Lang Manufacturing CCSE12A-208 Installation Manual
ELECTRIC CLAMSHELL
®
CSE12-208VCD, CSE12A-1, CSE12A-2
Glass Surface
CSE12A-1G thru CSE12A-6G
Contact Clam
CCSE12A-208
Installation and
Operation
Instructions
2M-W363 Rev. F 3/19/2015
CSE12A
SAFETY SYMBOL
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN
INSTRUCTIONS TO BE FOLLOWED IN THE EVENT USER SMELLS GAS. THIS
INFORMATION SHALL BE OBTAINED BY CONSULTING YOUR LOCAL GAS SUPPLIER.
AS A MINIMUM, TURN OFF THE GAS AND CALL YOUR GAS COMPANY AND YOUR
AUTHORIZED SERVICE AGENT. EVACUATE ALL PERSONNEL FROM THE AREA.
IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE
CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION,
OPERATION & MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR
WARNING, TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE
CONTROL PANEL. NO USER-SERVICABLE PARTS INSIDE.
REPAIRS SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.
FOR YOUR SAFTEY
THE VICINTIY OF THIS OR ANY OTHER APPLIANCE.
POST IN PROMINENT LOCATION
WARNING
SERVICING THIS EQUIPMENT.
WARNING
RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN
NOTICE
Using any part other than genuine Lang factory supplied parts relieves the manufacturer of all
liability.
Lang reserves the right to change specications and product design without notice. Such
revisions do not entitle the buyer to corresponding changes, improvements, additions or
replacements for previously purchased equipment.
Due to periodic changes in designs, methods, procedures, policies and regulations,
the specications contained in this sheet are subject to change without notice. While
Lang exercises good faith efforts to provide information that is accurate, we are not
responsible for errors or omissions in information provided or conclusions reached as a
result of using the specications. By using the information provided, the user assumes all risks
in connection with such use.
MAINTENANCE AND REPAIRS
Contact your local dealer for service or required maintenance. Please record the model number, serial
number, voltage and purchase & Installation Information in the area below and have it ready when you
call to ensure a faster service.
Model No.:
Serial No.:
Voltage:
Purchased From:
Location:
Purchase
Date:
2M-W363: Electric Clamshell® CSE12A
1-Phase
or 3 Phase:
Installed Date:
2
PROBLEMS, QUESTIONS or CONCERNS
Before you proceed consult you authorized Lang service agent directory
or
Call the Lang Technical Service & Parts Department at 314-678-6315
TABLE OF CONTENTS
Saftey Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Information
Lockout Procedures . . . . . . . . . . . . . . . . . . . . . . . . 4
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Technical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Receiving the unit . . . . . . . . . . . . . . . . . . . . . . . . . 5
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Un-crating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . 6
Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cleaning
Daily . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Weekly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Crome Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hood Stop Adjustments . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating Instructions CONTACT CLAM ONLY . . . . . . . . . . . . 10
Exploded View & Parts List
CSE12-208VCD, CSE12A-1, CSE12A-2 . . . . . . . . . . . . 12-13
2M-W363: Electric Clamshell® CSE12A
CSE12A-1G thru 6G (glass surface) . . . . . . . . . . . . . . 14-15
CSE12-CC208 (contact clam) . . . . . . . . . . . . . . . . . . 16-18
Wiring Diagram
CCSE12A1 (contact clam) . . . . . . . . . . . . . . . . . . . .19
CSE12A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
NOTICE Service on this or any other Lang appliance must be performed by
qualied personnel only. Consult your Lang Authorized Service Agent
Directory. You can call our service number 314-678-6315 or visit our
website www.langworld.com for the service agent nearest you.
3
Safety Precautions
Lang manufacturing, hereby disclaims any and all responsibility for injury, damage, loss or other claim that may occur
to person or property from improper alteration, modication, addition, operation, maintenance or service, whether it be
mechanical, electrical, or otherwise, which may occur from such improper alteration, modication, addition, operation,
maintenance or service to this piece of equipment.
Safety Considerations
Your 12-inch Clamshell® is manufactured to rigid standards. This equipment is approved by a certifying agency to
conform to safety and sanitation standards.
The presence of safety equipment control and interlocks on an appliance and attendant components of installation
cannot in and of themselves, assure absolute safety of operation. Diligent, capable, well-trained operators and
maintenance personnel, as well as proper programs of operation and maintenance, are essential to the safe and
reliable operation of this appliance.
A. The responsibility of the manufacturer is to supply suitable, comprehensive instructions and recommendations
for the operation and maintenance of the appliance.
B. Trained qualied and factory-authorized personnel must perform all operation, maintenance and repair of these
appliances. It is the responsibility of the owner/operator to ensure that this happens.
C. A regular periodic program of cleaning, inspection and maintenance must be established and comprehensive
maintenance records maintained. It is the sole responsibility of the user to establish, schedule and enforce the
frequency and scope of these programs in keeping with recommended practice and with due consideration given
to actual operating conditions.
D. Operate this appliance within the limits it was designed for, which will not exceed the working limits of any component
within the appliance as a whole.
HIGH VOLTAGES ARE PRESENT INSIDE THIS APPLIANCE WHEN THE UNIT IS PLUGGED/
WIRED INTO A LIVE RECEPTACLE. BEFORE REPLACING ANY PARTS, DISCONNECT THE
WARNING
CAUTION
UNIT FROM THE ELECTRIC POWER SUPPLY.
USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY LANG
MANUFACTURING, OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY INJURY
OT THE OPERATOR AND DAMAGE TO THE EQUIPMENT EIWLL VOID ALL WARRANTIES.
GENERAL INFORMATION
Lockout Procedure
Announce lockout to other personnel.
Turn power off at main panel.
Test lockout by turning power switch on and observing if elements come on.
Check heater circuit with voltmeter.
Perform necessary repairs or tests.
Clear the unit of personnel before starting the griddle.
Turn power on at main panel.
Announce unit is “on” to other personnel.
Controls
The broiler turns on with the power switch of the griddle.
The broiler operates with full power when it is in the closed position. In the open position, the broiler will operate with
partial power and be in the “idle” mode.
2M-W363: Electric Clamshell® CSE12A
Controls Contact Clam
This broiler turns on using the separete control box, see Operating instructions on page 10.
4
GENERAL INFORMATION continued
Technical
The broiler, not including the griddle, is standard 208 or 240V, single phase. Specify voltage when ordering.
Receiving the Unit
Upon receipt, check for freight damage, both visible and concealed. Note visible damage
on the freight bill at the time of delivery and have the carrier’s agent sign the freight bill
at that time. Concealed loss or damage means loss or damage, which does not become
apparent until the merchandise has been unpacked. Make a written request for inspection
upon unpacking and nding concealed damage within 15 days of delivery. Keep all packing
material for inspection. Do not return damaged merchandise to Lang Manufacturing.
File your claim with the carrier.
Location
Prior to un-crating, move the unit as near its intended location as practical. The crating will help protect the unit from
the physical damage normally associated with moving it through hallways and doorways.
Un-crating
The unit will arrive completely assembled inside a wood frame covered by cardboard box and strapped
to a skid. Remove the cardboard cover, cut the straps and remove the wood frame.
CAUTION
NOTICE
SHIPPING STRAPS ARE UNDER TENSION AND CAN SNAP BACK WHEN CUT.
Remove unit from the skid.
2M-W363: Electric Clamshell® CSE12A
THE UNIT IS EXTREMELY HEAVY. FOR SAFE HANDLING, INSTALLER SHOULD OBTAIN
HELP AS NEEDED OR EMPLOY APPROPRIATE MATERIALS-HANDLING EQUIPMENT
(SUCH AS A FORKLIFT, DOLLY OR PALLET JACK) TO REMOVE THE UNIT FROM THE SKID
AND MOVE IT TO THE PLACE OF INSTALLATION.
ANY STAND, COUNTER OR OTHER DEVICE ON WHICH THE UNIT WILL BE LOCATED MUST
BE DESIGNED TO SUPPORT THE WEIGHT OF THE UNIT.
5
INSTALLATION
Electrical Connection
Verify griddle installation was performed as directed in
the installation instructions.
Connect electrical service to the box at the back of the
griddle.
Electrical specications are located on the data plate.
Clearance
Use this griddle only in non-combustible locations.
Maintain clearances of base appliance.
THIS APPLIANCE MUST BE GROUNDED AT THE TERMINAL PROVIDED. FAILURE TO
WARNING
WARNING
GROUND THE APPLIANCE COULD RESULT IN ELECTROCUTION AND DEATH.
INSTALLATION OF THE UNIT MUST BE DONE BY PERSONNEL QUALIFIED TO WORK
WITH ELECTRICITY AND PLUMBING. IMPROPER INSTALLATION CAN CAUSE INJURY
TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. UNIT MUST BE INSTALLED IN
ACCORDANCE WIHT ALL APPLICABLE CODES.
WARNING
NOTICE
NOTICE
BROILER ELEMENTS CAN IGNITE GREASE FIRES ON THE GRIDDLE SURFACE, WHICH
MAY RESULT IN PROPERTY DAMAGE, SERIOUS INJURY OR DEATH. ENSURE GRIDDLE
SURFACE IS SLOPPED DOWN FROM BACK TO FRONT BY AT LEAST 1/4” BEFORE
COOKING.
The data plate is located behind the Clamshell® between the two pivot arms. The
Clamshell® voltages, wattage, serial number, wire size and clearance specications are on
the data plate. Carefully read and understand this information before proceeding with the
installation.
The installation of any components such as a vent hood, grease extractors or re
extinguisher systems must be conform to the applicable National, State and locally
recognized installation standards.
2M-W363: Electric Clamshell® CSE12A
6
Loading...