

You will find that your new equipment, like all Lang equipment, has been designed and manufactured to meet the
toughest standards in the industry. Each piece of Lang equipment is carefully engineered and designs are verified
through laboratory tests and field installations. With proper care and field maintenance, you will experien ce years of
reliable, trouble-free operation. For best results, read this manual carefully.

RETAIN THIS MANUAL FOR FUTURE REFERENCE.
This manual is for Lang Chef Series Sectional Ranges.
This manual does NOT cover sectional fryers, fryer filter systems, salamander broilers, upright broilers, cheese

melters, or refrigerated bases. Those appliances have their own manuals.
The location of the serial plate depends on the type of base (see

serial plate is located on the backside of the kick-plate below the oven door (lift the kick-plate straight up and tilt the
top edge out and down.) On models with a cabinet base, the serial plate is located inside the left cabinet door. On
modular (countertop) models, the serial plate is located inside the front valve panel.

Read these instructions carefully before attempting installation. Installation and initial startup should be performed by
a qualified installer. Unless the installation instructions for this product are followed by a qualified service technician (a
person experienced in and knowledgeable with the installation of commercial gas and/or electric cooking equipment)
then the terms and conditions on the Manufacturer’s Limited Warranty will be rendered void and no warranty of any
kind shall apply.

In the event you have questions concerning the installation, use, care, or service of the product, contact:

Lang Technical Service

10 Sunnen Drive

St. Louis, MO 63143 USA

Phone: [phone] Fax: [phone]

www.langworld.com

Figure 1

Location of Serial Plate

Figure 1 below). On models with oven bases, the

Location of Serial Plate

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 3 OF 76

SPECIFICATIONS CHEF SERIES SECTIONAL RANGE

SPECIFICATIONS

NOTICE

Local codes regarding installation vary greatly from one area to another. The National Fire Protection Association,
Inc., states in its NFPA 96 latest edition that local codes are the “authority having jurisdiction” when it comes to
installation requirements for equipment. Therefore, installations should comply with all local codes.

Lang reserves the right to change specifications and product design without notice. Such revisions do not entitle
the buyer to corresponding changes, additions, or replacements for previously purchased equipment.

Lang appliances are intended for commercial use only, not for household use.
The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1, Natural Gas Installation Code, CAN/CGA-B149.1, or the Propane Installation Code CAN/CGA-
B149.2, as applicable, including:

1. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).

2. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.45
kPa).

CLEARANCES

WARNING

MINIMUM CLEARANCES FROM COMBUSTIBLE CONSTRUCTION

There must be adequate clearance between the sectional range and combustible construction. Clearance must
also be provided for servicing and for operation.

Open-Top

Standard-Burner

Models

Sides 10" 13" 10" 10" 6"

Back 6" 6" 12" 12" 6"

Floor* 0" 0" 0" 0" 0"

Do NOT install sectional charbroilers next to combustible materials.

* Models with 6" legs or casters are suitable for installation on combustible floors.
Adequate clearance must be provided in the aisle in front of the unit to permit operation (including opening of

doors and/or removal of grease drawers, drippings trays, and/or oven racks), as well as for servicing. No ad ditional
clearance is required for servicing as the sectional range is serviceable from the front.

Models with a convection-type oven require a minimum clearance of 2" between the motor on the back and non­combustible construction. Care must be taken to provide adequate air circulation to prevent the motor from
overheating.

Open-Top

45K-Burner

Models

Griddle
Models

Uniform Hot-Top

Models

Graduated

Hot-Top

Models

Minimum clearance from noncombustible construction is zero on the sides and back for all models (except for
models with a convection-type oven).

The high-temperature flue products flow out through the top of the flue riser of all models, and from the top of
open-top and charbroiler models. Installation under a vented hood is recommended.

Salamander broilers and cheese melters mounted on the flue riser of a sectional range may require additional
minimum clearances (see the documentation for those appliances).

PAGE 4 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE SPECIFICATIONS

VENTILATION

WARNING

Improper ventilation can result in personal injury or death. Ventilation which fails to properly remove flue products
can cause headaches, drowsiness, nausea, or could result in death.

All gas appliances must be installed in such a manner that the flow of combustion and ventilation air is not
obstructed. Provisions for adequate air supply must be provided. Do not obstruct the area under the control panel
or below the oven door (on the front), or the area below the flue riser (on the back) as combustion air enters
through these areas.

NOTICE

Proper ventilation is the owner’s responsibility. Any problem due to improper ventilation will not be covered by the
warranty.

Be sure to inspect and clean the ventilation system according to the ventilation equipment manufacturer’s
instructions.

Air for combustion enters from the front below the valve panel, as well as from the rear into the burner box. Ranges
with solid tops (griddles and hot-tops) vent their flue products up the flue riser. On units with a base oven, combustion
air enters from the front below the oven door. Oven flue products are vented up the flue riser.

Lack of sufficient ventilation will cause poor burner and pilot operating characteristics, resulting in inefficient
performance. Such conditions also cause high ambient temperatures at the manifold area and create valve and
thermostat problems.

If a ventilation canopy is used, it is recommended that the canopy extend 6" past the sectional range and that the
bottom edge be located 6'6" from the floor. Filters should be installed at an angle of 45° or more from the horizontal.
This position prevents dripping grease, and facilitates collecting the run-off grease in a drip pan under the filter.

A strong exhaust fan tends to create a vacuum in the room and may interfere with burner performance or may
extinguish pilot flames. Fresh air openings approximately equal to the fan area will relieve such a vacuum. The
exhaust fan should be installed at least 2" above the top of the flue riser.

If the sectional range is connected directly to an outside flue, a CSA design certified down draft diverter must be
installed.

In case of unsatisfactory performance by any gas appliance, check the appliance with the exhaust fan turned OFF. Do
this only long enough to check whether doing so corrects any problems with equipment performance. Then turn the
exhaust fan back on and let it run to remove any exhaust that may have accumulated during the test.

GAS SUPPLY

The sectional range is design-certified for operation on natural or propa ne gases. The sectional range is shipped
configured and adjusted for the type of gas specified by the purchaser, which is indicated on the serial plate (see
Figure 1 on page 3). Connect the sectional range ONLY to the type of gas for which it is configured and adjusted.

Each section has a 1-1/4" front gas manifold that can be coupled to adjacent section(s). Sections can be ordered with
an optional 1" rear gas connection with a male NPT connector. Minimum supply pressure is 7" W.C. for natural gas,
11" W.C. for propane. An external pressure regulator and shut off valve must be provided. If using a flexible-hose gas
connection, the I.D. of the hose must not be smaller than the connector on the unit and must comply with ANSI
Z21.69. Provide an adequate means of restraint to prevent undue strain on the gas connection.

If applicable, the vent line from the gas appliance pressure regulator shall be installed to the outdoors in accordance
with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1, Natural Gas
Installation Code, CAN/CGA-B149.1, or the Propane Installation Code CAN/CGA-B149.2, as applicable.

An adequate gas supply is imperative. Undersized or low pressure lines will restrict the volume of gas required for
satisfactory performance. A 1/8" pressure tap is located on the manifold to measure the manifold pressure. The
supply line to the sectional range should be no smaller than the inside diameter of the pipe on the se ctional range to
which it is connected.

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 5 OF 76

SPECIFICATIONS CHEF SERIES SECTIONAL RANGE

Figure 2

Dimensions

36" Flue Riser

12"

(305)

24"

(610)

9" (229)

33-3/4"

37-3/4"

(959)

(859)

Front Gas

Manifold

15-3/4"

(400)

37-3/4" (959)

34" (864)

4-1/2" (114)

SIDE VIEW

24" (610)

43-3/4" (1111)

40" (1016)

Motor for

Convection

Oven Model

Flue riser for “deep” depth-option extends rearward 6"
(cooking suface area is same as for “standard” depth).

8-1/2" (216)

SIDE VIEW of Modular Model

39-3/4"

(1010)

36" (914)

48" (1219)

24" Flue Riser

5" Flue Riser

36"

(914)

Optional

Rear Gas

Connection

6" (152)

41"

(1041)

20"

(508)

60"

(1524)

72"

(1829)

7" (178)

7" (178)

2-1/2" (64)

Electrical

Connection

for Oven

Models

18"

(457)

7" (178)

2-1/2" (64)

PAGE 6 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE SPECIFICATIONS

UTILITY REQUIREMENTS AND CRATED WEIGHT

Model Width Base Type Top Type

LGR12C-B 12" cabinet flush 35K open-burner 70,000 60,000 - - 225 (102)
LGR12C-G 12" cabinet standard griddle 32,000 28,000 - - 225 (102)
LGR12C-H 12" cabinet uniform hot top 32,000 28,000 - - 180 (82)
LGR12N-B 12" modular flush 35K open-burner 70,000 60,000 - - 175 (79)
LGR12N-G 12" modular standard griddle 32,000 28,000 - - 175 (79)
LGR12N-H 12" modular uniform hot top 32,000 28,000 - - 130 (59)
LGR24C-BB 24" cabinet flush 35K open-burner 140,000 120,000 - - 480 (218)
LGR24C-BB-SU 24" cabinet step-up 35K open-burner 140,000 120,000 - - 480 (218)
LGR24C-CC 24" cabinet charbroiler 64,000 56,000 - - 360 (163)
LGR24C-GG 24" cabinet standard griddle 64,000 56,000 - - 300 (136)
LGR24C-HH 24" cabinet uniform hot top 64,000 56,000 - - 280 (127)
LGR24C-TT 24" cabinet thermostatic griddle 64,000 56,000 - - 300 (136)
LGR24N-BB 24" modular flush 35K open-burner 140,000 120,000 - - 395 (179)
LGR24N-BB-SU 24" modular step-up 35K open-burner 140,000 120,000 - - 395 (179)
LGR24N-CC 24" modular charbroiler 64,000 56,000 - - 360 (163)
LGR24N-GG 24" modular standard griddle 64,000 56,000 - - 300 (136)
LGR24N-HH 24" modular uniform hot top 64,000 56,000 - - 205 (93)
LGR24N-TT 24" modular thermostatic griddle 64,000 56,000 - - 300 (136)
LGR36A-BBB 36" convection oven flush 35K open-burner 255,000 222, 000 3.8 1.6 740 (336)
LGR36A-BBB-SU 36" convection oven step-up 35K open-burner 255,000 222,000 3.8 1.6 740 (336)
LGR36A-CCC 36" convection oven charbroiler 141,000 126,000 3.8 1.6 775 (352)
LGR36A-GGG 36" convection oven standard griddle 141,000 126,000 3.8 1.6 840 (381)
LGR36A-GRAD 36" convection oven graduated hot-top 107,000 87,000 3.8 1.6 760 (345)
LGR36A-HHH 36" convection oven uniform hot top 141,000 126,000 3.8 1.6 720 (327)
LGR36A-TTT 36" convection oven thermostatic griddle 141,000 126,000 3.8 1.6 840 (381)
LGR36A-XX 36" convection oven flush 45K open-burner 225,000 222,000 3.8 1.6 740 (336)
LGR36C-BBB 36" cabinet flush 35K open-burner 210,000 180,000 - - 490 (222)
LGR36C-BBB-SU 36" cabinet step-up 35K open-burner 210,000 180,000 - - 490 (222)
LGR36C-CCC 36" cabinet charbroiler 96,000 84,000 - - 620 (281)
LGR36C-GGG 36" cabinet standard griddle 96,000 84,000 - - 590 (268)
LGR36C-GRAD 36" cabinet graduated hot-top 62,000 45,000 - - 510 (231)
LGR36C-HHH 36" cabinet uniform hot top 96,000 84,000 - - 470 (213)
LGR36C-TTT 36" cabinet thermostatic griddle 96,000 84,000 - - 590 (268)
LGR36C-XX 36" cabinet flush 45K open-burner 180,000 177,000 - - 490 (222)
LGR36D-BBB 36" standard oven flush 35K open-burner 255,000 222,000 0* 0* 690 (313)
LGR36D-BBB-SU 36" standard oven step-up 35K open-burner 255,000 222,000 0* 0* 690 (313)
LGR36D-CCC 36" standard oven charbroiler 141,000 126,000 0* 0* 750 (340)
LGR36D-GGG 36" standard oven standard griddle 141,000 126,000 0* 0* 790 (358)
LGR36D-GRAD 36" standard oven graduated hot-top 107,000 87,000 0* 0* 710 (322)
LGR36D-HHH 36" standard oven uniform hot top 141,000 126,000 0* 0* 670 (304)
LGR36D-TTT 36" standard oven thermostatic griddle 141,000 126,000 0* 0* 790 (358)
LGR36D-XX 36" standard oven flush 45K open-burner 225,000 222,000 0* 0* 690 (313)
LGR36N-BBB 36" modular flush 35K open-burner 210,000 180,000 - - 450 (204)
LGR36N-BBB-SU 36" modular step-up 35K open-burner 210,000 180,000 - - 450 (204)
LGR36N-CCC 36" modular charbroiler 96,000 84,000 - - 350 (159)
LGR36N-GGG 36" modular standard griddle 96,000 84,000 - - 530 (240)
LGR36N-GRAD 36" modular graduated hot-top 62,000 45,000 - - 450 (204)
LGR36N-HHH 36" modular uniform hot top 96,000 84,000 - - 410 186)
LGR36N-TTT 36" modular thermostatic griddle 96,000 84,000 - - 530 (240)
LGR36N-XX 36" modular flush 45K open-burner 180,000 177,000 - - 450 (204)
LGR48A-CCCC 48" convection oven charbroiler 173,000 154,000 3.8 1.6 621(281)
LGR48A-GGGG 48" convection oven standard griddle 173,000 154,000 3.8 1.6 729 (330)
LGR48A-TTTT 48" convection oven thermostatic griddle 173,000 154,000 3.8 1.6 729 (330)
LGR48C-CCCC 48" cabinet charbroiler 128,000 112,000 - - 462 (209)
LGR48C-GGGG 48" cabinet standard griddle 128,000 112,000 - - 480 (217)
LGR48C-TTTT 48" cabinet thermostatic griddle 128,000 112,000 - - 480 (217)
LGR48D-CCCC 48" standard oven charbroiler 173,000 154,000 0* 0* 568 (257)
LGR48D-GGGG 48" standard oven standard griddle 173,000 154,000 0* 0* 676 (306)
LGR48D-TTTT 48" standard oven thermostatic griddle 173,000 154,000 0* 0* 676 (306)
LGR48N-CCCC 48" modular charbroiler 128,000 112,000 - - 276 (125)
LGR48N-GGGG 48" modular standard griddle 128,000 112,000 - - 395 (179)
LGR48N-TTTT 48" modular thermostatic griddle 128,000 112,000 - - 395 (179)

Natural Gas

(BTU/hour)

GAS ELECTRICITY

Propane

(BTU/hour)

120V

(amps)

208/240V

(amps)

* Standing Oven Pilot Models

Crated Weight

pounds (kg)

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 7 OF 76

SPECIFICATIONS CHEF SERIES SECTIONAL RANGE

ELECTRICITY SUPPLY

Units with convection-oven bases with optional electronic ignition require electric po wer (50Hz or 60Hz single-phase
AC). 120V models have a 7-foot (2134 mm) power cord with a grounded plug (1.0 amps for “D” Models and 4.8 amps
for “A” Models). The 208/240V models have a terminal block for connection to a single-phase 208/24 0V source (1.0
amps for “D” Models and 2.6 amps for the “A” Models).

The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of
local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as
applicable. An electrical diagram is located on the rear of the range, near the motor.

PAGE 8 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE OPERATION

OPERATION

DANGER

EXPLOSION HAZARD

In the event a gas odor is detected, shut down equipment at the main shut off valve. Immediately call the
emergency phone number of your gas supplier.

CAUTION

If a pilot flame pilot should go out, the flow of gas to the corresponding burner is NOT interrupted. Consequently, it
is the responsibility of the operator to check the ignition of each burner immediately EVERY TIME a burner is
turned on. Should ignition fail after 10 seconds, turn off the burner, wait 5 minutes, and then try again.

LIGHTING AFTER GAS HAS BEEN SHUT OFF

When turning on the main gas supply to a sectional range, do the following:

1. Make sure that all the control knobs and power switches of all the connected appliances are in the OFF position.

2. Turn on the gas-supply shut-off valve(s).

3. Light the standing pilots of each connected appliance.

4. Light the ovens of the sectional range first, then wait six minutes before turning on the top sections. This enables
all air to be purged from the sectional-range gas piping.

SHUTDOWN OF ENTIRE RANGE

To place the range in a standby state (ready for use), Oven bases with the electronic ignition option, turn all burner
control knobs to OFF, set all thermostats to their lowest position, and switch all ovens OFF. The pilots will remain lit.
On the standing pilot units, same as above except turn thermostat knob to the “OFF” position. The pilots will remain
lit.

To completely shut down the range for an extended period (or prior to disconnecting the gas supply), place the range
in a standby state (as described in the previous paragraph), then turn OFF the manual shut -off valves of all gas
supply connections. This will extinguish the pilots.

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 9 OF 76

OPERATION CHEF SERIES SECTIONAL RANGE

Figure 3

Operation of Open-Burner Sections

Each 12"-wide section has two control knobs. The left knob
controls the rear burner, while the right knob controls the
front burner. Each knob can be turned to OFF or to any
position in the range from LOW to HIGH.

To start cooking, turn the appropriate control knob to HIGH.
Visually check that the burner ignites. The gas does NOT
automatically shut off if the burner does not ignite! If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

While cooking, do not allow excessive drippings and/or
debris to accumulate on or below the burners. When
necessary, pull out and clean the drippings tray.

Burner Grate

(lifts out for cleaning)

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each burner has a pilot located beside the burner. To light a
pilot, do the following:

1. Check that the burner control knob is in the OFF position.

2. Check that the pilot is in the correct position beside the
burner.

3. Turn on the gas supply to the sectional range (if not
already on).

4. Light the pilot with a match or a pilot-lighting device. The
pilot flame should be blue and steady.

Rear-Burner

Control Knob

(OFF, HIGH-to-LOW)

Front-Burner

Control Knob

(OFF, HIGH-to-LOW)

Drippings Tray

(slides out for cleaning)

PAGE 10 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE OPERATION

Figure 4

Operation of Uniform Hot-Top Section

Each 12”-wide section has one control knob, which can be
turned to OFF or to any position in the range from LOW to
HIGH. When the control is set to HIGH, the hot top surface
will heat to about 700°F (370°C).

To start cooking, turn the appropriate control knob to HIGH.
Visually check that the burner ignites.

automatically shut off if the burner does not ignite!

The gas does NOT

If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Do not waste gas and abuse equipment by leaving the
burner on HIGH all the time.

certain electronic components may occur, and

YOUR WARRANTY

. During idle periods, turn the control to

Damage to the plates and

MAY VOID

LOW to keep the top warm.

Uniform HotTop Plate

(lifts out for cleaning

and lighting pilot)

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each 12”-wide section has two burners, each of which has a
pilot located near the front of the burner. To light the pilots,
do the following:

1. Check that the control knob is in the OFF position.

2. Lift up a hot-top section plate in order to expose the two
pilots.

3. Check that each pilot is in the correct position.

4. Turn on the gas supply to the sectional range (if not
already on).

5. Light the pilots with a match or a pilot-lighting device. The
pilot flames should be blue and steady.

Burner Control Knob

(OFF, HIGH-to-LOW)

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 11 OF 76

OPERATION CHEF SERIES SECTIONAL RANGE

Figure 5

Operation of Graduated Hot-Top Section

Each section has one control knob, which can be turned to
OFF or to any position in the range from LOW to HIGH.
When the control is set to HIGH, the round center section will
heat to about 725°F (385°C), the ring-shaped section will
heat to about 625°F (330°C), and the outer areas will heat to
about 500°F (260°C).

To start cooking, turn the control knob to HIGH. Visually
check that the burner ignites.

automatically shut off if the burner does not ignite!

The gas does NOT

If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Do not waste gas and abuse equipment by leaving the
burner on HIGH all the time.

certain electronic components may occur, and

YOUR WARRANTY

. During idle periods, turn the control to

Damage to the plates and

MAY VOID

LOW to keep the top warm.

When done cooking, turn the control knob to OFF. (The pilot
should remain lit).

Each section has one burner. The pilot is located adjacent to
the burner. To light the pilot, do the following:

1. Check that the control knob is in the OFF position.

2. Lift out the round center plate in order to expose the pilot.

3. Check that the pilot is in the correct position.

4. Turn on the gas supply to the sectional range (if not
already on).

5. Light the pilot with a match or a pilot-lighting device. The
pilot flame should be blue and steady.

Medium TemperatureArea
(plate lifts out for cleaning)

Lower Temperature Area

(plate lifts out for cleaning)

HighTemperature Area

(plate lifts out for cleaning

and lighting pilot)

Lower TemperatureArea

(plate lifts out for cleaning)

Burner Control Knob

(OFF, HIGH-to-LOW)

PAGE 12 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE OPERATION

Figure 6

Operation of Charbroiler Section

Each 12”-wide section has one control knob, which can be
turned to OFF, HIGH, or LOW. Each burner top-grate can be
turned over to provide either wide branding marks or
narrower branding marks with channels to carry away
drippings (and so reduce flare up). The back-to-front slope of
each top-grate is adjusted by positioning the back end of the
top-grate on either the lower or the higher grate-support rail.
The radiants (just above the burners) can be reversed front­and-back to provide higher heat toward the back than the
front, or vice versa. “Lava rock” briquettes can be placed on
grates located above the radiants.

To start cooking, turn the appropriate control knob to HIGH.
Visually check that the burner ignites.

automatically shut off if the burner does not ignite!

The gas does NOT

If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Grates

(lift out for cleaning)

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each 12”-wide section has two burners, each of which has a
pilot located near the front of the burner. To light the pilots,
do the following:

1. Check that the burner control knob is in the OFF position.

2. Lift up a grate in order to expose the two pilots. They are
accessible through a slot near the front end of the radiant
plate.

3. Check that each pilot is in the correct position.

4. Turn on the gas supply to the sectional range (if not
already on).

5. Light the pilots with a match or a pilot-lighting device. The
pilot flames should be blue and steady.

Burner Control Knob

(OFF, HIGH, or LOW)

Drippings Tray

(slides out for cleaning)

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 13 OF 76

OPERATION CHEF SERIES SECTIONAL RANGE

Figure 7

Operation of Standard (Non-Thermostatic) Griddle Sections

Each 12”-wide section has one control knob, which can be
turned to OFF, HIGH, or LOW.

To start cooking, turn the appropriate control knob to HIGH.
Check that the burner ignites.

automatically shut off if the burner does not ignite!

The gas does NOT

If the
burner does not ignite, check and/or light the pilots (see
procedure at right). When the burner is hot, the burner flame
should appear blue and steady (some slight yellowing of the
flame tips may occur when using propane gas).

Always remember to heat the griddle slowly because quick
heating may cause costly damage. Never place utensils on
the griddle.

Do not waste gas and abuse equipment by leaving the
griddle on HIGH all the time.

certain electronic components may occur, and

YOUR WARRANTY

. During idle periods, turn the control to

Damage to the griddle and

MAY VOID

LOW to keep the griddle warm. (Do not allow the griddle to

overheat above 550°F (288°C), as this will cause warping or
breakage.)

When necessary while cooking, pull out and empty the
grease drawer.

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each griddle section has a single pilot that is lit using a long
match inserted thorough a hole in the front valve panel. (A
48"-wide griddle has two pilots.) To light the pilot, do the
following:

1. Check that all the control knobs are in the OFF position.

2. Turn on the gas supply to the sectional range (if not
already on).

3. Light the pilot by inserting a long match (at least 11" long)
or pilot-lighting device straight into the hole on the front
valve panel of the griddle.

Burner Control Knob

(OFF, HIGH, or LOW)

Grease Drawer

(slides out for cleaning)

Pilot-Lighting

Opening

PAGE 14 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE OPERATION

Figure 8

Operation of Thermostatic Griddle Sections

Each 12”-wide section has one control knob that can be
turned to OFF, or to any temperature in the range 150°F to
400°F (66°C to 204°C).

To start cooking, turn on the appropriate control knob. Check
that the burner ignites. If the burner does not ignite, check
and/or light the pilots (see procedure at right).

Never place utensils on the griddle.

Do not waste gas and abuse equipment by leaving the
griddle set at a high temperature all the time.

Damage to
the griddle and certain electronic components may occur,
and

MAY VOID YOUR WARRANTY. During idle periods,

turn the control to a low temperature to keep the griddle
warm. (Do not allow the griddle to overheat above 550°F
(288°C), as this will cause warping or breakage.)

When necessary while cooking, pull out and empty the
grease drawer.

When done cooking, turn the appropriate control knob to
OFF. (The pilot should remain lit).

Each griddle section has a single pilot that is lit using a long
match inserted thorough a hole in the front valve panel. (A
48"-wide griddle has two pilots.) To light the pilot, do the
following:

1. Check that all control knobs are in the OFF position.

2. Turn on the gas supply to the sectional range (if not
already on).

3. Turn on the Griddle Gas Shut-Off Valve (if not already
on).

4. Press and hold in the Safety Switch Button.

5. Light the pilot by inserting a long match (at least 11" long)
or pilot-lighting device straight into the hole on the front
valve panel of the griddle.

6. After about a minute, release the Safety Switch Button.
The pilot should remain lit.

Safety
Switch
Button

Burner Control Knob

(OFF, temperature)

Griddle Gas

Shut-Off Valve

Grease Drawer

(slides out for cleaning)

Pilot-Lighting

Opening

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 15 OF 76

OPERATION CHEF SERIES SECTIONAL RANGE

Figure 9

Operation of Oven

Each oven has a thermostatic control that can be set in the
range 175°F to 550°F (66°C to 260°C). Convection ovens
have a fan that can be set to HI speed or LO speed.

While cooking, if the door is opened on a convection oven,
the fan and heat will temporarily stop until the door is closed.

Do not allow excessive drippings and/or debris to
accumulate on the interior of the oven. When necessary, pull
out and clean the oven-bottom tray.

To light and start cooking, do the following:
FOR UNITS WITH A STANDING PILOT

1. Open kick panel and locate knob on valve assembly.

2. Turn the knob to PILOT and press inward. While holding
the knob inward, light the pilot with an appropriate lighter.

3. Hold knob in the inward position for 30 seconds and
release. The pilot should remain lit.

4. Turn the knob to ON and close kick panel.

5. Select on the thermostat the cooking temperature
appropriate for the food to be cooked.

6. For convection ovens, select the fan speed appropriate
for the food to be cooked.

FOR UNITS WITH ELECTRONIC IGNITION

1. Set the Oven Power Switch to ON. The pilot will light
automatically. (You will hear a “snapping” sound until the
pilot ignites.)

2. Select on the thermostat the cooking temperature
appropriate for the food to be cooked.

3. For convection ovens, select the fan speed appropriate
for the food to be cooked.

When done cooking, turn the Oven Power Switch to OFF.

Controls for Ovens
with Standing Pilot

Oven Power Switch

Fan-Speed Switch

(for Convection Ovens)

Oven Thermostat

Controls for Ovens

with Electronic Ignition

WARNING

PILOT-ON Knob

THE USE OF ALUMINUM FOIL CAN CAUSE HEAT DISTRIBUTION PROBLEMS IN OVENS. EXTREME
CARE MUST BE USED WHEN PLACING ALUMINUM FOIL IN THE OVEN TO ENSURE THAT IT DOES NOT
BLOCK OR CHANGE THE AIR FLOW. THE USE OF ALUMINUM FOIL MAY VOID THE PRODUCT
WARRANTY IF ITS USE IS ASCERTAINED TO BE A PROBLEM.

PAGE 16 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE CLEANING & MAINTENANCE

CLEANING & MAINTENANCE

WARNING

Shut off the gas supply to the appliance before cleaning or performing maintenance on any gas appliance.
The appliance may be equipped with a restraint device to limit its movement in order to prevent damage to the

gas connection. If disconnection of this restraint is necessary to move the appliance for cleaning or
maintenance, reconnect the restraint when the appliance is moved back to its original installed position.

Lang appliances are sturdily constructed of the best materials and are designed to provide du rable service when
treated with ordinary care. To expect the best performance, your equipment must be maintained in good condition and
cleaned daily. Naturally, the periods for this care and cleaning depend on the amount and degree of usag e.

Following daily and periodic maintenance procedures will enhance long life for your equipm ent. Climatic conditions
(such as salt air) may require more thorough and frequent cleaning or the life of the equi pment could be adversely
affected.

Keep exposed, cleanable areas clean at all times.

DAILY CLEANING AND MAINTENANCE

The daily cleaning procedure is as follows:

1. Shut off the main gas supply and allow the sectional range to cool.

2. Pull out, empty, and clean all drippings trays and grease drawers.

3. Remove and clean all oven racks and oven-bottom trays. Wipe clean the interior of the oven.

4. Visually check for any food and/or debris that may have fallen down into the burner areas.

5. Wipe clean all exterior surfaces.

6. Replace the cleaned and dried drippings trays, grease drawers, and oven components.

7. Check that nothing has been left on or near the sectional range that might block the entry of combustion air or
the escape of combustion exhaust.

MONTHLY CLEANING AND MAINTENANCE

The following tasks should be performed monthly:

1. Clean around burner air mixers and orifices if lint has accumulated in these areas.

2. Check for proper pilot operation. Check that the pilot flames are blue (with little or no yellow in the flame tips),
stable (not lifting off the pilots), and not producing carbon. If adjustment is necessary, call for service.

3. Check for proper burner operation. The burner flames should be blue and stable. If adjustment is necessary, call
for service.

SEMIANNUAL CLEANING AND MAINTENANCE

At least twice a year the venting system should be examined and cleaned.

STAINLESS-STEEL SURFACES

To remove normal dirt, grease and product residue from stainless steel surfaces that operate at LOW temperature,
use ordinary soap and water (with or without detergent) applied with a sponge or cloth. Dry thoroughly with a clean
cloth.

To remove BAKED-ON grease and food splatter, or condensed vapors; apply cleanser to a damp cloth or sponge and
rub cleanser on the metal in the direction of the polishing lines on the metal. Rubbing cleanser, as gently as possible,
in the direction of the polished lines will not mar the finish of the stainless steel. NEVER RUB WITH A CIRCULAR
MOTION. Soil and burnt deposits which do not respond to the above procedure can usually be removed by rubbing
the surface with SCOTCH-BRITE scouring pads or STAINLESS scouring pads. DO NOT USE ORDINARY STEEL

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 17 OF 76

CLEANING & MAINTENANCE CHEF SERIES SECTIONAL RANGE

WOOL as any particles left on the surface will rust and further spoil the appearance of the finish. NEVER USE A
WIRE BRUSH, STEEL SCOURING PADS (EXCEPT STAINLESS), SCRAPER, FILE OR OTHER STEEL TOOLS.
Surfaces which are marred collect dirt more rapidly and become more difficult to clean. Marring also increases the
possibility of corrosive attack. Refinishing may then be required.

“Heat tint” is darkened areas that sometimes appear on stainless steel surfaces where the area has been subjected to
excessive heat. These darkened areas are caused by thickening of the protectiv e surfa ce of t he stainless steel and
are not harmful. Heat tint can normally be removed by the foregoing, but tint which does not respond to this procedure
calls for a vigorous scouring in the direction of the polish lines using SCOTCH-BRITE scouring pads or a STAINLESS
scouring pad in combination with a powered cleanser. Heat tint may be lessened by reducing heat to equipment
during slack periods.

BAKED-ENAMEL SURFACES

Allow appliance to cool somewhat after use and wash baked-enamel surfaces with a hot, mild detergent or soap
solution. In particular, clean off all grease deposits. Dry thoroughly with a dry cloth.

OPEN-BURNERS AND GRATES

The grates can be removed and cleaned with a solution of hot water and strong soap or detergent. The burners
themselves require little attention, but if spillage should occur, it may be necessary to clean around pilot areas, air
mixer and under burners. Use a wire brush if necessary. Periodically, open-burners sho uld be removed and cleaned.
Allow the interior of the burner to drain, and dry thoroughly before replacing.

HOT-TOP SURFACES

Before cleaning hot-top surfaces, allow them to cool. If water is used on hot-tops while they are still hot, they may
crack, so avoid this practice. The hot-top plates can be removed and cleaned with hot water and detergent. A wire
brush may be used on the underside of the hot top plate. It is recommended not to clean tops while still on the range,
even if cooled, as excess water will drip into the burner box and deteriorate the metal.

CARE OF GRIDDLES

A griddle should be carefully cared for in order to avoid possible damage. (The griddle should have been tempered as
part of the installation procedure, see page
any type of steel wool. Small particles may be left on the surface and get into food products. Do not clean spatula by
hitting the edge on the griddle plate. Such action will only cut and pit the griddle plate, leaving it rough and hard to
clean.

27). Use a Norton Alundum Griddle Brick to clean the griddle. Do not use

OVEN INTERIOR

WARNING

FOR YOUR SAFETY, DISCONNECT THE POWER SUPPLY TO THE SECTIONAL RANGE BEFORE
CLEANING THE OVEN. WHEN CLEANING THE BLOWER WHEEL OF A CONVECTION OVEN, BE SURE TO
HAVE THE POWER SWITCH IN THE “OFF” POSITION.

To clean the oven interior, first allow the oven to cool. Remove oven bottom and clean it by rubbing with strong
detergent and a Brillo pad or similar scrubber. “Spillovers” should be cleaned from the bottom as soon as possible to
prevent carbonizing and a “burnt-on” condition. For stubborn accumulations, commercial oven clea ners are
recommended.

The porcelain oven door lining can be cleaned in a similar manner. The side, rear and top lining should be wiped only
with a cloth dampened with a mild detergent and water. Avoid using excessive amounts of water, as this may drip into
burner compartment and deteriorate the metal in that area. Do not use strong commercial cleaners or abrasive pads
on the side, rear or top linings, as they may damage the finish or leave gray residue.

PAGE 18 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE INSTALLATION

INSTALLATION

NOTICE

These installation procedures must be followed by qualified personnel or warranty will be void.
Local codes regarding installation vary greatly from one area to another. The National Fire Protection Association,

Inc., states in its NFPA 96 latest edition that local codes are the “authority having jurisdiction” when it comes to
installation requirements for equipment. Therefore, installations should comply with all local codes.

The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1, Natural Gas Installation Code, CAN/CGA-B149.1, or the Propane Installation Code CAN/CGA-
B149.2, as applicable, including:

1. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psi (3.45 kPa).

2. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.45
kPa).

NOTICE

EXHAUST FANS AND CANOPIES: It is recommended that the range be installed under a ventilation hood.

Consult local codes for proper installation of hoods. Proper ventilation is the owner’s responsibility. Any problem
due to improper ventilation will not be covered by warranty.

NOTICE

In the Commonwealth of Massachusetts all gas appliances vented by either mechanical systems or ventilation
hoods shall comply with 248 CMR interlocking requirements.

This installation procedure does NOT cover sectional fryers, fryer filter systems, salamander b roile rs, upright broilers,
cheese melters, or refrigerated bases. Consult the manuals of those appliances when they are being installed as part
of a sectional range battery.

STEP 1: UNPACKING

IMMEDIATELY INSPECT FOR SHIPPING DAMAGE

All containers should be examined for damage before and during unloading. The freight carrier has assumed
responsibility for its safe transit and delivery. If damaged equipment is received, either apparent or concealed, a
claim must be made with the delivering carrier.

Apparent damage or loss must be noted on the freight bill at the time of delivery. The freight bill must then be
signed by the carrier representative (Driver). If the bill is not signed, the carrier may refuse the claim. The carrier
can supply the necessary forms.

A request for inspection must be made to the carrier within 15 days if there is concealed damage or loss that is not
apparent until after the equipment is uncrated. The carrier should arrange an inspection. Be certain to hold all
contents plus all packing material.

For each section, do the following:

1. Cut the banding straps and remove the corrugated cardboard surrounding the section. (If legs, casters, a flue
riser, and/or shelf components were shipped in the same container, set them aside for installation in later steps
of this procedure. Do not remove any tags or labels attached to the range until the range is installed and working
properly.

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 19 OF 76

INSTALLATION CHEF SERIES SECTIONAL RANGE

2. Cut the banding strap holding the range to the wooden skid.

3. Unbolt the shipping hold-down brackets from the skid, then remove the brackets from the appliance (see

Figure

10).

4. If the range is to be installed on 6" legs, go to Step 2a.
If the range is to be installed on 6" casters, go to Step 2b.
If the range is to be installed on a caster-frame, go to Step 2c.

Figure 10

Removal of Shipping Hold-Down Brackets

Shipping
Hold-Down
Brackets

STEP 2A: ATTACH LEGS TO THE RANGE

A set of four legs is packed with units ordered with legs. (For units ordered with casters, go to Step 2b.)
A threaded leg pad is fastened to the base frame at each corner. Each leg has a correspondin g mating thread. The

legs can be adjusted to overcome a slightly uneven floor.

1. Raise the range sufficiently to allow the legs to be attached. For safety, “shore up” and support the range with an
adequate blocking arrangement strong enough to support the load.

2. Screw the legs into the holes in the centers of the leg pads (see

3. Lower the range gently onto a level surface. Never drop or allow the range to fall.

4. Go on to Installation Step 4.

Figure 11).

PAGE 20 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE INSTALLATION

Figure 11

Installation of Legs

STEP 2B: ATTACH CASTERS TO THE RANGE

NOTICE

For an appliance equipped with casters, (1) the installation shall be made with a connector that complies with the

Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas Appliances,
CAN/CGA-6.16, and a quick-disconnect device that complies with the Standard for Quick-Disconnect Devices for
Use With Gas Fuel, ANSI Z21.41, or Quick Disconnect Devices for Use with Gas Fuel, CAN1-6.9, (2) adequate

means must be provided to limit the movement of the appliance without depending on the connector and the
quick-disconnect device or its associated piping to limit the appliance movement and (3) the restraining means
should be attached to a frame member on the back of the unit.

A set of four casters is packed with units ordered with casters (instead of legs).
A threaded leg pad is fastened to the base frame at each corner. Each caster has a corresponding mating thread. The

casters can be adjusted to overcome a slightly uneven floor. Casters are provided with a fitting for proper lubrication
when required.

1. Raise unit sufficiently to allow the casters to be attached. For safety, “shore up” and support the range with an
adequate blocking arrangement strong enough to support the load.

2. Screw the casters into the holes in the centers of the leg pads (see
locking brake under the front of the range.

3. Lower the range gently onto a level surface. Never drop or allow the range to fall.

4. Go to Installation Step 3.

Figure 12). Install the casters that have a

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 21 OF 76

INSTALLATION CHEF SERIES SECTIONAL RANGE

Figure 12

Installation of Casters

1

STEP 2C: MOUNT RANGE ON CASTER FRAME

NOTICE

For an appliance equipped with casters, (1) the installation shall be made with a connector that complies with the

Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas Appliances,
CAN/CGA-6.16, and a quick-disconnect device that complies with the Standard for Quick-Disconnect Devices for
Use With Gas Fuel, ANSI Z21.41, or Quick Disconnect Devices for Use with Gas Fuel, CAN1-6.9, (2) adequate

means must be provided to limit the movement of the appliance without depending on the connector and the
quick-disconnect device or its associated piping to limit the appliance movement and (3) the restraining means
should be attached to a frame member on the back of the unit.

The range can be mounted on an optional caster frame. The frame will have a threaded leg pad at each corner. Each
caster has a corresponding mating thread. The casters can be adjusted to overcome a slightly uneven floor. Casters
are provided with a fitting for proper lubrication when required.

1. Assemble the caster frame components.

2. Screw the casters into the holes in the centers of the leg pads of the caster frame. Install the casters that have a
locking brake under the front of the battery.

3. Lower the caster frame gently onto a level surface. Never drop or allow the frame to fall.

4. Block and brace the frame so that it will not move while the battery sections are installed on it.

5. Lift and gently place the range in position on the caster frame. Never drop or allow the range to fall.

6. Bolt the range to the caster frame.

7. Go to Installation Step 3.

PAGE 22 OF 76 OWNER’S MANUAL 1192040 REV 1 (01/10)

CHEF SERIES SECTIONAL RANGE INSTALLATION

STEP 3: ATTACH RESTRAINT TO RANGE (OR BATTERY) MOUNTED ON CASTERS

NOTICE

For an appliance equipped with casters, (1) the installation shall be made with a connector that complies with the

Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas Appliances,
CAN/CGA-6.16, and a quick-disconnect device that complies with the Standard for Quick-Disconnect Devices for
Use With Gas Fuel, ANSI Z21.41, or Quick Disconnect Devices for Use with Gas Fuel, CAN1-6.9, (2) adequate

means must be provided to limit the movement of the appliance without depending on the connector and the
quick-disconnect device or its associated piping to limit the appliance movement and (3) the restraining means
should be attached to a frame member on the back of the unit.

Install the restraint cable to a range (or battery) mounted on casters using the following procedure:

1. Secure the restraining-device bracket (item “B” in
appliance connector inlet and outlet connections. Use four #12 screws (items “C”) and plastic anchors (items “A”)
if necessary.

2. Install eye-bolt (item “F”) to a frame member on the rear of the equipment. After checking carefully behind the
frame member for adequate clearance, drill a 1/4" hole through the frame member.

3. Thread hex nut (item “G”) and slide the washer (item “H”) onto the eye-bolt. Insert the eye-bolt through the 1/4"
drilled hole and secure with a washer (item “H”) and nylon lock nut (item “I”).

4. Using the spring-loaded snap hooks, attach the restraining device to the bracket and the eye-bolt.

5. Using the cable clamp (item “D”), adjust the restraining device extended length to prevent over-bending or
kinking of the appliance connector.

For units not equipped with flame safety devices, be sure all valves are turned off prior to disconnecting. After
reconnecting, be sure all control knobs are turned off and all pilots are lit.

Figure 13) to a wall stud located as close as possible to the

NOTICE

Adequate means must be provided to limit the movement of the appliance without depending on the connector and
the quick-disconnect device or its associated piping to limit the appliance movement.

The restraining means should be attached to a frame member on the back of the unit.

OWNER’S MANUAL 1192040 REV 1 (01/10) PAGE 23 OF 76